S6040RTP

Thyristors 40 Amp Standard SCRs Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits • RoHS compliant • Glass – passivated junctions Main Features • Voltage capability up to 1000 V • Surge capability up to 520 A Applications Symbol Value Unit IT(RMS) 40 A VDRM / VRRM 400 to 1000 V IGT 40 mA Typical applications are AC solid-state switches, industrial power tools, exercise equipment, white goods and commercial appliances. Schematic Symbol A K G Absolute Maximum Ratings Symbol Parameter Test Conditions Value Unit IT(RMS) RMS on-state current TC = 100°C 40 A IT(AV) Average on-state current A ITSM Peak non-repetitive surge current TC = 100°C 25.0 single half cycle; f = 50Hz; TJ (initial) = 25°C 430 single half cycle; f = 60Hz; TJ (initial) = 25°C 520 A I2t I2t Value for fusing tp = 8.3 ms 1122 A2s di/dt Critical rate of rise of on-state current f = 60Hz ; TJ = 125°C 175 A/μs IGM Peak gate current TJ = 125°C 3.5 A PG(AV) Average gate power dissipation TJ = 125°C 0.8 W Tstg Storage temperature range -40 to 150 °C TJ Operating junction temperature range -40 to 125 °C © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol Test Conditions IGT Value VD = 12V; RL = 30 Ω MAX. 40 MIN. 5 MAX. VGT VD = VDRM; gate open; TJ = 100°C 650 600V 600 1000V VD = VDRM; gate open; TJ = 125°C mA 1.5 400V 800V dv/dt Unit V 500 250 MIN. 400V 550 600V 500 800V V/μs 475 VGD VD = VDRM; RL = 3.3 kΩ; TJ = 125°C MIN. 0.2 V IH IT = 400mA (initial) MAX. 60 mA tq (1) MAX. 35 μs tgt IG = 2 x IGT; PW = 15µs; IT = 80A TYP. 2.5 μs Note : 1. IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs Static Characteristics Symbol Test Conditions IT = 80A; tp = 380μs VTM TJ = 25°C IDRM / IRRM VDRM / VRRM TJ = 100°C TJ = 125°C MAX. Value Unit 1.8 V 400 – 600V 10 800 V 20 1000 V 30 400 – 600V 1000 800V MAX. 1500 1000V 5000 400 – 600V 2000 800V 3000 μA Thermal Resistances Symbol Value Unit RƟ(JC) Junction to case (AC) Parameter Sxx40R / Sxx40N 0.6 °C/W RƟ(J-A) Junction to ambient Sxx40R 40 °C/W © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: N  ormalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25°C) Ratio of IGT / IGT (TJ = 25°C) 2.0 1.5 1.0 0.5 1.5 1.0 0.5 0.0 0.0 -40 -15 10 35 60 85 110 -40 125 -15 10 35 60 85 110 125 Junction Temperature (TJ ) --(°C) Junction Temperature (TJ)-- (°C) Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: O  n-State Current vs. On-State Voltage (Typical) 120 2.0 TJ = 25°C 1.5 Instantaneous On-state Current (iT) – Amps Ratio of IH / IH (TJ = 25°C) 100 1.0 0.5 80 60 40 20 0.0 -40 -15 10 35 60 85 110 0 125 0.7 0.8 Junction Temperature (T J) -- (°C) Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Figure 6: M  aximum Allowable Case Temperature vs. RMS On-State Current 40 130 125 35 120 Maximum Allowable Case Temperature (TC )- °C Average On-State Power Dissipation [PD(AV)] - (Watts) 0.9 Instantaneous On-state Voltage (vT) – Volts 30 25 20 15 10 115 110 105 100 95 90 85 80 5 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 75 0 0 5 10 15 20 25 30 RMS On-State Current [IT(RMS)] - (Amps) 35 40 70 0 5 10 15 20 25 30 35 40 45 50 RMS On-State Current [IT(RMS)] - Amps © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Figure 8: Maximum Allowable Ambient Temperature vs. RMS On-State Current 130 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Maximum Allowable Ambient Temperature (TA) - °C Maximum Allowable Case Temperature (TC) - °C 125 120 115 110 105 100 95 90 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 85 100 80 60 40 20 0 80 0 5 10 15 20 25 0.0 0.5 1.0 1.5 2.0 2.5 RMS On-State Current [IT(RMS)] - Amps Average On-State Current [IT(AVE)] - Amps Figure 9: Maximum Allowable Ambient Temperature