SJ6040R2TP

Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 SJxx40x Series RoHS Description This SJxx40x high temperature SCR series is ideal for uni-directional switch applications such as phase control in heating, motor speed controls and AC rectifier and voltage regulator. These SCRs have a low gate current trigger level of 40 mA maximum at approximately 1.5 V, with a sensitive version of this series having a gate trigger current of 15 mA maximum. Features & Benefits • High junction temperature • Voltage capability up to 600 V Main Features Symbol IT(RMS) VDRM /VRRM IGT Value Unit 40 A 400 or 600 V 40 mA •S  urge capability up to 520 A at 60 Hz half cycle •H  alogen free and RoHS compliant Applications Typical applications are AC rectifier, voltage regulator, AC solid-state switches, industrial power tools, exercise equipment, white goods and commercial appliances. Schematic Symbol A K G Absolute Maximum Ratings Symbol VDSM/VRSM Parameter Test Conditions Value Unit Peak non-repetitive blocking voltage Pw = 100μs 700 V IT(RMS) RMS on-state current TC = 120°C 40 A IT(AV) Average on-state current TC = 120°C 25.0 A single half cycle; f = 50Hz; TJ (initial) = 25°C 430 single half cycle; f = 60Hz; TJ (initial) = 25°C 520 I2t Value for fusing tp = 8.3 ms 1122 A2s Critical rate of rise of on-state current f = 60Hz ; TJ = 150°C 150 A/μs Peak gate current tp ≤ 10μs ; TJ = 150°C 4 A Average gate power dissipation tp ≤ 10μs ; TJ = 150°C 1 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 150 °C ITSM I 2t di/dt IGM PG(AV) Tstg TJ SJxx40x Series Sxx40x Series Peak non-repetitive surge current A ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17 Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol Test Conditions IGT VD = 12V; RL = 30 Ω VGT SJxx40x SJxx40x2 MAX. 40 15 MIN. 5 3 MAX. 600V dv/dt MIN. 400V VD = VDRM; gate open; TJ = 150°C 600V VD = VDRM; RL = 3.3 kΩ; TJ = 150°C MIN. IH IT = 400mA (initial) MAX. IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs tq IG = 2 x IGT; PW = 15µs; IT = 80A tgt V 650 400 600 350 550 300 500 VGD mA 1.5 400V VD = VDRM; gate open; TJ = 125°C Unit V/μs 250 0.2 V 60 50 mA MAX. 35 μs TYP. 2 μs NOTE: xx = voltage, x = package Static Characteristics Symbol Test Conditions VTM IT = 80A; tp = 380μs Value Unit 1.7 V MAX. TJ = 25°C IDRM / IRRM 10 TJ = 125°C @ VDRM / VRRM 2000 MAX. TJ = 150°C μA 4000 Thermal Resistances Symbol Parameter Value Unit Rθ(J-C) Junction to case (AC) SJxx40Ry/SJxx40Ny 0.8 °C/W Rθ(J-A) Junction to ambient Sxx40Ry 40 °C/W Note: xx = voltage, y = sensitivity & type Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: N  ormalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25°C) Ratio of IGT/I GT(TJ =25 ° C) 2.0 1.5 1.0 0.5 0.0 - 40 - 15 10 35 60 85 Junction Temperature(TJ ) -- ( ° C) SJxx40x Series Sxx40x Series 110 135 160 1.5 1.0 0.5 0.0 - 40 - 15 10 35 60 85 110 135 160 Junction Temperature (TJ ) --(°C) ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17 Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: O  n-State Current vs. On-State Voltage (Typical) 120 2.0 1.5 Instantaneous On-state Current (iT) – Amps Ratio of IH / IH (TJ = 25°C) TJ = 25°C 100 1.0 0.5 80 60 40 20 0.0 0 - 40 - 15 10 35 60 85 110 135 160 0.7 0.8 Junction Temperature (TJ ) -- (°C) Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Maximum Allowable Case Temperature(TC ) - ° C Average On-State Power Dissipation [PD(AV)] - (Watts) 35 30 25 20 15 10 5 0 5 10 15 20 25 30 35 1.2 1.3 1.4 1.5 1.6 140 130 120 110 100 90 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 80 70 0 40 10 20 30 40 50 RMS On - State Current[I T(RMS) ] - Amps Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Figure 8: Maximum Allowable Ambient Temperature vs. RMS On-State Current 140 Maximum Allowable Ambient Temperature (TA) - °C 150 Maximum Allowable Case Temperature(TC)-°C 1.1 150 RMS On-State Current [IT(RMS)] - (Amps) 140 130 120 110 100 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 90 80 1.0 Figure 6: M  aximum Allowable Case Temperature vs. RMS On-State Current 40 0 0.9 Instantaneous On-state Voltage (vT) – Volts 0 5 10 15 20 Average On-State Current[IT(AVG)]-Amps 25 120 100 80 60 40 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 20 0 0 0.5 1 1.5 2 2.5 RMS