Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Q6008xH1LED Series
RoHS
Description
Q6008xH1LED series is designed to meet low load current
characteristics typical in LED lighting applications.
By keeping holding current at 6mA maximum, this Triac
series is characterized and specified to perform best with
LED loads. The Q6008xH1LED series is best suited for LED
dimming controls to obtain the lowest levels of light output
with a minimum probability of flickering.
Features
Agency Approval
Agency
Agency File Number
t"TMPXBTN"NBY
holding current
t1SPWJEFTGVMMDPOUSPM
of light out put at the
extreme low end of load
conditions.
t-1BDLBHFJT6-
recognized for 2500Vrms
t7AC min isolation
between mounting tab
and active terminals
t °C rated junction
t*NQSPWFTNBSHJOPGTBGF
operation with less heat
sinking required
-1BDLBHF&
®
Main Features
Symbol
IT(RMS)
VDRM /VRRM
IGT
Value
Unit
8
A
600
V
10
mA
temperature
Schematic Symbol
MT2
MT1
Benefits
tEJEUQFSGPSNBODFPG
70A/μs
t&OBCMFTVSWJWBCJMJUZ
of typically LED load
operating characteristics
t26"%3"$WFSTJPO
includes intergrated DIAC
t4JNQMJDJUZPGDJSDVJUEFTJHO
& layout
Applications
Excellent for AC switching and phase control applications
such as heating, lighting, and motor speed controls.
G
5ZQJDBMBQQMJDBUJPOTBSF"$TPMJETUBUFTXJUDIFT
MJHIUJOH
controls with LED lamp loads, small low current motor in
power tools, and low current motors in home/brown goods
appliances.
Internally constructed isolated packages are offered for
ease of heat sinking with highest isolation voltage.
Q6008xH1LED Series
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09//14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Absolute Maximum Ratings
Symbol
Parameter
Test Conditions
Q6008LH1LED
IT(RMS)
3.4POTUBUFDVSSFOU GVMMTJOFXBWF
Q6008RH1LED
/POSFQFUJUJWFTVSHFQFBLPOTUBUFDVSSFOU
(full cycle, TJJOJUJBM ¡$
I t
Unit
8
A
TC = 80°C
TC ¡$
Q6008NH1LED
ITSM
Value
G )[
U NT
80
f = 60 Hz
t = 16.7 ms
tp NT
As
A
It Value for fusing
di/dt
$SJUJDBMSBUFPGSJTFPGPOTUBUFDVSSFOU
G )[
TJ = 110°C
70
A/μs
IGTM
1FBLHBUFUSJHHFSDVSSFOU
t1 d 10 μs;
IGT d IGTM
TJ = 110°C
1.6
A
1G(AV)
Average gate power dissipation
TJ = 110°C
IGT N"
W
Storage temperature range
UP
°C
0QFSBUJOHKVODUJPOUFNQFSBUVSFSBOHF
UP
°C
Tstg
TJ
Electrical Characteristics (TJ = 25°C, unless otherwise specified)
Symbol
IGT
Test Conditions
Quadrant
Value
Unit
10
mA
V
MIN.
V
I – II – III
VD 73L = 60 :
MAX.
VGT
I – II – III
VGD
VD = VDRM RL L: TJ = 110°C
I – II – III
IH
IT N"
MAX.
6
mA
dv/dt
VD = VDRM(BUF0QFO5J = 110°C
MIN.
V/μs
(dv/dt)c
EJEU
D "NT5J = 110°C
MIN.
10
V/μs
tgt
IG N"18 T*T " QL
5:1
μs
Value
Unit
MAX.
1.60
V
MAX.
