RUE250U-2

RUE(7) 1/15/99 11:28 AM Page 141 RUE Selection Guide and Product Data This section has two parts: • A Selection Guide that walks you through the process of selecting the correct RUE device for a circuit. • Product Data that outlines electrical characteristics, physical characteristics, agency recognitions, environmental specifications, component layouts, tape and reel specifications, and ordering information for RUE devices. RUE Selection Guide Follow these seven steps to select a PolySwitch RUE device for a circuit: 1. Define the operating parameters for the circuit. These include: • Maximum ambient operating temperature • Normal operating current • Maximum operating voltage (RUE is 30 V maximum) • Maximum interrupt current 2. Select the RUE device that accommodates the circuit’s maximum ambient operating temperature and normal operating current. 3. Compare the RUE device’s maximum operating voltage and maximum interrupt current with the circuit’s to be sure the circuit does not exceed the device ratings. 4. Check the RUE device’s time-to-trip to be sure it will protect the circuit. 5. Verify that the circuit’s ambient operating temperatures are within the RUE device’s operating temperature range. 6. Verify that the RUE device’s dimensions fit the application’s space considerations. 7. Independently evaluate and test the suitability and performance of the RUE device in the application. ®  Raychem Circuit Protection Devices TUV Rheinland RUE Devices 141 4 RUE(7) 1/15/99 11:28 AM Page 142 RUE Radial Leaded 1. Define the circuit’s operating parameters. Fill in the following information about the circuit: Maximum ambient operating temperature _______________ Normal operating current _______________ Maximum operating voltage (RUE is 30 V max.) _______________ Maximum interrupt current _______________ 2. Select the PolySwitch RUE device that will accommodate the circuit’s maximum ambient operating temperature and normal operating current. Look across the top of the table below to find the temperature that most closely matches the circuit’s maximum ambient operating temperature. Look down that column to find the value equal to or greater than the circuit’s normal operating current. Now look to the far left of that row to find the part number for the RUE device that will best accommodate the circuit. 4 The thermal derating curve located on the next page is a normalized representation of the data in the table below. IHold vs. temperature Part number RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 142 RUE Devices Maximum –40° 1.31 1.60 1.96 2.32 2.68 3.63 4.35 5.80 7.25 8.70 10.15 11.60 13.05 ambient operating temperatures (°C) –20° 0° 20° 40° 1.17 1.04 0.90 0.75 1.43 1.27 1.10 0.91 1.76 1.55 1.35 1.12 2.08 1.84 1.60 1.33 2.41 2.13 1.85 1.54 3.25 2.88 2.50 2.08 3.90 3.45 3.00 2.49 5.20 4.60 4.00 3.32 6.50 5.75 5.00 4.15 7.80 6.90 6.00 4.98 9.10 8.05 7.00 5.81 10.40 9.20 8.00 6.64 11.70 10.35 9.00 7.47 50° 0.69 0.85 1.04 1.23 1.42 1.93 2.31 3.08 3.85 4.62 5.39 6.16 6.93 60° 0.61 0.75 0.92 1.09 1.26 1.70 2.04 2.72 3.40 4.08 4.76 5.44 6.12 70° 0.55 0.67 0.82 0.98 1.13 1.53 1.83 2.44 3.05 3.66 4.27 4.88 5.49 85° 0.47 0.57 0.70 0.83 0.96 1.30 1.56 2.08 2.60 3.12 3.64 4.16 4.68 Raychem Circuit Protection Devices RUE(7) 1/15/99 11:28 AM Page 143 RUE Radial Leaded Thermal derating curve Percent of rated hold and trip current 200 150 100 50 0 –40 –20 0 20 40 60 80 Device’s ambient temperature (°C) 3. Compare maximum operating voltages and maximum interrupt currents. Look down the first column of the table below to find