P3504UCMCLTP

SIDACtor® Datasheet Pxxx4UCMC Series MicroCapacitance Multiport SIDACtor ® - MS-013 RoHS Pb e3 Description The Pxxx4UCMC Series MS-013 are low capacitance SIDACtor® thyristors designed to protect broadband equipment from damaging overvoltage transients. The series provides a robust peak surge current capability that enables equipment to comply with various global regulatory standards while limiting the impact to broadband signals. Features and Benefits ■ Replaces four discrete components ■ Low voltage overshoot ■ Low on-state voltage ■ surge capability does not degrade after multiple surge events within limit Additional Information ■ Fails short circuit when surged in excess of ratings ■ Two-pair protection Resources Accessories Samples Pinout Designation Applicable Global Standards 1 6 ■ TIA-968-A ■ GR 1089 Intra-building 2 ■ TIA-968-B ■ IEC 61000-4-5, 2nd Edition 5 ■ YD/T 1082 3 ■ ITU K.20/21/45 Enhanced Level 4 ■ ITU K.20/21/45 Basic Level ■ YD/T 950 (T1) 1 ■ GR 1089 Inter-building (G1) 2 5 (G2) (R1) 3 4 (R2) Marking Electrical Characteristics VDRM @lDRM=5µA VS @100V/µs VDRM @lDRM=5µA VS @100V/µs V V V V 6 25 58 65 75 90 120 Agency File Number E133083 Pins 1-2, 3-2, 4-5, 6-5 P0084UCMC P0304UCMC P0644UCMC P0724UCMC P0904UCMC P1104UCMC P1304UCMC ■ YD/T 993 Agency Approvals 6 (T2) Agency P0084UCMCLxx P0304UCMCLxx P0644UCMCLxx P0724UCMCLxx P0904UCMCLxx P1104UCMCLxx P1304UCMCLxx ■ RoHS-compliant ■ 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Schematic Symbol Part Number ■ Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) 25 40 77 88 98 130 160 Pins 1-3, 4-6 12 50 116 130 150 180 240 50 80 154 176 196 260 320 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. - XX Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). IH IS IT VT @IT= 2.2 Amps mA min mA max A max V max 50 50 150 150 150 150 150 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 8 Capacitance See Capacitance Values Table Table continues on next page. 1 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.03/17/21 SIDACtor® Datasheet Pxxx4UCMC Series MicroCapacitance Multiport SIDACtor ® - MS-013 Electrical Characteristics (continued) Part Number VDRM @lDRM=5µA VS @100V/µs VDRM @lDRM=5µA VS @100V/µs V V V V Marking Pins 1-2, 3-2, 4-5, 6-5 P1504UCMCLxx P1804UCMCLxx P2304UCMCLxx P2604UCMCLxx P3104UCMCLxx P3504UCMCLxx 140 170 190 220 275 320 P1504UCMC P1804UCMC P2304UCMC P2604UCMC P3104UCMC P3504UCMC Pins 1-3, 4-6 180 220 260 300 350 400 280 340 380 440 550 600 IH IS VT @IT= 2.2 Amps IT Capacitance mA min mA max A max V max 150 150 150 150 150 150 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 360 440 520 600 700 800 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. - XX Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Capacitance Values Part Number pF Pin 1-2 / 3-2 (4-5 / 6-5) Tip-Ground, Ring-Ground P0084UCMCLxx P0304UCMCLxx P0644UCMCLxx P0724UCMCLxx P0904UCMCLxx P1104UCMCLxx P1304UCMCLxx P1504UCMCLxx P1804UCMCLxx P2304UCMCLxx P2604UCMCLxx P3104UCMCLxx P3504UCMCLXx pF Pin 1-3 (4-6) Tip-Ring MIN MAX MIN MAX 35 25 55 50 45 45 40 35 35 30 30 30 25 75 45 85 75 70 70 60 55 50 50 45 45 40 20 10 30 25 25 25 20 20 15 15 15 15 15 45 25 50 45 40 40 35 35 30 30 30 25 25 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP C ITSM 50/60 Hz di/dt A min A min A/µs max 200 30 500 0.2/310 1 0.5/700 2 2/10 1 2/10 2 8/20 1 1.2/50 2 10/160 1 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 Notes: 1. Current waveform in µs 2. Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C 2 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.03/17/21 SIDACtor® Datasheet Pxxx4UCMC Series MicroCapacitance Multiport SIDACtor ® - MS-013 Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 60 °C/W Modified MS-013 6 5 4 1 2 3 V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (µs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature IH 8 6 25 °C 4 IH (TC = 25ºC) 10 Ratio of Percent of VS Change – % 2.0 14 12 2 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 25°C 1.2 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C 3 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.03/17/21 SIDACtor® Datasheet Pxxx4UCMC Series MicroCapacitance Multiport SIDACtor ® - MS-013 Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP TL T S(max) Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material tL Preheat T S(min) tS 25 time to peak temperature (t 25ºC to peak) High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity High Temp Storage Part Numbering Low Temp Storage P xxx 4 UC MC L RP Thermal Shock REEL PACK Unbiased Highly Accelerated Stress Test RoHS COMPLIANT MEDIAN VOLTAGE Resistance to Solder Heat MC Series CONSTRUCTION VARIABLE IPP RATING PACKAGE TYPE Time Environmental Specifications UL Recognized epoxy meeting flammability classification V-0 TYPE P = SIDACtor Critical Zone TL to TP Ramp-down Physical Specifications Lead Material tP Ramp-up Temperature Reflow Condition Moisture Sensitivity Level MS-013 Part Marking Drawing_2009-03-05.eps 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/JEDEC, JESD22-A-101 +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 -65°C, 1008 hrs. 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 +130°C, 85%RH, 2atm, 96 hrs. JESD22-A-118 +260°C, 30 secs. MIL-STD-750 (Method 2031) 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-TD-020, Level 1 Part Marking XXXXXXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code XXXXX 4 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.03/17/21 SIDACtor® Datasheet Pxxx4UCMC Series MicroCapacitance Multiport SIDACtor ® - MS-013 Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) D J 7º TYP A Dimension are in inches (and millimeters). 0.059 (1.50) E 7º TYP A B C D E F G H J K BSC* G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F 7º TYP MIN Length of Flat K Detail A B Inches Millimeters Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 3.63 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) .512 (13.0) Arbor Hole Dia. 12.99 (330) Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Dimensions — MS-013 Message Location .045 (1.14) .310 (7.87) 90° .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A 20.000 ± .030 (508.00 ± 0.76) .110 (2.79) A Dimensions are in inches (and millimeters) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. 5 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.03/17/21