P3500ECL

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - TO-92 Pb e3 RoHS Description SIDACtor® Series TO-92 are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a robust through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits • Low voltage overshoot • Fails short circuit when surged in excess of ratings • Low on-state voltage • Does not degrade surge capability after multiple surge events within limit. Agency Approvals Agency Agency File Number • Low capacitance • 2nd level interconnect is Pb-free per IPC/ JEDEC J-STD-609A.01 E133083 Applicable Global Standards Pinout Designation Pin 1 Pin 3 Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21 Enhanced Level* • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 950 • YD/T 993 • GR 1089 Inter-building* * A/B-rated parts require series resistance Electrical Characteristics Part Number Marking P0080EALxxx P0300EALxxx P0640EALxxx P0720EALxxx P0900EALxxx P1100EALxxx P1300EALxxx P1500EALxxx P1800EALxxx P2300EALxxx P2600EALxxx P3100EALxxx P3500EALxxx P0080EA P0300EA P0640EA P0720EA P0900EA P1100EA P1300EA P1500EA P1800EA P2300EA P2600EA P3100EA P3500EA VDRM @lDRM=5µA VS @100V/µs V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 2.2 2.2 2.2 2.2 2.2 2.2 25 15 40 35 35 30 25 25 25 25 20 20 20 150 140 60 60 55 50 45 40 35 35 35 35 35 Table continues on next page. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) Part Number Marking P0080EBLxxx P0300EBLxxx P0640EBLxxx P0720EBLxxx P0900EBLxxx P1100EBLxxx P1300EBLxxx P1500EBLxxx P1800EBLxxx xxx P2600EBLxxx P3100EBLxxx P3500EBLxxx P0080ECLxxx P0300ECLxxx P0640ECLxxx P0720ECLxxx P0900ECLxxx P1100ECLxxx P1300ECLxxx P1500ECLxxx P1800ECLxxx P2300ECLxxx P2600ECLxxx P3100ECLxxx P3500ECLxxx P0080EB P0300EB P0640EB P0720EB P0900EB P1100EB P1300EB P1500EB P1800EB P2300EB P2600EB P3100EB P3500EB P0080EC P0300EC P0640EC P0720EC P0900EC P1100EC P1300EC P1500EC P1800EC P2300EC P2600EC P3100EC P3500EC VDRM @lDRM=5µA VS @100V/µs V Min V Max 6 25 58 65 75 90 120 140 170 190 220 275 320 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 25 40 77 88 98 130 160 180 220 260 300 350 400 IH mA Min mA Max 50 50 150 150 150 150 150 150 150 150 150 150 150 50 50 150 150 150 150 150 150 150 150 150 150 150 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A Max V Max pF Min pF Max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 IS 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 25 15 40 35 35 30 25 25 25 25 20 20 20 35 25 55 50 45 45 40 35 35 30 30 30 25 150 140 60 75 70 70 60 55 50 50 45 45 40 260 250 155 150 140 115 105 95 90 80 80 70 65 Notes: - xxx part number suffix: ‘AP’ = Ammo Pack, ‘RP1’ and ‘RP2’ = Reel Pack, blank = Bulk Pack Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). Series Surge Ratings IPP 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 ITSM 50/60 Hz di/dt A min A min A min A min A min A min A min A min A min A min A/µs max A 20 150 150 90 50 75 75 45 75 20 500 B 25 250 250 150 100 100 125 80 100 25 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package TO-92 Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 IH 10 8 6 25 °C 4 1.8 IH (TC = 25ºC) 12 1.6 1.4 2 0 -4 1.0 0.8 0.6 -6 0.4 -8 -40 -20 0 25°C 1.2 Ratio of Percent of VS Change – % 14 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down TS(min) Preheat tS 25 time to peak temperature (t 25ºC to peak) Time SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Physical Specifications Environmental Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 Body Material High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Part Marking Part Numbering P xxx 0 E x L xxx TYPE P = SIDACtor PACKING OPTIONS MEDIAN VOLTAGE RoHS COMPLIANT CONSTRUCTION VARIABLE IPP RATING XXXXXXX XX Part Marking Code (Refer to Electrical Characteristics Table) XXXXX Date Code PACKAGE TYPE Packing Options Package Type Description Packing Options Quantity TO-92 Tape and Reel Pack E TO-92 Ammo Pack 2000 TO-92 Bulk Pack Added Suffix Lead Spacing RP1 0.1 inch (2.54mm) RP2 0.2 inch (5.08mm) Industry Standard EIA-481-D AP EIA-468-B N/A N/A Additional Information Datasheet Resources Samples © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions — TO-92 Ammo Pack Specification — TO-92 Temperature Measurement Point Inches A N B MT1/PIN 1 MT2/PIN 3 E G H L Min Max Min Max A 0.176 0.196 4.47 4.98 B 0.500 D 0.095 E 0.150 D 12.70 0.105 2.41 2.67 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0) 0.135 0.145 3.43 3.68 0.088 0.096 2.23 2.44 J The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. 1.27 (32.2) J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 0.157 DIA (4.0) 0.20 (5.08) Flat down ed n of Fe Directio 25 Devices per fold 1.7 (43) 1.52 Dimensions are in inches (and millimeters). K 0.125 (3.2) MAX 0.50 (12.7) H 0.60 0.25 (6.35) 0.50 (12.7) 3.81 G N M Millimeters All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) Mold flash shall not exceed 0.13 mm per side. 6.9 (175) 1.7 (43) 12.9 (327) Tape and Reel Specification — TO-92 FLAT SIDE OF TO-92 A Dimensions D W1 C B P H1 H W W3 ROUND SIDE OF TO-92 (RP1) W4 W2 F P0 Dimension Inches Minimum A (RP2) F Inches Millimeters Min Max Min Max A N/A B 4.016 14.173 N/A 360.0 N/A 102.0 N/A C D 3.386 N/A 86.0 N/A 0.795 N/A 20.2 N/A W1 1.181 1.968 30.0 50.0 P 0.496 0.504 12.60 12.80 P0 0.498 0.502 12.65 12.75 F(for RP1) 0.090 0.110 2.29 2.80 F(for RP2) 0.182 0.244 4.63 6.19 H N/A 1.673 N/A 42.50 H1 N/A 1.270 N/A 32.26 W 0.674 0.763 17.12 19.38 W2 0.354 0.370 8.25 9.75 W3 0.236 N/A 6.00 N/A W4 0.020 N/A 0.50 N/A Millimeters Maximum Minimum Maximum B Disclaimer Notice - Information believed to be accurate and reliable. However, users should independently evaluate the suitability of and N/A 14.173 N/Afurnished is360.0 test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. 4.016 102.0 at www.littelfuse.com/disclaimer-electronics. N/A Read completeN/A Disclaimer Notice C 3.386 D 0.795 N/A to change without 20.2notice. Specifications are subject N/A © 2017 Littelfuse, Inc. 86.0 N/A N/A W1 Revised: 02/23/17 1.181 1.968 30.0 50.0 P 0.496 0.504 12.60 12.80