P2300MEL

SIDACtor ® Protection Thyristors High Surge Current Protection Pxxx0ME 5kA SIDACtor Series® in TO-218 RoHS Pb e3 Description The 5kA series SIDACtor® components are designed to protect equipment located in high exposure environments from severe overvoltage transients. Setup in a robust TO-218 package, the 5kA series are ideal for use in data interface and AC power line for CATV amplifiers, Telecom Base Station equipment and Cell Towers. Features and Benefits Agency Approvals Agency • Pb-free E3 means 2nd level • Low voltage overshoot Agency File Number interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD-609A.01) • Low on-state voltage E133083 • Does not degrade surge capability after multiple surge events within limit. Pinout Designation • RoHS compliant, lead-free • Fails short circuit when 2 and halogen-free surged in excess of rating • UL Recognized as an • Rugged TO-218 package Isolated Loop Circuit Protector to UL 497B • 5000A 8/20 µs surge rating 1 2 3 (No Connection) Applicable Global Standards Schematic Symbol 1 2 • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd Edition • ITU K.20/21/45 Enhanced Level • YD/T 1082 • ITU K.20/21/45 Basic Level • YD/T 950 • YD/T 993 • GR 1089 Inter-building Electrical Characteristics Part Number Marking VDRM @lDRM=5µA VS @100V/µs IH IS IT VT @IT=2.2 A Capacitance @1MHz, 2V bias V min V max mA min mA max A max V max pF min pF max P1500MEL P1500ME 140 180 50 800 2.2/25 4 400 650 P1900MEL P1900ME 155 220 50 800 2.2/25 4 400 650 P2300MEL P2300ME 180 260 50 800 2.2/25 4 350 600 P2600MEL P2600ME 220 300 50 800 2.2/25 4 300 600 P3100MEL P3100ME 275 350 50 800 2.2/25 4 300 550 P3500MEL P3500ME 320 400 50 800 2.2/25 4 300 500 P3800MEL P3800ME 350 430 50 800 2.2/25 4 300 500 P4800MEL P4800ME 450 600 20 800 2.2/25 4 300 500 Notes: 1. Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). 2. Components are bi-directional (unless otherwise noted). 3. IT is a free air rating and heat sink is at 25A © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19 SIDACtor ® Protection Thyristors High Surge Current Protection Surge Ratings IPP 1.2/50 8/202 Series E ITSM 50 / 60 Hz di/dt 10/350 1.2/502 10/1000 10/1000 2 A min A min A min A min A/µs max 50003 1500 1100 400 630 1 1 1 Notes: 1. Voltage waveform in µs 2. Current waveform in µs 3. For surge rating of P3800MEL, it is minimum 4kA and typical 5kA @8/20µs. - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Conditions Package Symbol 2 3 (No Connection) Value Unit °C TJØ Operating Junction Temperature Range -40 to +150 TS Storage Temperature Range -65 to +150 °C TC Maximum Case Temperature 100 °C R0JC* Thermal Resistance: Junction to Case 1.7 °C/W R0JA Thermal Resistance: Junction to Ambient 56 °C/W TO-218 2 1 Parameter *R0JC rating assumes the use of a heat sink and on state mode for extended time at 25 A, with average power dissipation of 29.125 W. V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I 100 Normalized VS Change vs. Junction Temperature 50 Half Value 0 td tr t – Time (µs) Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Waveform = tr x td 0 -I tr = rise time to peak value td = decay time to half value Peak Value 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19 SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly Pre Heat - Temperature Min (Ts(min)) +150°C - Temperature Max (Ts(max)) +200°C - Time (Min to Max) (ts) 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. +260(+0/-5)°C Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification V-0 Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Wave Solder (THD) Parameters and Lead-Free Requirements Reflow Parameter Lead-Free Requirement Prehead (Depending on Flux Only) Temperature Min Temperature Max Time (Min to Max) 150ºC 200ºC 60 - 180 Seconds Solder Pot Temperature 245 - 265ºC (Max) Solder Dwell Time 2 - 3.5 Seconds Cooling -6ºC/Seconds (Max) Part Numbering P xxx 0 M E L TYPE P: SIDACtor RoHS COMPLIANT Compliant with Rohs Directive 2011/65/EU MEDIAN VOLTAGE IPP RATING CONSTRUCTION VARIABLE PACKAGE TYPE Part Marking XXXXXXX xxxxx Part Number Code (Refer to Electrical Characteristics Table) Date Code © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19 SIDACtor ® Protection Thyristors High Surge Current Protection Dimensions — TO-218 TC Measurement Point U DIA. B A Dimensions C Tab is connected to PIN 2 F E D PIN 3 J P PIN 1 H M Q PIN 2 R G N 3 Times K L Notes: • • • • Millimeters Max Min Max 0.810 0.835 20.57 21.21 B 0.610 0.630 15.49 16.00 C 0.178 0.188 4.52 4.78 D 0.055 0.070 1.40 1.78 E 0.487 0.497 12.37 12.62 16.64 A W Inches Min F 0.635 0.655 16.13 G 0.022 0.029 0.56 0.74 H 0.075 0.095 1.91 2.41 15.88 J 0.575 0.625 14.61 K 0.211 0.219 5.36 5.56 L 0.422 0.437 10.72 11.10 M 0.058 0.068 1,47 1.73 N 0.045 0.055 1.14 1.40 P 0.095 0.115 2.41 2.92 0.41 R 0.008 0.016 0.20 U 0.161 0.165 4.1 4.2 W 0.085 0.095 2.17 2.42 Mold flash shall not exceed 0.13 mm per side. Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Pin 3 has no connection. Tab is non-isolated (connects to middle pin). Packing Options Package Type M Description Packing Options Quantity Added Suffix Industry Standard TO-218 (ME) Tube Pack 250(25 per tube/10 tubes per box) N/A N/A TO-218 Tube Pack Specification Tube Pack Specification — TO-218 NOTES: (UNLESS OTHERWISE SPECIFIED) 1. 2. 3. 4. 5. 6. 7. INSIDE RADIUS: 1.3 MAX. TOLERANCES: +/- 0.25 MATERIAL: TRANSPARENT AND RIGID PVC TINT: CLEAR ANTISTATIC: YES TUBE CAPACITY:P 25 DEVICES TUBE WARPAGE NOT TO EXCEED: 0.08 PER 25.4 OR 1.5 END TO END 8. MAX. BURR ALLOWED ON INSIDE SURFACES 0.13 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/04/19