SJ6025N2RP

Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs SJxx25xx Series RoHS Description This SJxx25xx high temperature SCR series is ideal for uni-directional switch applications such as phase control in heating, motor speed controls, converters/rectifiers and inrush current controllers. These SCRs have a low gate current trigger level of 6mA,10mA or 35mA maximum at approximately 1.5V Features & Benefits • Halogen free and RoHS compliant • Surge capability up to 350 A at 60 Hz half cycle • 150°C maximum junction temperature Schematic Symbol Applications A K G Typical applications include AC Generator (ACG) rectifiers, battery voltage regulators, generic converters, inrush current controller in various AC to DC applications and soft starter for low power AC motor. Additional applications include controls for power tools, home/brown good and white goods appliances. Isolated packages offered for ease of heat sinking. Agency Approval Main Features Agency Symbol Agency File Number L Packages: E71639 Value Unit IT(RMS) 25 A VDRM / VRRM 400 or 600 V IGT 6,10, to 35 mA Absolute Maximum Ratings Symbol VDRM/VRSM Parameter Test Conditions Value Unit Peak non-repetitive blocking voltage Pw=100 μs VDRM/VRRM+100 V 25 A 16 A SJxx25Lx RMS on-state current IT(RMS) TC = 100°C SJxx25Rx TC = 125°C SJxx25Nx TC = 100°C SJxx25Lx Average on-state current IT(AV) SJxx25Rx TC = 125°C SJxx25Nx single half cycle; f = 50Hz; TJ (initial) = 25°C 300 single half cycle; f = 60Hz; TJ (initial) = 25°C 350 A ITSM Peak non-repetitive surge current I2t I2t Value for fusing tp = 8.3 ms 510 A 2s Critical rate of rise of on-state current f = 60Hz ; TJ = 150°C 125 A/μs Peak gate current TJ = 150°C 3 A Average gate power dissipation TJ = 150°C di/dt IGM PG(AV) 0.6 W Tstg Storage temperature range -40 to 150 °C TJ Operating junction temperature range -40 to 150 °C Note: xx=voltage/10, x=sensitivity SJxx25xx Series Sxx20x & Sxx25x Series ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp 25 HighStandard JunctionSCRs Temperature SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol Value Test Conditions IGT VD = 12V RL = 60 Ω VGT VD = 12V RL = 60 Ω SJxx25x SJxx25x2 MAX. 35 6 10 MIN. 8 2 5 MAX. VD = 67% VDRM; gate open; TJ = 125°C dv/dt SJxx25x1 mA 1.5 MIN. VD = 67% VDRM; gate open; TJ = 150°C Unit V 800 70 500 400 - 200 V/μs VGD VD = VDRM RL = 3.3 kΩ TJ = 125°C MIN. IH IT = 400mA (initial) MAX. tq IT = 2A; tp = 50µs; dv/dt = 5V/µs; di/dt = 30A/µs MAX. 40 μs tgt IG = 2 x IGT PW = 15µs IT = 50A TYP. 2 μs 0.2 75 V 15 35 mA Note: xx=voltage/10, x=package Static Characteristics Symbol Test Conditions Component IT = 50A; tp = 380 µs VTM MAX. TJ = 25°C IDRM / IRRM Unit 1.6 V 10 TJ = 125°C VDRM = VRRM Value 1000 MAX. TJ = 150°C μA 3000 Thermal Resistances Symbol Parameter Value Junction to case (AC) Rθ(JC) SJxx25Rx SJxx25Nx 1.0 SJxx25Lx 2.3 Unit °C/W Note: xx=voltage/10, x=sensitivity Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: N  ormalized DC Gate Trigger Voltage vs. Junction Temperature 1.4 1.6 Ratio of VGT / VGT (TJ = 25ºC) Ratio of IGT / IGT (TJ = 25°C) 2.0 1.2 0.8 0.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.0 -40 -15 10 35 60 Junction Temperature (TJ) -- (ºC) SJxx25xx Series Sxx20x & Sxx25x Series 85 110 135 150 -40 -15 10 35 60 85 110 135 150 Junction Temperature (TJ) -- (°C) ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: O  n-State Current vs. On-State Voltage (Typical) Intantaneous On-state Current (iT) – Amps 60 Ratio of IH / IH (TJ = 25°C) 2.0 1.6 1.2 0.8 0.4 T J = 25°C 50 40 30 20 10 0 0.0 -40 -15 10 35 60 85 110 135 0.6 150 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Instantaneous On-state Voltage (vT) – Volts Junction Temperature (TJ) -- (°C) Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Figure 6: M  aximum Allowable Case Temperature vs. RMS On-State Current 150 SJxx25Rx SJxx25Nx 140 20 Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation [PD(AV)] - (Watts) 25 15 10 5 130 SJxx25Lx 120 110 100 90 80 0 0 5 10 15 20 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 25 70 RMS On-State Current [IT(RMS)] - (Amps) 0 5 10 15 20 25 30 RMS On-State Current [IT(RMS)] - Amps Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Figure 8: Peak Capacitor Discharge Current 150 1000 Maximum Allowable Case Temperature (TC) - °C 130 Peak Discharge Current (ITM) - Amps SJxx25Rx SJxx25Nx 140 SJxx25Lx 120 110 100 90 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 80 100 ITRM tW 70 10 0 5 10 Average On-State Current [IT(AVE)] - Amps SJxx25xx Series Sxx20x & Sxx25x Series 15 18 0.5 1.0 10.0 50.0 Pulse Current Duration (tW) - ms ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs Figure 9: Peak Capacitor Discharge Current Derating 1.2 Normalized Peak Current 1.0 0.8 0.6 0.4 0.2 0.0 0 25 50 75 100 125 150 Case Temperature (TC) - ºC Figure 10: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive)On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. G  ate control may be lost during and immediately following surge current interval. 