the part number you selected in Step 1. Look to the right in that row to find the device’s maximum operating voltage (V max.) and maximum interrupt current (I max.). Compare both ratings with the circuit’s to be sure the circuit’s ratings do not exceed those of the RUE device. Maximum device voltages and currents Part number RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 V max. (volts) 30 30 30 30 30 30 30 30 30 30 30 30 30 I max. (amps)* 40 40 40 40 40 40 40 40 40 40 40 40 40 *Device may withstand higher interrupt current at lower voltages. Each application will need to be individually qualified. Raychem Circuit Protection Devices RUE Devices 143 4 RUE(7) 1/15/99 11:28 AM Page 144 RUE Radial Leaded 4. Determine time-to-trip. Time-to-trip is the amount of time it takes for a device to switch to a high-resistance state once a fault current has been applied across the device. Identifying the RUE device’s time-to-trip is important in order to provide the desired protection capabilities. If the device you choose trips too fast, undesired or nuisance tripping will occur. If the device trips too slowly, the components being protected may be damaged before the device switches to a high-resistance state. The chart below shows the typical time-to-trip at 20°C for each PolySwitch RUE device. For example, the chart indicates that the typical time-to-trip for RUE110 at 8 A is 1 second. On the chart below, find the typical time-to-trip for the RUE device you selected. If the RUE device’s time-to-trip is too fast or too slow for the circuit, go back to Step 2 and choose an alternate device. Typical time-to-trip at 20°C A= B= C= D= E= F= G= H= I = J = K= L= M= RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 AB C D E FG H I J K LM 1000 100 Time-to-trip (s) 4 10 1 0.1 0.01 0.001 1 10 100 Fault current (A) 144 RUE Devices Raychem Circuit Protection Devices RUE(7) 1/15/99 11:28 AM Page 145 RUE Radial Leaded 5. Verify ambient operating conditions. Ensure that your application’s minimum and maximum ambient temperatures are within the operating temperature range of –40°C and 85°C. Maximum device surface temperature in the tripped state is 125°C. 6. Verify the RUE device’s dimensions. Using dimensions from the table below, compare the dimensions of the RUE device you selected with the application’s space considerations. Product dimensions (millimeters/inches) Part number RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 A max. 7.4 (0.29) 7.4 (0.29) 8.9 (0.35) 8.9 (0.35) 10.2 (0.40) 11.4 (0.45) 11.4 (0.45) 14.0 (0.55) 14.0 (0.55) 16.5 (0.65) 19.1 (0.75) 21.6 (0.85) 24.1 (0.95) Lead size RUE090–RUE250 RUE300–RUE900 B max. 12.2 (0.48) 14.2 (0.56) 13.5 (0.53) 15.2 (0.60) 15.7 (0.62) 18.3 (0.72) 17.3 (0.68) 20.1 (0.79) 24.9 (0.98) 24.9 (0.98) 26.7 (1.05) 29.2 (1.15) 29.7 (1.17) C typ. 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 10.2 (0.40) 10.2 (0.40) 10.2 (0.40) 10.2 (0.40) 10.2 (0.40) D min. 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) RUE090–RUE250* Ø 0.51 (0.020) 24 AWG Ø 0.81 (0.032) 20 AWG A E max. 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) Raychem Circuit Protection Devices 4 RUE300–RUE900** E A E Marking Marking B B D D * Straight leads are available ** Kinked leads are available 0.8 0.8 0.8 0.8 0.8 0.8 1.2 1.2 1.2 1.2 1.2 1.2 1.2 F typ. (0.03) (0.03) (0.03) (0.03) (0.03) (0.03) (0.05) (0.05) (0.05) (0.05) (0.05) (0.05) (0.05) F C CL CL CL C CL CL CL F CL CL RUE Devices 145 RUE(7) 1/15/99 11:28 AM Page 146 RUE Radial Leaded RUE Product Data Now that you have selected your RUE device, please review the device’s characteristics in this section to verify that the device will perform as required. Electrical characteristics (20°C) 4 Part Number RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 IH (A) 0.90 1.10 1.35 1.60 1.85 2.50 3.00 4.00 5.00 6.00 7.00 8.00 9.00 IT (A) 1.80 2.20 2.70 3.20 3.70 5.