μA
Static Characteristics
Symbol
Test Conditions
ITM "Up T
VTM
IDRM
VDRM = VRRM
IRRM
TJ = 110°C
Thermal Resistances
Symbol
Parameter
Value
Q6008LH1LED
RT +$
Junction to case (AC)
Q6008xH1LED Series
°C/W
Q6008RH1LED
Q6008NH1LED
Unit
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Figure 2: Normalized DC Gate Trigger Current for
All Quadrants vs. Junction Temperature
Figure 1: Definition of Quadrants
ALL POLARITIES ARE REFERENCED TO MT1
3.5
MT2 POSITIVE
(Positive Half Cycle)
3.0
(+)
I GT
GATE
MT1
MT1
REF
I GT
MT2
(-)
I GT
GATE
(+)
MT1
REF
REF
QII QI
QIII QIV
-
IGT (TJ = 25°C)
I GT
GATE
MT2
IGT
(-)
+
2.5
2.0
Ratio of
MT2
+ IGT
MT2
1.5
1.0
0.5
I GT
GATE
0.0
MT1
-
MT2 NEGATIVE
(Negative Half Cycle)
-65
-40
-15
REF
10
35
60
85
110
Junction Temperature (TJ)- ºC
/PUF"MUFSOJTUPSTXJMMOPUPQFSBUFJO2*7
Figure 3: Normalized DC Holding Current
vs. Junction Temperature
Figure 4: Normalized DC Gate Trigger Voltage for
All Quadrants vs. Junction Temperature
3.5
2.0
2.0
VGT (TJ = 25°C)
VGT
2.5
1.5
1.0
Ratio of
1.5
Ratio of
IH
IH (TJ = 25°C)
3.0
1.0
0.5
0.5
0.0
0.0
-65
-40
-15
10
35
60
85
-65
110
-40
-15
35
60
85
110
Figure 6: Maximum Allowable Case Temperature
vs. On-State Current (Standard / Alternistor Triac)
Figure 5: Power Dissipation (Typical)
vs. RMS On-State Current
18
130
16
120
14
Maximum Allowable
Case Temperature (TC) - °C
Average On-State
Power Dissipation (PD(AV)) - Watts
10
Junction Temperature (TJ)- ºC
Junction Temperature (TJ)- ºC
12
10
8
6
4
Q6880RH1LED
Q6008NH1LED
110
100
Q6008LH1LED
90
80
70
2
0
60
0
2
4
6
8
10
0
Q6008xH1LED Series
1
2
3
4
5
6
7
8
RMS On-State Current (IT(RMS)) - Amps
RMS On-State Current (IT(RMS)) - Amps
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Figure 7: On-State Current vs. On-State Voltage
(Typical)
20
Postitive or Negative Instantaneous
On-State Current (iT) - Amps
TC = 25°C
16
12
8
4
0
0.6
0.8
1.0
1.2
1.4
1.6
Postitive or Negative Instantaneous
On-State Voltage (vT) - Volts
Figure 8: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-Repetitive)
On-State Current (ITSM) - Amps
100
4611-:'3&26&/$:)[4JOVTPJEBM
-0"%3FTJTUJWF
3.40O4UBUF$VSSFOU.BYJNVN3BUFE
Value at Specified Case Temperature
/PUFT
1. Gate control may be lost during and immediately
following surge current interval.
0WFSMPBENBZOPUCFSFQFBUFEVOUJMKVODUJPO
UFNQFSBUVSFIBTSFUVSOFEUPTUFBEZTUBUF
rated value.
10
1
1
10
100
1000
Surge Current Duration- Full Cycles
Q6008xH1LED Series
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Soldering Parameters
Reflow Condition
1Co'SFFBTTFNCMZ
Pre Heat
¡$
- Temperature Max (Ts(max))
¡$
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus Temp)
(TL) to peak
¡$TFDPOENBY
TS(max) to TL - Ramp-up Rate
¡$TFDPOENBY
Reflow
- Temperature (TL) (Liquidus)
¡$
- Temperature (tL)
oTFDPOET
Peak Temperature (TP)
°C
Time within 5°C of actual peak
Temperature (tp)
oTFDPOET
Ramp-down Rate
¡$TFDPOENBY
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
¡$
Temperature
- Temperature Min (Ts(min))
Ramp-up
TL
tL
TS(max)
Preheat
TS(min)
tS
time to peak temperature
Terminal Material
Time
Environmental Specifications
Test
.BUUF5JOQMBUFE
AC Blocking (VDRM)
Body Material
Ramp-do
Ramp-down
25
Physical Specifications
Terminal Finish
tP
TP
6-SFDPHOJ[FEFQPYZNFFUJOHnBNNBCJMJUZ
DMBTTJmDBUJPO7
Temperature Cycling
Copper Alloy
Temperature/
Humidity
Specifications and Conditions
.*-45%
.
$POE""QQMJFE
1FBL"$WPMUBHF!¡$GPSIPVST
.*-45%
.
DZDMFT ¡$UP ¡$ NJO
EXFMMUJNF
&*"+&%&$
+&4%"
IPVST 7%$¡$
rel humidity
.*-45%
.
IPVST ¡$
Design Considerations
High Temp Storage
Careful selection of the correct device for the application’s
operating parameters and environment will go a long way
toward extending the operating life of the Thyristor. Good
design practice should limit the maximum continuous
DVSSFOUUISPVHIUIFNBJOUFSNJOBMTUPPGUIFEFWJDF
SBUJOH0UIFSXBZTUPFOTVSFMPOHMJGFGPSBQPXFSEJTDSFUF
semiconductor are proper heat sinking and selection of
WPMUBHFSBUJOHTGPSXPSTUDBTFDPOEJUJPOT0WFSIFBUJOH
overvoltage (including dv/dt), and surge currents are
the main killers of semiconductors. Correct mounting,
soldering, and forming of the leads also help protect
against component damage.
