PLED380S

PLED in Ballast Output LED Driver for Ignition PLEDApplication Open LED Protectors PLED Ultra Low Holding Current Series PLED Ultra Low Holding Current Series RoHS Description This PLED ultra-low holding current series exhibits a low holding current parameter that makes it compatible with LED lighting strings. The series provide a switching electronic characteristics for an fluorescent tube replacement by an LED string. It helps to make the Fluorescent ballast and LED string compatible with each other. This ensures the ballast will be able to activate the LED string; especially for those ballast that need a high voltage output detection during ignition.The PLED ultralow IH makes the LED driver widely used in the output of fluorescent tubes a compatible direct replacement for indoor and outdoor LED lighting strings. Schematic Symbol Features & Benefits • Fast switching • Automatically resets after power cycle Control Circuit • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC 801-2) • Compatible with industrial lighting environments • Available in low profile, Standard DO-214AA packages • IEC-61000-4-2 ESD 30kV (Air), 30kV (Contact) • RoHS compliant and halogen-free Electrical Characteristics (All parameters are measured at TA=25°C unless otherwise noted) VBR Part Number Marking Breakdown Volts Min Max VDRM IH IS VT @ IT = 1 Amp IO 1 Critical rate of rise dV/dt Volts mAmps mAmps Volts Amps Volts Min Max Max Max Max Min PLED64S PL64 58 71 56 21 800 2 1.0 250V/µs PLED70S PL70 65 81 63 21 800 2 1.0 250V/µs PLED90S PL90 75 90 73 21 800 2 1.0 250V/µs PLED110S PL110 90 120 87 21 800 2 1.0 250V/µs PLED130S PL130 120 149 116 21 800 2 1.0 250V/µs PLED150S PL150 136 167 132 21 800 2 1.0 250V/µs PLED180S PL180 170 203 165 21 800 2 1.0 250V/µs PLED230S PL230 190 240 184 21 800 2 1.0 250V/µs PLED260S PL260 220 274 213 21 800 2 1.0 250V/µs PLED310S PL310 275 330 267 21 800 2 1.0 250V/µs PLED350S PL350 320 380 310 21 800 2 1.0 250V/µs PLED380S PL380 350 430 340 21 800 2 1.0 250V/µs PLED450S2 PL450 410 495 397 21 800 2 1.0 250V/µs PLED480S PL480 450 600 436 21 800 2 1.0 250V/µs 2 note: 1. IO- Operation current tested @ aluminum boards, ambient temp 85°C 2. PLED450S and PLED480S are still under developed, please contact local sales representative for further information ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 10/15/18 PLED in Ballast Output LED Driver for Ignition PLEDApplication Open LED Protectors PLED Ultra Low Holding Current Series Thermal Considerations Package Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +125 °C TS Storage Temperature Range -65 to +150 °C RθJA Thermal Resistance: Junction to Ambient 901 402 °C/W DO-214 Notes: 1) Standard FR-4 PCB with Copper Pads (Recommended Size) 2) Aluminum PCB Thickness: 1.6mm Grade: 1-2 W/mK Thermal Conductivity Trace thickness: 2 oz Insulation layer thickness: 215 um Solder Pad Dimensions: 2.0mm x 2.8mm (Recommended Size) V-I Characteristics VBR vs. Junction Temperature +I IS IH -V +V VT VDRM VBR P e rc e n t o f VBR C h a n g e – % 14 IT 12 10 8 6 2 0 -4 -6 -8 -40 -20 iH (T C = 2 5 ˚C ) R a tio o f iH Normalized DC Holding Current vs. Case Temperature 2.0 1.8 1.6 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (T C ) – ˚C ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 10/15/18 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ ) – ˚C -I 1.4 25 ˚C 4 PLED in Ballast Output LED Driver for Ignition PLEDApplication Open LED Protectors PLED Ultra Low Holding Current Series Soldering Parameters Pb – Free assembly Reflow Condition 150°C - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 30 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes max Do not exceed 260°C Physical Specifications Terminal Material Copper Alloy Terminal Finish 100% Matte Tin Plated UL Recognized compound meeting flammability rating V-0. Body Material Environmental Specifications High Temperature Voltage Blocking MIL-STD-750: Method 1040, Condition A 80% min VDRM (VAC-peak), 125°C,1008 hours Temperature Cycling MIL-STD-750: Method 1051,-55°C to 150°C, 15-minute dwell,1000 cycles Biased Temperature & Humidity EIA/JEDEC: JESD22-A101 52VDC, 85°C, 85%RH, 1008 hours Thermal Shock MIL-STD-750: Method 1056 0°C to 100°C, 5-minute dwell, 10-second transfer, 10 cycles Resistance to Solder Heat MIL-STD-750: Method 2031 260°C, 10 seconds Moisture Sensitivity 85%RH, +85°C, 168 hours, 3 reflow cycles Level (+260°C peak). JEDEC-J-STD-020, Level 1 Dimensions - DO-214 AA Package B CASE TEMPERATURE MEASURING POINT D A C K Dimensions H E F G 0.079" (2.0mm) 0.110" (2.8mm) 0.079" (2.0mm) Recommended solder pad layout (Reference Only) ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 10/15/18 Inches Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 PLED PLED Application Open LED in Ballast Protectors Output LED Driver for Ignition PLED Ultra Low Holding Current Series Part Numbering System Part Marking System PLED 310 S PLX PACKAGE TYPE TYPE S:DO-214AA PLED: LED Protector XXXXX V BR See Electrical Characteristic table Packaging Package Description Packaging Quantity Industry Standard S DO-214AA 2500 EIA-481-1 DO-214 Embossed Carrier Reel Pack (RP) Meets all EIA-481-1 Standards 0.157 (4.0) 0.47 (12.0) 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ©2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 10/15/18