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 Max. time to trip (s) at 5 x IH 5.9 6.6 7.3 8.0 8.7 10.3 10.8 12.7 14.5 16.0 17.5 18.8 20.0* Pd (W) 0.6 0.7 0.8 0.9 1.0 1.2 2.0 2.5 3.0 3.5 3.8 4.0 4.2 Initial resistance R min. (Ω) 0.070 0.050 0.040 0.030 0.030 0.020 0.020 0.010 0.010 0.005 0.005 0.005 0.005 R max. (Ω) 0.12 0.10 0.08 0.07 0.06 0.04 0.05 0.03 0.03 0.02 0.02 0.02 0.01 Post-trip resistance R1 max . (Ω) 0.22 0.17 0.13 0.11 0.09 0.07 0.08 0.05 0.05 0.04 0.03 0.02 0.02 IH = Hold current—maximum current at which the device will not trip at 20°C. IT = Trip current—minimum current at which the device will always trip at 20°C. Pd = Typical power dissipation—typical amount of power dissipated by the device when in tripped state in 20°C still air. R min. = Minimum device resistance at 20°C prior to tripping. R max. = Maximum device resistance at 20°C prior to tripping. R1 max. = Maximum device resistance at 20°C measured 1 hour post trip. * Device tested at 40 A. Physical characteristics Lead material Soldering characteristics Insulating material RUE090–250: Tin lead-plated copper-clad steel, 24 AWG, ∅ 0.51 mm/0.020 in RUE300–900: Tin lead-plated copper, 20 AWG, ∅ 0.81 mm/0.032 in Solderability per MIL-STD-202, Method 208E Solder heat withstand per MIL-STD-202, Method 210, Condition B Cured, flame-retardant epoxy polymer; meets UL 94V-O requirements Note: Devices are not designed to be placed through a reflow process. 146 RUE Devices Raychem Circuit Protection Devices RUE(7) 1/15/99 11:28 AM Page 147 RUE Radial Leaded Agency recognitions UL CSA ¨V TU File # E74889 File # CA78165C Certificate # R9477318 Environmental specifications Test Passive aging Test method Raychem PS300 Humidity aging Thermal shock Solvent resistance Raychem PS300 Raychem PS300 Raychem PS300, Method 215 Conditions 70°C, 1000 hours 85°C, 1000 hours 85°C, 85% R.H., 1000 hours 125°C, –55°C (10 times) MIL-STD-202, Method 215F Change resistance ±5% ±5% ±5% ±5% No change Component layouts The dimensions in the table below provide the component layout for each RUE device. Component layout dimensions (millimeters/inches) B A B Raychem Circuit Protection Devices Device RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 A nom. 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 5.1 (0.20) 10.2 (0.40) 10.2 (0.40) 10.2 (0.40) 10.2 (0.40) 10.2 (0.40) B max. 0.8 (0.03) 0.8 (0.03) 1.0 (0.04) 1.0 (0.04) 1.0 (0.04) 1.2 (0.05) 1.5 (0.06) 1.7 (0.07) 1.0 (0.04) 1.0 (0.04) 1.2 (0.05) 1.5 (0.06) 1.5 (0.06) RUE Devices 147 4 RUE(7) 1/15/99 11:28 AM Page 148 RUE Radial Leaded Tape and reel specifications (dimensions in millimeters) Product availability: RUE090–RUE400 Devices taped using EIA468-B/IEC286-2 standards. See table below and Figures 1 and 2 for details. 