Low-Temp Storage
IPVST ¡$
Autoclave
&*"+&%&$
+&4%"
IPVST ¡$BU"5.T
BOE
3)
Resistance to
Solder Heat
.*-45%.FUIPE
Solderability
"/4*+45%
DBUFHPSZ
5FTU"
Lead Bend
.*-45%
.$POE&
Q6008xH1LED Series
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead
TC MEASURING POINT
O
A
Ø E
Dimension
8.13
.320
P
MT2
B
C
A
AREA (REF.)
0.17 in 2
13.36
.526
D
7.01
.276
F
NOTCH IN GATE LEAD
TO ID. NON-ISOLATED TAB
R
G
Inches
Millimeters
Min
Max
Min
Max
10.67
B
C
D
E
'
0.110
G
H
J
K
L
0.060
M
N
0.018
0.61
L
H
K
N
J
/PUF.BYJNVNUPSRVFUP
be applied to mounting tab
JTJOMCT /N
M
MT1 MT2 GATE
0
0.178
0.188
1
0.060
R
Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab
AREA (REF.) 0.17 IN2
TC MEASURING POINT
O
A
E
P
Dimension
8.13
.320
A
B
C
13.36
.526
D
7.01
.276
F
R
G
K
N
J
MT1 MT2 GATE
Q6008xH1LED Series
M
/PUF.BYJNVNUPSRVFUP
be applied to mounting tab
JTJOMCT /N
Millimeters
Min
Max
Min
Max
10.67
B
C
D
E
'
0.110
G
H
J
K
L
0.060
M
N
0.018
0.61
L
H
Inches
0
0.178
0.188
1
0.060
R
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
Dimensions — TO-263AB (N-Package) — D2-PAK Surface Mount
TC MEASURING POINT
B
Inches
AREA: 0.11 IN2
C
V
Dimension
E
MT2
7.01
.276
A
8.41
.331
Millimeters
Min
Max
Min
Max
A
B
10.67
S
W
U
8.13
.320
G
H
D
F
11.68
.460
2.16
.085
7.01
.276
7.01
.276
16.89
.665
8.89
.350
0.178
0.188
E
0.060
'
0.060
G
H
J
K
GATE
MT1
C
D
1.40
.055
3.81
.150
2.03
.080
J
0.018
0.61
K
0.110
S
V
6
0.010
W
0.070
1.016
1.78
6.60
.260
Product Selector
Gate Sensitivity Quadrants
Part Number
Type
Package
I – II – III
Q6008LH1LED
10 mA
Alternistor Triac
50-
Q6008RH1LED
10 mA
Alternistor Triac
503
Q6008NH1LED
10 mA
Alternistor Triac
50%1",
Packing Options
Part Number
Marking
Weight
Packing Mode
Base Quantity
Q6008LH1LED
Q6008LH1
H
Bulk
2-)-&%51
Q6008LH1
H
5VCF1BDL
QFSUVCF
Q6008RH1LED
Q6008RH1
H
Bulk
23)-&%51
Q6008RH1
H
5VCF1BDL
QFSUVCF
Q6008NH1LED
Q6008NH1
1.6g
Tube
QFSUVCF
Q6008NH1LED
Q6008NH1
1.6g
Embossed Carrier
QFSUVCF
Q6008xH1LED Series
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
Teccor® brand Thyristors
8 Amp Alternistor (High Commutation) Triac for LED dimmer application
TO-263 Embossed Carrier Reel Pack (RP) Specifications
Meets all EIA-481-2 Standards
0.63
(16.0)
0.157
(4.0)
Gate
0.059
DIA
(1.5)
MT1
0.945
(24.0)
0.827
(21.0)
*
* Cover tape
MT2
0.512 (13.0) Arbor
Hole Dia.
12.99
(330.0)
Dimensions
are in inches
(and millimeters).
1.01
(25.7)
Direction of Feed
Part Numbering System
Part Marking System
TO-220 AB - (L and R Package)
TO-263 AB - (N Package)
Q 60 08 L H1 LED
DEVICE TYPE
Q : Alternistor Triac
LED LIGHTING APPLICATION
VOLTAGE RATING
60 : 600V
SENSITIVITY & TYPE
H1: 10mA (QI, II & III)
CURRENT
08: 8A
PACKAGE TYPE
L : TO-220 Isolated
R: TO-220 Non-Isolated
Q6008LH1
YMXXX
®
N: TO-263 (D2 Pak)
Date Code Marking
Y:Year Code
M: Month Code
XXX: Lot Trace Code
Q6008xH1LED Series
©2014 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/02/14
很抱歉，暂时无法提供与“Q6012RH1LED”相匹配的价格&库存，您可以联系我们找货
免费人工找货
工商网监
湘ICP备2023018690号
