P4SMA400A-E

TVS Diodes Surface Mount – 400W > P4SMA-E P4SMA series Series P4SMA-E Series RoHS Pb e3 08/21/2020 41356 P4SMA Series Description Uni-directional The P4SMA-E series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 400 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 3.3 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 60 A VF 3.5 V TJ -65 to 150 °C Storage Temperature Range TSTG -65 to 175 °C Typical Thermal Resistance Junction to Lead RθJL 30 °C/W Typical Thermal Resistance Junction to Ambient RθJA 120 °C/W Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only Operating Temperature Range Notes: 1. Non-repetitive current pulse, per Fig.4 and derated above TJ (initial) =25ºC per Fig. 3. 2. Mounted on 5.0x5.0mm copper pad to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only. Functional Diagram Anode Uni-directional • High temperature to reflow soldering guaranteed: 260°C/40sec • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • EPI silicon technology • Meet MSL level1, per J-STD-020C, LF maximun peak of 260°C • Matte tin lead–free Plated • Halogen-free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applications Bi-directional Cathode • Excellent clamping capability • For surface mounted applications to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • 400W peak pulse power capability at 10/1000µs waveform, repetition rate (duty cycles):0.01% • Low incremental surge resistance • Fast response time: typically less than 1.0ps from 0V to BV min TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: August 31, 2020 11:42 AM TVS Diodes Surface Mount – 400W > P4SMA-E P4SMA series Series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) P4SMA350A-E P4SMA400A-E P4SMA440A-E P4SMA480A-E* P4SMA510A-E* P4SMA530A-E* P4SMA540A-E* P4SMA550A-E* P4SMA600A-E* P4SMA650A-E* P4SMA700A-E* P4SMA800A-E* P4SMA900A-E* P4SMA1000A-E* Reverse Stand off Marking Voltage VR (Volts) 350S 400S 440S 480S 510S 530S 540S 550S 600S 650S 700S 800S 900S 1000S 300 342 376 408 434 451 460 468 510 553 595 680 765 850 MIN MAX Test Current IT (mA) 332.0 380.0 418.0 456.0 485.0 503.5 513.0 522.5 570.0 617.5 665.0 760.0 855.0 950.0 368.0 420.0 462.0 504.0 535.0 556.5 567.0 577.5 630.0 682.5 735.0 840.0 945.0 1050.0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Breakdown Voltage VBR (Volts) @ IT Maximum Maximum Maximum Reverse Clamping Peak Pulse Leakage IR Voltage VC Current Ipp @ Ipp @ VR (A) (V) (µA) 482.0 548.0 602.0 658.0 698.0 725.0 740.0 760.0 822.0 891.0 959.0 1096.0 1233.0 1365.0 0.90 0.75 0.68 0.61 0.57 0.55 0.54 0.53 0.49 0.45 0.42 0.37 0.33 0.30 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Note: for parts with * are still under development I-V Curve Characteristics Uni-directional Vc VBR VR IR VF IT V Ipp PPPM VR VBR VC IR VF Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: August 31, 2020 11:42 AM TVS Diodes Surface Mount – 400W > P4SMA-E P4SMA series Series Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS TJ initial = Tamb 10 1 0.1 0.001 0.01 0.1 Time Figure 3 - Peak Pulse Power Derating Curve 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 10 Figure 4 - Pulse Waveform 100 80 60 40 20 0 1 td-Pulse Width (ms) 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) tr=10µsec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 175 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 10/1000µsec. Waveform as defined by R.E.A td 0 1.0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 1000.00 Transient Thermal Impedance ( °C/W) 1000 Cj (pF) 100.00 10.00 1.00 100 1000 VBR - Reverse Breakdown Voltage (V) 100 10 1 0.1 0.001 0.01 0.1 1 10 100 1000 TP - Pulse Duration (s) ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: August 31, 2020 11:42 AM TVS Diodes Surface Mount – 400W > P4SMA series P4SMA-E Series Figure 7 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100.0 60 I F- Peak Forward Current (A) IFSM - Peak Forward Surve Current (A) 70 50 40 30 20 10.0 1.0 10 0.1 0 1 10 0.0 100 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 VF - Peak Forward Voltage (V) Number of Cycles at 60 Hz Soldering Parameters Pre Heat Lead–free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3°C/second max TS(max) to TA - Ramp-up Rate 3°C/second max Reflow - Temperature (TA) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ts(min) Ramp-down ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Weight 0.002 ounce, 0.061 gram Temperature Cycling JESD22-A104 Case JEDEC DO-214AC. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity  olor band denotes positive end C (cathode) except bidirectional H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-A111 ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: August 31, 2020 11:42 AM TVS Diodes Surface Mount – 400W > P4SMA series P4SMA-E Series Dimensions DO-214AC (SMA) Dimensions Cathode Band (for Uni-directional products only) C A B H D F E G L K J I Solder Pads (all dimensions in mm) Part Numbering System Inches Millimeters Min Max Min Max A 0.049 0.065 1.250 1.650 B 0.157 0.181 3.990 4.600 C 0.095 0.110 2.400 2.790 D 0.075 0.090 1.900 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.189 0.208 4.800 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - Part Marking System P4SMA XXX A-E Cathode Band (for Uni-directional products only) F EPI SILICON TECHNOLOGY 5% VBR VOLTAGE TOLERANCE XX VBR VOLTAGE YMXXX SERIES Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Part number Component Package P4SMAxxxA-E DO-214AC Packaging Option Quantity 5000 Tape & Reel - 12mm tape/13” reel Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) Dimensions are in inches (and millimeters). Direction of Feed ©2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: August 31, 2020 11:42 AM