On-State Current [IT(RMS)] - Amps SJxx40x Series Sxx40x Series ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17 Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 Figure 9: Maximum Allowable Ambient Temperature vs. Average On-State Current Figure 10: Peak Capacitor Discharge Current 10000 Peak Discharge Current (ITM) - Amps Maximum Allowable Ambient Temperature(TA)-°C 140 120 100 80 60 40 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 20 0 1000 ITRM tW 0 0.5 1 1.5 2 100 0.5 1.0 10.0 50.0 Pulse Current Duration (tw) - ms Average On-State [IT(AVG)]-Amps Figure 11: Peak Capacitor Discharge Current Derating 1.2 Normalized Peak Current 1.0 0.8 0.6 0.4 0.2 0.0 0 25 50 75 100 125 150 Case Temperature (TC) - °C Figure 12: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. G  ate control may be lost during and immediately following surge current interval. 2. O  verload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 10 100 1000 Surge Current Duration -- Full Cycles SJxx40x Series Sxx40x Series ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17 Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish Ramp-up TL tL TS(max) Preheat TS(min) 100% Matte Tin-plated 25 time to peak temperature Test UL Recognized epoxy meeting flammability rating V-0 AC Blocking Lead Material Copper Alloy Temperature Cycling Careful selection of the correct component for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. SJxx40x Series Sxx40x Series Time Environmental Specifications Body Material Design Considerations Ramp-do Ramp-down tS 217°C 60 – 150 seconds - Time (tL) tP TP Temperature Reflow Condition Temperature/ Humidity High Temp Storage Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 150°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C Low-Temp Storage 1008 hours; -40°C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Moisture Sensitivity Level Level 1, JEDEC-J-STD-020D ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17 Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT AREA (REF.) 0.17 IN2 O A E Dimension 8.13 .320 P ANODE B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M J Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Min Max Min Max A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 Dimensions – TO- 263 (N-package) — D2-Pak Surface Mount TC MEASURING POINT B Dimension E ANODE 8.41 .331 7.01 .276 A S W K GATE CATHODE G H D F 11.68 .460 2.16 .085 7.01 .276 7.01 .276 16.89 .665 8.89 .350 1.40 .055 3.81 .150 Inches AREA: 0.11 in 2 C V Millimeters U D 0.025 0.035 0.63 0.89 J E 0.048 0.055 1.22 1.40 8.13 .320 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.083 0.093 2.11 2.36 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.87 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 2.03 .080 6.60 .260 SJxx40x Series Sxx40x Series ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17 Teccor® brand Thyristors 40 Amp Amp Standard Standard High SCRsTemperature SCRs 40 TO-220 AB - (R Package) TO-263 AB - (N Package) Part Numbering System Part Marking System SJ 60 40 R 2 56 DEVICE TYPE SJ: high temperature SCR SJ6040R Lead Form Dimensions xx: Lead Form Option VOLTAGE RATING 40: 400V 60: 600V YM SENSITIVITY & TYPE [blank]: 40mA 2: 15mA CURRENT RATING 40: 40A ® PACKAGE TYPE R: TO-220 (Non-isolated) N: TO-263 (D 2 - Pak) Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Product Selector Part Number Voltage Gate Sensitivity Type Package X 40mA Standard SCR TO-220R X 40mA Standard SCR TO-263 X X 15mA Standard SCR TO-220R X X 15mA Standard SCR TO-263 400V 600V SJxx40R X SJxx40N X SJxx40R2 SJxx40N2 Note: xx = Voltage Packing Options Part Number Marking Weight Packing Mode Base Quantity SJxx40RTP SJxx40R 2.2g Tube 500 (50 per tube) SJxx40NTP SJxx40N 1.6g Tube 500 (50 per tube) SJxx40NRP SJxx40N 1.6g Embossed Carrier 500 SJxx40R2TP SJxx40R2 2.2g Tube 500 (50 per tube) SJxx40N2RP SJxx40N2 1.6g Embossed Carrier 500 Note: xx = Voltage Reel Pack (RP) for TO-263 Embossed Carrier Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DIA (1.5) 0.945 (24.0) 0.827 (21.0) Cathode * * Cover tape Anode 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed SJxx40x Series Sxx40x Series ©2017 Littelfuse, Inc Specifications are subject to change without notice. Revised: 05/10/17