2. O  verload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 10 100 1000 Surge Current Duration -- Full Cycles SJxx25xx Series Sxx20x & Sxx25x Series ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish Ramp-up TL tL TS(max) Preheat TS(min) 100% Matte Tin-plated 25 Ramp-do Ramp-down tS 217°C 60 – 150 seconds - Time (tL) tP TP Temperature Reflow Condition time to peak temperature Time Environmental Specifications Test Body Material UL Recognized compound meeting flammability rating V-0. AC Blocking Lead Material Copper Alloy Temperature Cycling Temperature/ Humidity Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 150°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -55°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 160V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C Design Considerations High Temp Storage Careful selection of the correct component for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage 1008 hours; -40°C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Moisture Sensitivity Level Level 1, JEDEC-J-STD-020D SJxx25xx Series Sxx20x & Sxx25x Series ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT AREA (REF.) 0.17 IN2 O A E Dimension 8.13 .320 P ANODE A B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M J Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab TC MEASURING POINT O A E P AREA (REF.) 0.17 IN2 Dimension 8.13 .320 A B C 13.36 .526 D 7.01 .276 F R G L H CATHODE ANODE GATE K J SJxx25xx Series Sxx20x & Sxx25x Series Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). N M Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs Dimensions –TO- 263AB (N-package) — D2-Pak Surface Mount TC MEASURING POINT B AREA: 0.11 in 2 C V Dimension E ANODE A B C D E F G H J K S V U W 8.41 .331 7.01 .276 A S W U K GATE CATHODE G J 8.13 .320 H D F 11.68 .460 2.16 .085 7.01 .276 7.01 .276 16.89 .665 8.89 .350 1.40 .055 Inches Millimeters Min Max Min Max 0.360 0.380 0.178 0.025 0.045 0.060 0.095 0.092 0.018 0.090 0.590 0.035 0.002 0.040 0.370 0.420 0.188 0.035 0.060 0.075 0.105 0.102 0.024 0.110 0.625 0.045 0.010 0.070 9.14 9.65 4.52 0.64 1.14 1.52 2.41 2.34 0.46 2.29 14.99 0.89 0.05 1.016 9.40 10.67 4.78 0.89 1.52 1.91 2.67 2.59 0.61 2.79 15.88 1.14 0.25 1.78 3.81 .150 2.03 .080 6.60 .260 Product Selector Part Number Voltage 400V Gate Sensitivity 600V Type Package SJxx25L X X 35mA Standard SCR TO-220L SJxx25R X X 35mA Standard SCR TO-220R SJxx25N X X 35mA Standard SCR TO-263 SJxx25L1 X X 6mA Standard SCR TO-220L SJxx25R1 X X 6mA Standard SCR TO-220R SJxx25N1 X X 6mA Standard SCR TO-263 SJxx25L2 X X 10mA Standard SCR TO-220L SJxx25R2 X X 10mA Standard SCR TO-220R SJxx25N2 X X 10mA Standard SCR TO-263 Note: xx = Voltage/10 Packing Options Part Number Marking Weight Packing Mode Base Quantity SJxx25LxTP SJxx25Lx 2.2g Tube 500 (50 per tube) SJxx25RxTP SJxx25Rx 2.2g Tube 500 (50 per tube) SJxx25NxTP SJxx25Nx 1.6g Tube 500 (50 per tube) SJxx25NxRP SJxx25Nx 1.6g Embossed Carrier 500 Note: xx=voltage/10, x=sensitivity SJxx25xx Sxx20x &Series Sxx25x Series ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18 Thyristors 20 Amps / 25 Amp Standard 25 High JunctionSCRs Temperature SCRs TO-263 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DIA (1.5) 0.945 (24.0) 0.827 (21.0) Cathode * * Cover tape Anode 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed Part Numbering System Part Marking System TO-220 AB - (L and R Package) TO-263 AB - (N Package) SJ 60 25 R 1 TP COMPONENT TYPE SJ: high temperature SCR VOLTAGE RATING 40: 400V 60: 600V CURRENT RATING 25: 25A PACKING TYPE TP: Tube Pack RP: Reel Pack SENSITIVITY & TYPE [bank]:35mA 1: 6mA 2:10mA PACKAGE TYPE L: TO-220 Isolated R: TO-220 Non-Isolated N: TO-263 (D2-Pak) Sxx16R SJ6025R1 YM ® Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. SJxx25xx Series Sxx20x & Sxx25x Series ©2018 Littelfuse, Inc Specifications are subject to change without notice. Revised: 07/25/18