S6006NS3TP

Thyristors 6 Amp Sensitive & Standard SCRs Sxx06xSx & Sxx06x Series RoHS Description This Sxx06x SCR series is ideal for uni-directional switch applications such as phase control, heating, motor speed controls, converters/rectifiers and capacitive discharge ignitions. These SCRs have a low gate current trigger level of 0.2 to 15 mA at approximately 1.5V, with a sensitive version of this series having a gate trigger current less than 500µA. The sensitive gate SCR version is easily triggered by sense coils, proximity switches, and microprocessors. Agency Approval Features & Benefits Agency Agency File Number E71639* * - L Package Only • Halogen free and RoHS compliant •S  urge capability up to 100 A at 60 Hz half cycle • Glass – passivated junctions • L-Package is UL recognized for 2500Vrms • Voltage capability up to 1000 V Main Features Applications Symbol Value Unit A IT(RMS) 6 VDRM / VRRM 400 to 1000 V IGT 0.2 to 15 mA Typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. Also, AC control & rectification for power tools, home/ brown goods and white goods appliances and 2-wheeler rectifier/battery regulators. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol Additional Information Datasheet Resources Samples A K G ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Absolute Maximum Ratings — Sensitive SCRs Symbol IT(RMS) IT(AV) ITSM Parameter Test Conditions RMS on-state current Average on-state current Peak non-repetitive surge current Sxx06LSy TC = 80°C Sxx06NSy Sxx06RSy Sxx06DSy Sxx06VSy TC = 95°C Sxx06LSy TC = 80°C Sxx06NSy Sxx06RSy Sxx06DSy Sxx06VSy TC = 95°C Value Unit 6 A 3.8 A single half cycle; f = 50Hz; TJ (initial) = 25°C 83 single half cycle; f = 60Hz; TJ (initial) = 25°C 100 A I2t I2t Value for fusing tp = 8.3 ms 41 A2s di/dt Critical rate of rise of on-state current f = 60Hz; TJ = 110°C 100 A/μs IGTM Peak gate current TJ = 110°C 1 A PG(AV) Average gate power dissipation TJ = 110°C 0.1 W Tstg Storage temperature range -40 to 150 °C TJ Operating junction temperature range -40 to 110 °C Value Unit 6 A 3.8 A Note: xx = voltage, y = sensitivity Absolute Maximum Ratings — Standard SCRs Symbol IT(RMS) IT(AV) ITSM Parameter RMS on-state current Average on-state current Peak non-repetitive surge current Sxx06L TC = 100°C Sxx06N Sxx06R Sxx06D Sxx06V TC = 110°C Sxx06L TC = 100°C Sxx06N Sxx06R Sxx06D Sxx06V TC = 110°C single half cycle; f = 50Hz; TJ (initial) = 25°C 83 single half cycle; f = 60Hz; TJ (initial) = 25°C 100 A I 2t I2t value for fusing tp = 8.3 ms 41 A2s di/dt Critical rate-of-rise of on-state current f = 60Hz; TJ =125°C 100 A/μs IGTM Peak gate current TJ = 125°C 2 A PG(AV) Average gate power dissipation TJ = 125°C 0.5 W Tstg Storage temperature range -40 to 150 °C TJ Operating junction temperature range -40 to 125 °C Note: xx = voltage ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Sensitive SCRs Symbol Value Test Conditions Sxx06xS2 Sxx06xS3 Unit IGT VD = 6V RL = 100 Ω MAX. VGT VD = 6V RL = 100 Ω MAX. 0.8 V VD = VDRM; RGK = 1kΩ; TJ = 110°C TYP. 8 V/μs VGD VD = VDRM RL = 3.3 kΩ TJ = 110°C MIN. 0.2 V VGRM IGR = 10μA MIN. 6 IH IT = 20mA (initial) MAX. 6 8 mA tq IT = 2A; tp= 50µs; dv/dt=5V/µs; di/dt=-30A/µs MAX. 50 45 μs tgt IG = 2 x IGT PW = 15µs IT = 12A TYP. 4 5 μs dv/dt 200 500 μA V Note: xx = voltage, x = package Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Standard SCRs Symbol Value Test Conditions Sxx06x Unit IGT VD = 12V RL = 60 Ω MAX. 15 mA VGT VD = 12V RL = 60 Ω MAX. 1.5 V VD = VDRM; gate open; TJ = 100°C dv/dt 400V 350 600V 300 800V 1000V 250 MIN. 400V VD = VDRM; gate open; TJ = 125°C VGD 100 V/μs 250 600V 225 800V 200 VD = VDRM RL = 3.3 kΩ TJ = 125°C MIN. 0.2 V IH IT = 200mA (initial) MAX. 30 mA tq IT = 2A; tp= 50µs; dv/dt=5V/µs; di/dt=-30A/µs MAX. 35 μs tgt IG = 2 x IGT PW = 15µs IT = 12A TYP. 2 μs Note: xx = voltage, x = package ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Static Characteristics Symbol Test Conditions VTM IT = 12A; tp = 380 µs Sxx06xyy IDRM / IRRM TJ = 25°C TJ = 110°C TJ = 25°C VDRM = VRRM Sxx06x TJ = 100°C TJ = 125°C MAX. Value Unit 1.6 V 400 – 600V 5 400 – 600V 250 400 – 800V 1000V 10 MAX. μA 20 400 – 800V 200 1000V 3000 400 – 800V 500 Note: xx = voltage, x = package, yy = sensitivity Thermal Resistances Symbol Rθ(J-C) Rθ(J-A) Parameter Junction to case (AC) Junction to ambient Value Sxx06RSy / Sxx06NSy 2.6 Sxx06LSy 4.3 Sxx06VSy 2.4 Sxx06DSy 1.8 Sxx06R / Sxx06N 2.5 Sxx06L 4.0 Sxx06V 2.3 Sxx06D 1.7 Sxx06RSy 40 Sxx06LSy 65 Sxx06VSy 85 Sxx06R 40 Sxx06L 50 Sxx06V 70 Unit °C/W °C/W Note: xx = voltage, y = sensitivity ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature (Sensitive SCR) Figure 2: N  ormalized DC Gate Trigger Current vs. Junction Temperature (Standard SCR) 4.0 Ratio of IGT / IGT (TJ = 25ºC) Ratio of IGT /IGT (TJ=25ºC) 4.0 3.0 2.0 3.0 2.0 1.0 1.0 0.0 0.0 -40 -15 10 85 60 35 -40 -15 110 110 125 110 125 Figure 4: N  ormalized DC Holding Current vs. Junction Temperature 2.0 Ratio of IH / IH (TJ = 25ºC) 2.0 Ratio of VGT / VGT (TJ = 25ºC) 85 60 Junction Temperature (TJ) - (ºC) Junction Temperature (TJ) - (ºC) Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature 35 10 1.5 1.0 0.5 0.0 -40 -15 60 35 10 110 85 125 1.5 1.0 0.5 0.0 -40 -15 Junction Temperature (TJ) - (ºC) 35 10 85 60 Junction Temperature (TJ) - (ºC) Figure 5: On-State Current vs. On-State Voltage (Typical) Figure 6: P  ower Dissipation (Typical) vs. RMS On-State Current 6 30 TJ= 25°C 5 Average On-State Power Dissipation [PD(AV)] - (Watts) Instantaneous On-State Current (iT) -Amps 25 20 15 10 5 4 3 2 1 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 Instantaneous On-State Voltage (vT) - Volts 1.5 1.6 0 0 1 2 3 4 5 6 RMS On-State Current [IT(RMS)] - (Amps) ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Figure 7: Maximum Allowable Case Temperature vs. RMS On-State Current Figure 8: M  aximum Allowable Case Temperature vs. Average On-State Current 130 130 Sxx06R/Sxx06N Sxx06R Sxx06D Sxx06V 120 Sxx06RSy/ Sxx06NSy Sxx06RSy 115 Sxx06DSy 110 Sxx06L 105 100 95 90 Sxx06LSy CURRENT WAVEFORM: Sinsuoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 85 1 2 Sxx06D Sxx06V 120 Sxx06RSy/ Sxx06NSy Sxx06RSy 115 Sxx06DSy Sxx06VSy 110 Sxx06L 105 100 95 90 CURRENT WAVEFORM: Sinsuoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 85 80 0 Sxx06R/Sxx06N Sxx06R 125 Maximum Allowable Case Temperature (TC) - ºC Maximum Allowable Case Temperature (TC) - º C 125 3 4 5 6 80 7 0 1 RMS On-State Current [IT(RMS)] - Amps Sxx06L 80 Sxx06LSy Sxx06RSy 4 Figure 10: Maximum Allowable Ambient Temperature vs. Average On-State Current Maximum Allowable Ambient Temperature (TA) - ºC Maximum Allowable Temperature (TA) - ºC 100 3 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Sxx06R 2 Average On-State Current [IT(AVE)] - Amps Figure 9: Maximum Allowable Ambient Temperature vs. RMS On-State Current 120 Sx06LSy Sxx06V 60 40 Sxx06VSy 20 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Sxx06R 100 80 60 Sxx06L Sxx06RSy Sxx06LSy Sxx06V 40 Sxx06VSy 20 0 0 0.0 0.5 1.0 1.5 2.0 0.0 2.5 0.5 RMS On-State Current [IT(RMS)] - Amps 1.0 1.5 Average On-State Current [IT(AVE)] - Amps Note: xx = voltage, y = sensitivity Figure 12: P  eak Capacitor Discharge Current Derating Figure 11: Peak Capacitor Discharge Current 1.2 Normalized Peak Current Peak Discharge Current (ITM) - Amps 1000 100 ITRM 1.0 0.8 0.6 0.4 Sensitive SCR Standard SCR 0.2 tW 10 0.5 1.0 10 .0 Pulse Current Duration (tw) - ms 50.0 0.0 0 25 50 75 100 125 150 Case Temperature (TC) - ºC ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Figure 13-1: Typical DC Gate Trigger Current with RGK vs. Junction Temperature for S6008DS2 Figure 13-2: Typical DC Gate Trigger Current with RGK vs. Junction Temperature for SS6008DS3 Figure 14-1: Typical DC Holding Current with RGK vs. Junction Temperature for S6008DS2 Figure 14-2 Typical DC Holding Current with RGK vs. Junction Temperature for SS6008DS3 Figure 15-1: Typical Static dv/dt with RGK vs. Junction Temperature for S6008DS2 Figure 15-2 Typical Static dv/dt with RGK vs. Junction Temperature for SS6008DS3 ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Figure 16-1: Typical Static dv/dt with RGK vs. Junction Temperature for S6008DS2 Figure 16-2 Typical Static dv/dt with RGK vs. Junction Temperature for SS6008DS3 Figure 17: S  urge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-State Current (ITSM) – AMPS 100 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature 10 1 Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 1 10 100 1000 Surge Current Duration -- Full Cycles ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability rating 94V-0 Lead Material Copper Alloy tP TP Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 Ramp-do Ramp-down tS time to peak temperature Time Design Considerations Careful selection of the correct component for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Environmental Specifications Test Specifications and Conditions AC Blocking MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours Temperature Cycling MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time Temperature/Humidity EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity High Temp Storage MIL-STD-750, M-1031, 1008 hours; 150°C Low-Temp Storage 1008 hours; -40°C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Product Selector Part Number Voltage Gate Sensitivity Type Package - 0.2mA Sensitive SCR TO-220R - 0.2mA Sensitive SCR TO-220L - - 0.2mA Sensitive SCR TO-251 X - - 0.2mA Sensitive SCR TO-252 X X - - 0.5mA Sensitive SCR TO-220R Sxx06LS3 X X - - 0.5mA Sensitive SCR TO-220L Sxx06VS3 X X - - 0.5mA Sensitive SCR TO-251 Sxx06DS3 X X - - 0.5mA Sensitive SCR TO-252 Sxx06R X X X X 15mA Standard SCR TO-220R TO-220L 400V 600V 800V 1000V Sxx06RS2 X X - Sxx06LS2 X X - Sxx06VS2 X X Sxx06DS2 X Sxx06RS3 Sxx06L X X X X 15mA Standard SCR Sxx06V X X X X 15mA Standard SCR TO-251 Sxx06D X X X X 15mA Standard SCR TO-252 Note: xx = voltage ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Dimensions — TO-251AA (V/I-Package) — V/I-PAK Through Hole TC MEASURING POINT E Anode H D AREA: 0.040 IN2 Dimension 5.28 .208 J A 5.34 .210 B R P Q S K C Cathode L F Anode GATE G Inches Millimeters Min Typ Max Min Typ A 0.037 0.040 0.043 0.94 1.01 Max 1.09 B 0.235 0.242 0.245 5.97 6.15 6.22 C 0.350 0.361 0.375 8.89 9.18 9.53 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.66 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.34 2.41 I 0.176 0.180 0.184 4.47 4.57 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.52 0.58 P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 R 0.034 0.039 0.044 0.86 1.00 1.11 S 0.074 0.079 0.084 1.86 2.00 2.11 I Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount