P2600S1BLRP

SIDACtor® Protection Thyristors Datasheet Pxxx0S1xL Series SIDACtor ® -DO-214AC Pb e3 RoHS Description SIDACtor ® SMA Thyristors Series are designed to protect baseband equipment such as phones, faxes, modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards. Features & Benefits ■ Low voltage overshoot ■ Low on-state voltage ■ Does not degrade surge capability after multiple surge events within limit. ■ RoHS Compliant and Halogen-Free Additional Information Resources ■ Low capacitance ■ Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applicable Global Standards Accessories Samples ■ TIA-968-A* ■ GR 1089 Intra-building ■ TIA-968-B* ■ IEC 61000-4-5 2nd edition ■ ITU K.20/21/45 Enhanced Level* ■ YD/T 1082 ■ ITU K.20/21/45 Basic Level ■ YD/T 950 ■ GR 1089 Inter-building* ■ YD/T 993 * Line impedance required to pass operationally Agency Approvals Agency ■ Fails short circuit when surged in excess of ratings Schematic Symbol Agency File Number E133083 Electrical Characteristics Part Number P0080S1ALRP P0220S1ALRP P0300S1ALRP P0640S1ALRP P1800S1ALRP P2300S1ALRP P2600S1ALRP P3100S1ALRP P3500S1ALRP P0080S1BLRP P0220S1BLRP P0300S1BLRP P0640S1BLRP P1800S1BLRP P2300S1BLRP P2600S1BLRP P3100S1BLRP P3500S1BLRP Marking P-8A P22A P03A P06A P18A P23A P26A P31A P35A P-8B P22B P03B P06B P18B P23B P26B P31B P35B VDRM @lDRM=5µA VS @100V/µs IH IS IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias V min V max mA min mA max A max V max pF min pF max 6 15 25 58 170 190 220 275 320 6 15 25 58 170 190 220 275 320 25 32 40 77 220 260 300 350 400 25 32 40 77 220 260 300 350 400 50 50 50 150 150 150 150 150 150 50 50 50 120 120 120 120 120 120 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 25 10 10 10 10 10 10 10 10 20 10 10 10 10 10 10 10 10 35 30 30 30 30 30 30 30 30 35 30 30 30 30 30 30 30 30 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional (unless otherwise noted). 1 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/15/23 SIDACtor® Protection Thyristors Datasheet Pxxx0S1xL Series SIDACtor ® -DO-214AC Surge Ratings Series IPP 0.2/310 0.5/700 2 2/10 2/10 2 8/20 1.2/50 2 10/160 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 1 1 1 1 ITSM 50/60 Hz di/dt Amps/µs max A min A min A min A min A min A min A min A min A min A min A 20 150 150 90 50 75 75 50 75 20 500 B - 250 250 90 60 75 75 55 75 25 500 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W DO-214AC V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (µs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 0 -4 -6 -8 -40 -20 0 1.8 1.6 1.4 1.0 0.8 0.6 0.4 20 40 60 80 100 120 140 160 -40 Junction Temperature (TJ) – °C 25°C 1.2 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 2 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/15/23 SIDACtor® Protection Thyristors Datasheet Pxxx0S1xL Series SIDACtor ® -DO-214AC Soldering Parameters Pre Heat - Temperature Max (Ts(max)) +200°C - Time (Min to Max) (ts) 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP TL Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 Critical Zone TL to TP tL T S(max) Ramp-down Preheat T S(min) tS 25 time to peak temperature (t 25ºC to peak) Physical Specifications Lead Material tP Ramp-up Temperature - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) +150°C Reflow Condition Time Environmental Specifications High Temp Voltage Blocking Temp Cycling Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level 3 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 -65°C, 1008 hrs. 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 +260°C, 30 secs. MIL-STD-750 (Method 2031) 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/15/23 SIDACtor® Protection Thyristors Datasheet Pxxx0S1xL Series SIDACtor ® -DO-214AC Part Numbering Part Marking P xxx 0 S1 x L RP Pxxx xxxxx Reel Pack Type P = SIDACtor Rohs Compliant Median Voltage Construction Variable Part Marking Code (Refer to Electrical Characteristics Table) Date Code IPP Rating A = A rating B = B rating Package Type Dimensions DO-214AC (SMA) Dimensions C A B H D F E G J L K I Solder Pads Inches Millimeters Min Max Min Max A 0.049 0.065 1.250 1.650 B 0.157 0.177 3.990 4.500 C 0.100 0.110 2.540 2.790 D 0.078 0.090 1.980 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.194 0.208 4.930 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - Packing Options (all dimensions in mm) Package Type Description Packing Options Quantity Added Suffix Industry Standard S1 DO-214AC Tape & Reel Pack 12mm/13” tape 5000 RP EIA-481 Tape and Reel Specification — DO-214AC 0.157 (4.0) 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 13.0 (330) Dimensions are in inches (and millimeters). 0.80 (20.2) Arbor Hole Dia. Direction of Feed 0.49 (12.5) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. 4 © 2023 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 05/15/23