P4802ACMCL

SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Balanced MC Series - Modified TO-220 Pb e3 RoHS Description Balanced MC Series Modified TO-220 are low capacitance SIDACtor® components designed to protect broadband equipment from damaging overvoltage transients. The patented “Y” configuration also ensures balanced overvoltage protection that prevents a longitudinal to differential conversion. The series provides a single port solution that enables equipment to comply with various global requlatory standards while limiting the impact to broadband signals. Features and Benefits than our Baseband Protectors, for applications that demand greater signal integrity • Low voltage overshoot Agency Approvals • Low on-state voltage Agency • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 • Robust Modified TO-220 Package • Fails short circuit when surged in excess of ratings Pinout Designation • Custom lead forms available • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • Balanced overvoltage protection • RoHS Compliant, LeadFree, and Halogen-Free PIN 1 PIN 2 • 40% lower capacitance PIN 3 Applicable Global Standards Schematic Symbol 1 3 (R) (T) 2 (G) • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21/45 Enhanced Level • YD/T 1082 • ITU K.20/21/45 Basic • YD/T 950 • YD/T 993 • GR 1089 Inter-building Electrical Characteristics Part Number Marking VDRM @lDRM=5µA V min VS @100V/µs V max Pins 1-2, 3-2, 1-3 P1553ACMCLxx P1803ACMCLxx P2103ACMCLxx P2353ACMCLxx P2703ACMCLxx P3203ACMCLxx P3403ACMCLxx P5103ACMCLxx P1553ACMC P1803ACMC P2103ACMC P2353ACMC P2703ACMC P3203ACMC P3403ACMC P5103ACMC 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 IH IS IT VT @IT=2.2 Amps mA max Pins 1-2, 3-2, 1-3 mA max A max V min 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 8 8 8 8 8 8 8 8 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack. Special order item -- contact factory.) © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 Capacitance See Capacitance Values Table SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Capacitance Values Part Number P1553ACMCLxx P1803ACMCLxx P2103ACMCLxx P2353ACMCLxx P2703ACMCLxx P3203ACMCLxx P3403ACMCLxx P5103ACMCLxx pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 30 55 30 60 30 45 25 45 25 40 25 40 20 35 20 30 pF Pin 1-3 Tip-Ring MIN MAX 20 35 15 30 15 30 15 30 15 30 15 30 15 25 10 20 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP C ITSM 50/60 Hz di/dt A min A min A/µs max 200 30 500 0.2/310 0.5/700 2 2x/0 2/10 2 8/20 1.2/50 2 10/160 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 1 1 1 1 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Modified TO-220 PIN 1 PIN 2 Value Unit TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C 50 °C/W R0JA PIN 3 Parameter Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IT IS IH -V IDRM +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 10 IH 8 6 25 °C 4 2 1.8 IH (TC = 25ºC) 12 1.6 1.4 0 -4 -6 1.0 0.8 0.6 -8 -40 -20 0 25°C 1.2 Ratio of Percent of VS Change – % 14 0.4 -40 20 40 60 80 100 120 140 160 -20 Junction Temperature (TJ) – °C 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP TL TS(max) Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 Critical Zone TL to TP tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Physical Specifications Lead Material tP Ramp-up Temperature Reflow Condition High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 SIDACtor ® Protection Thyristors Broadband OptimizedTM Protection Part Numbering Part Marking P xxx 3 A C MC L xx TYPE P = SIDACtor PACKING OPTIONS MC Series IPP RATING PACKAGE TYPE Dimensions - Modified TO-220 A Tape and Reel Specification — Modified TO-220 Inches O D G Date Code RoHS COMPLIANT CONSTRUCTION VARIABLE Temperature Measurement Point F (Refer to Electrical Characteristics Table) xxxxx Blank, RP or 60 -for Type 60 orders, contact factory MEDIAN VOLTAGE Part Marking Code XXXXXXXXX P PIN 3 PIN 2 PIN 1 L M K H N J The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. Millimeters Min Max Min A 0.400 0.410 10.16 10.42 D 0.360 0.375 9.14 9.53 F 0.110 0.130 2.80 3.30 G 0.540 0.575 13.71 14.61 H 0.025 0.035 0.63 0.89 0.240 (6.10) Max J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.90 M 0.070 0.085 1.78 2.16 N O P 0.018 0.024 0.46 0.61 0.178 0.290 0.188 0.310 4.52 7.37 4.78 7.87 0.019 (0.5) 1.626 (41.15) 0.720 (18.29) 0.750 ± 0.010 (19.05 ± 0.25) 0.360 (9.14) 0.100 (2.54) 0.500 (12.7) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed 1.968 (50.0) Packing Options Package Type Description Quantity Added Suffix Industry Standard Modified TO-220 Tape and Reel Pack 700 RP EIA-468-B Modified TO-220 Bulk Pack 500 N/A N/A Modified TO-220, Type 60 Lead Form Bulk Pack 500 60 (special order item, contact factory for details) N/A A Additional Information Datasheet Resources Samples Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17