4 Dimension description Carrier tape width Hold down tape width: RUE090-RUE250 Top distance between tape edges Sprocket hole position Sprocket hole diameter* Abscissa to plane (straight lead) Abscissa to plane (kinked lead) Abscissa to top RUE090–185 Abscissa to top RUE250–400* Overall width w/lead protrusion RUE090–RUE250 Overall width w/lead protrusion RUE250 Overall width w/o lead protrusion RUE090–RUE185 Overall width w/o lead protrusion RUE300–RUE400* Lead protrusion Protrusion of cut out Protrusion beyond hold-down tape Sprocket hole pitch: RUE090–RUE250 Sprocket hole pitch on RUE300–RUE400 Device pitch: RUE090–RUE250 Device pitch: RUE300–RUE400 Pitch tolerance Tape thickness Tape thickness with splice RUE090-RUE250 Tape thickness with splice RUE300-RUE400* Splice sprocket hole alignment Body lateral deviation Body tape plane deviation Ordinate to adjacent component lead* Lead spacing: RUE090–RUE400* Reel width RUE090–RUE300 Reel width RUE400* Reel diameter Space between flanges less device* Arbor hole diameter Core diameter* Box Consecutive missing places Empty places per reel EIA mark W W4 W6 W5 D0 H H0 H1 IEC mark W W0 W2 W1 D0 H H0 H1 C1 C2 L1 L l2 P0 P0 l1 L l2 P0 P0 t t1 t1 t ∆h ∆p P1 F w2 w2 a w1 c n ∆h ∆p P1 F w w d f h Dimensions Dim. (mm) 18 11 3 9 4 18.5 16 32.2 35.4 43.2 43.9 42.5 44.2 1.0 11 Not specified 12.7 25.4 12.7 25.4 20 consec. 0.9 1.5 2.0 0 0 0 3.81 5.08 56 63.5 370 4.75 26 91 56/372/372 None 0.1% max. Tol. (mm) –0.5/+1.0 min. max. –0.5/+0.75 –0.32/+0.2 ±3.0 ±0.5 max. max. max. max. max. max. max. max. ±0.3 ±0.5 ±1 max. max. max. ±0.3 ±1.0 ±1.3 ±1.0 ±0.8 max. max. max. 3.25/+8.25 ±12.0 max. max. *Differs from EIA specification 148 RUE Devices Raychem Circuit Protection Devices RUE(7) 1/15/99 11:28 AM Page 149 RUE Radial Leaded Figure 1: EIA Referenced Taped Component Dimensions ∆h ∆p ∆h ∆p Reference plane P1 H1 H1 C1 H C2 F A L H0 B W4 W5 W I2 L1 D0 P0 Direction of unreeling Cross section A - B t 4 Figure 2: Reel Dimensions Reel Upper side n Tape a Direction of unreeling Lower side c w1 w2 Cross section Optional shape: Circular or polygonal Raychem Circuit Protection Devices RUE Devices 149 RUE(7) 1/15/99 11:28 AM Page 150 RUE Radial Leaded Ordering information Product description RUE090 RUE090-2 RUE090-AP RUE110 RUE110-2 RUE110-AP RUE135 RUE135-2 RUE135-AP RUE160 RUE160-2 RUE160-AP RUE185 RUE185-2 RUE185-AP RUE250 RUE250-2 RUE250-AP RUE300 RUE300-2 RUE300-AP RUE400 RUE400-2 RUE400-AP RUE500 RUE600 RUE700 RUE800 RUE900 4 Bag quantity 500 Tape and reel quantity AMMO pack 3000 2000 500 3000 2000 500 3000 2000 500 3000 2000 500 3000 2000 500 3000 2000 500 1500 1000 500 1500 500 500 500 500 500 * * * * * 1000 * * * * * Standard package 10000 15000 10000 10000 15000 10000 10000 15000 10000 10000 15000 10000 10000 15000 10000 10000 15000 10000 10000 7500 5000 10000 7500 5000 10000 10000 10000 10000 10000 *Consult Factory Part numbering system RUE suffix Blank = Packaged in bags = Tape and reel -AP = AMMO pack -1 = 25.4-mm (1.0-inch) minimum lead length -2 K S U = Kinked leads = Straight leads = Uncoated part (contact factory for specifications) Current rating 150 RUE Devices Raychem Circuit Protection Devices RUE(7) 1/15/99 11:28 AM Page 151 RUE Radial Leaded Part marking system V V V 30 U135 NJ2K V - 30 Voltage rating Raychem symbol U Part ID Product family (RUE) Example Lot number/Date code (may be on the back) Part description RUE090 RUE110 RUE135 RUE160 RUE185 RUE250 RUE300 RUE400 RUE500 RUE600 RUE700 RUE800 RUE900 Part ID 090 110 135 160 185 250 300 400 500 600 700 800 900 4 WARNING: • Operation beyond maximum ratings or improper use may result in device damage and possible electrical arcing and flame. • These devices are intended for protection against occasional overcurrent or overtemperature fault conditions, and should not be used when repeated fault conditions are anticipated. • Operation in circuits with inductive spikes can generate voltages above the rated voltage of the devices and should be evaluated for suitability of use. Raychem Circuit Protection Devices RUE Devices 151