P3500S1ALRP

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - SMA Description SIDACtor® SMA Series are designed to protect baseband equipment such as phones, faxes, modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards. Features and Benefits • Low voltage overshoot Agency Approvals Agency • Fails short circuit when surged in excess of ratings • Low on-state voltage • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133080 • Low capacitance Applicable Global Standards Schematic Symbol • TIA-968-A* • GR 1089 Intra-building • TIA-968-B* • IEC 61000-4-5* • ITU K.20/21 Enhanced Level* • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 950 • YD/T 993 • GR 1089 Inter-building* * Line impedance required to pass operationally Electrical Characteristics Part Number Marking P0080S1ALRP P1800S1ALRP* P2300S1ALRP* P2600S1ALRP* P3100S1ALRP P3500S1ALRP* P-8A P18A P23A P26A P31A P35A VDRM @lDRM=5µA VS @100V/µs V min V max 6 170 190 220 275 320 25 220 260 300 350 400 IH mA min mA max 50 150 150 150 150 150 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - Parts with “*” are under development © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. IS 1 Revised: March 2, 2012 800 800 800 800 800 800 IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 25 15 15 15 15 15 35 50 50 50 50 50 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Series Surge Ratings A IPP ITSM 50/60 Hz di/dt A min A min Amps/µs max 75 20 500 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 20 150 150 90 50 75 75 50 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W DO-214AC V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (µs) -I Normalized DC Holding Current vs. Case Temperature Normalized VS Change vs. Junction Temperature 8 6 25 °C 4 2 IH (TC = 25ºC) IH 10 Ratio of Percent of VS Change – % 2.0 14 12 0 -4 -6 0 1.4 Junction Temperature (TJ) – °C 25°C 1.2 1.0 0.8 0.6 -40 20 40 60 80 100 120 140 160 © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 1.6 0.4 -8 -40 -20 1.8 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 2 Revised: March 2, 2012 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material TL TS(max) tL Ramp-down Preheat TS(min) tS time to peak temperature (t 25ºC to peak) Time Environmental Specifications UL recognized epoxy meeting flammability classification 94V-0 © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Critical Zone TL to TP 25 Physical Specifications Lead Material tP Ramp-up Temperature Reflow Condition High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 3 Revised: March 2, 2012 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Part Marking Part Numbering P xxx 0 S1 A L RP Pxxx xxxxx REEL PACK TYPE P = SIDACtor RoHS COMPLIANT MEDIAN VOLTAGE CONSTRUCTION VARIABLE Part Marking Code (Refer to Electrical Characteristics Table) Date Code IPP RATING PACKAGE TYPE Dimensions DO-214AC (SMA) Dimensions C A B H D F E G J K L I Inches Min Max Min Max A 0.049 0.065 1.250 1.650 B 0.157 0.177 3.990 4.500 C 0.100 0.110 2.540 2.790 D 0.078 0.090 1.980 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.194 0.208 4.930 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - Solder Pads Packing Options Package Type S1 (all dimensions in mm) Description Packing Options Quantity Added Suffix Industry Standard DO-214AC Tape & Reel Pack 12mm/13” tape 5000 RP EIA-481 Tape and Reel Specification — DO-214AC 0.157 (4.0) 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) © 2012 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Dimensions are in inches (and millimeters). Direction of Feed 4 Revised: March 2, 2012 Millimeters Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: P3500S1ALRP