vs. Average On-State Current Maximum Allowable Ambient Temperature (Tc) - °C 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 100 80 60 40 20 0 0.0 0.5 1.0 1.5 Average On-State Current [IT(AVE)] - Amps Figure 10: Peak Capacitor Discharge Current Figure 11: Peak Capacitor Discharge Current Derating 1.2 1.0 Normalized Peak Current Peak Discharge Current (ITM) - Amps 10000 1000 ITRM 0.8 0.6 0.4 0.2 tW 100 0.0 0.5 1.0 10.0 Pulse Current Duration (tw) - ms 50.0 0 25 50 75 100 125 150 Case Temperature (TC) - °C © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Figure 12: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 Supply Frequency: 60 Hz Sinusoidal Load: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 10 100 1000 Surge Current Duration -- Full Cycles Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C tP TP Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 Ramp-do Ramp-down tS time to peak temperature Time © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Physical Specifications Environmental Specifications Terminal Finish 100% Matte Tin-plated Body Material UL recognized compound meeting flammability rating V-0. Lead Material Copper Alloy Test Specifications and Conditions AC Blocking Temperature Cycling Design Considerations Careful selection of the correct component for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Temperature/Humidity High Temp Storage Low-Temp Storage Resistance to Solder Heat Solderability MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C 1008 hours; -40°C MIL-STD-750 Method 2031 ANSI/J-STD-002, category 3, Test A MIL-STD-750, M-2036 Cond E Lead Bend Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC Measuring Point Dimension O A E Area (REF.) 0.17 IN2 8.13 .320 P A Anode B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H Cathode Anode K J Gate N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 2.92 B 0.105 0.115 2.67 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Dimensions – TO- 263 (N-package) — D2-Pak Surface Mount TC Measuring Point B Area: 0.11 in C V 2 Dimension 8.41 .331 Min A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 0.025 0.035 0.63 0.89 E 0.048 0.055 1.22 1.40 U F 0.060 0.075 1.52 1.91 J G 0.095 0.105 2.41 2.67 H 0.083 0.093 2.11 2.36 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.87 S K Gate Cathode G 8.13 .320 H D F 11.68 .460 2.16 .085 7.01 .276 Max D 7.01 .276 A W Millimeters Max E Anode Inches Min 7.01 .276 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 16.89 .665 8.89 .350 1.40 .055 3.81 .150 2.03 .080 6.60 .260 Part Numbering System S 60 40 R Device Type S: SCR Voltage Rating 40: 400V 60: 600V 80: 800V K0: 1000V Part Marking System 56 TO-220 AB - (R Package) TO-263 AB - (N Package) Lead Form Dimensions xx: Lead Form Option Sensitivity Type [blank]: 40mA S6040R YM ® Currenting Rating 40: 40A Package Type R: TO-220 (Non-isolated) 2 - Pak) N: TO-263 (D Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20 Thyristors 40 Amp Standard SCRs Product Selector Part Number Voltage 400V 600V 800V Gate Sensitivity 1000V Type Package Sxx40R X X X X 40mA Standard SCR TO-220R Sxx40N X X X X 40mA Standard SCR TO-263 Note: xx = Voltage Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx40RTP Sxx40R 2.2g Tube 1000 (50 per tube) Sxx40NTP Sxx40N 1.6g Tube 1000 (50 per tube) Sxx40NRP Sxx40N 1.6g Embossed Carrier 500 Note: xx = Voltage Reel Pack (RP) for TO-263 Embossed Carrier Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DI A (1.5) 0.945 (24.0) 0.827 (21.0) Cathode * * Co ver tape Anode 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of F eed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/15/20