Anode E D 6.71 .264 5.28 .208 TC MEASURING POINT Dimension A 6.71 .264 5.34 .210 B 1.60 .063 P Q C 1.80 .071 GATE F Cathode Anode AREA : 0.040 IN2 3 .118 G I O L K M N J H 4.60 .181 Inches Millimeters Min Typ Max Min Typ A 0.037 0.040 0.043 0.94 1.01 Max 1.09 B 0.235 0.243 0.245 5.97 6.16 6.22 C 0.106 0.108 0.113 2.69 2.74 2.87 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.65 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.33 2.41 I 0.176 0.179 0.184 4.47 4.55 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.51 0.58 M 0.000 0.000 0.004 0.00 0.00 0.10 N 0.021 0.026 0.027 0.53 0.67 0.69 O 0° 0° 5° 0° 0° 5° P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT AREA (REF.) 0.17 IN2 Dimension O A E 8.13 .320 P A ANODE B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M J Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 2.92 B 0.105 0.115 2.67 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Min Max Min Max 0.380 0.420 9.65 10.67 2.92 Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab TC MEASURING POINT O A E P AREA (REF.) 0.17 IN2 Dimension 8.13 .320 A Inches Millimeters B 0.105 0.115 2.67 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L L 0.060 0.075 1.52 1.91 H M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 B C 13.36 .526 D 7.01 .276 F R G CATHODE ANODE GATE K J N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs Dimensions — TO-263 (N Package) — D2Pak Surface Mount Dimension Inches Millimeters Min Max Min A 0.360 0.370 9.14 Max 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 D 0.025 0.035 0.64 0.89 E 0.045 0.060 1.14 1.52 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.092 0.102 2.34 2.59 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.88 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx06L/RyyTP Sxx06L/Ryy 2.2 g Tube 1000 (50 per tube) 750 (75 per tube) Sxx06DyyTP Sxx06Dyy 0.3 g Tube Sxx06DyyRP Sxx06Dyy 0.3 g Embossed Carrier 2500 Sxx06VyyTP Sxx06Vyy 0.4 g Tube 750 (75 per tube) Sxx06L/RTP Sxx06L/R 2.2 g Tube 1000 (50 per tube) Sxx06DTP Sxx06D 0.3 g Tube 750 (75 per tube) Sxx06DRP Sxx06D 0.3 g Embossed Carrier 2500 Sxx06VTP Sxx06V 0.4 g Tube 750 (75 per tube) Sxx06NyyRP Sxx6Nyy 1.6g Embossed Carrier 500 Sxx06NyyTP Sxx6Nyy 1.6g Tube 1000 (50 per tube) Sxx06NRP Sxx6N 1.6g Embossed Carrier 500 Sxx06NTP Sxx6N 1.6g Tube 1000 (50 per tube) Note: xx = Voltage/10; yy = Sensitivity ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 6 Amp Sensitive & Standard SCRs TO-252 Embossed Carrier Reel Pack (RP) Specs TO-202 Type 1 (F Package) TO-251 TO-252 Part Marking System S6006F1 Meets all EIA-481-2 Standards 0.157 (4.0) Gate 0.059 DIA (1.5) TO-251AA- (V Package) yxxxx TO-252AA- (D Package) ® Cathode ® YMLDD * Cover tape 0.512 (13.0) Arbor Hole Diameter 0.315 (8.0) YMLDD ® Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code Anode 12.99 (330.0) S6006DS2 XXXXXX DC XX XXXXXX DC XX XXXXXX * DC 0.524 (13.3) XX 0.63 (16.0) XXXXXX S6006DS2 ® TO-263 AA - (N Package) TO-220 AB - (L and R Package) Dimensions are in inches (and millimeters). S6006RS2 YMXXX ® 0.64 (16.3) Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Direction of Feed Part Numbering System S 60 06 L S2 56 COMPONENT S: SCR VOLTAGE RATING 40: 400V 60: 600V 80: 800V K0: 1000V CURRENT RATING 06: 6A LEAD FORM DIMENSIONS xx: Lead Form Option SENSITIVITY & TYPE Sensitive SCR: S2: 200µA S3: 500µA Standard SCR: (blank): 15mA PACKAGE TYPE L: TO-220 Isolated R: TO-220 Non-Isolated V: TO-251 (V/I-Pak) D: TO-252 (D-Pak) N: TO 263 (D2 Pak) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20