SK010NRP

Thyristors 10 Amp Sensitive & Standard SCRs Sxx10xSx & Sxx10x Series RoHS Description This Sxx10x SCR series is ideal for uni-directional switch applications such as phase control, heating, motor speed controls, converters/rectifiers and capacitive discharge ignitions. These SCRs have a low gate current trigger level of 0.2 to 15 mA at approximately 1.5V, with a sensitive version of this series having a gate trigger current less than 500µA. The sensitive gate SCR version is easily triggered by sense coils, proximity switches, and microprocessors. Main Features Features & Benefits Symbol Value Unit IT(RMS) 10 A VDRM / VRRM 400 to 1000 V IGT 0.2 to 15 mA Additional Information Datasheet Resources • Halogen-free and RoHS-compliant • Voltage capability up to 1000 V • Glass – passivated junctions • Surge capability up to 100 A at 60 Hz half cycle Applications Samples Typical applications includes capacitive discharge system for motorcycle engine CDI, portable generator engine ignition, strobe lights and nailers, as well as generic rectifiers, battery voltage regulators and converters. Also AC control & rectification for power tools, home/brown goods, white goods appliances and 2-wheeler rectifier/ battery regulators. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol A K G ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Absolute Maximum Ratings — Sensitive SCRs Symbol IT(RMS) IT(AV) ITSM Parameter RMS on-state current Average on-state current Peak non-repetitive surge current Test Conditions Sxx10LSy TC = 80°C Sxx10RSy /Sxx10NSy Sxx10DSy Sxx10VSy TC = 95°C Sxx10LSy TC = 80°C Sxx10RSy /Sxx10NSy Sxx10DSy Sxx10VSy TC = 95°C Value Unit 10 A 6.4 A single half cycle; f = 50Hz; TJ (initial) = 25°C 83 single half cycle; f = 60Hz; TJ (initial) = 25°C 100 A I2t I2t Value for fusing tp = 8.3 ms 41 A 2s di/dt Critical rate of rise of on-state current f = 60 Hz ; TJ = 110°C 100 A/μs IGM Peak gate current TJ = 110°C 1 A PG(AV) Average gate power dissipation TJ = 110°C 0.1 W Tstg Storage temperature range -40 to 150 °C TJ Operating junction temperature range -40 to 110 °C Value Unit 10 A 6.4 A Note: xx = voltage, y = sensitivity Absolute Maximum Ratings — Standard SCRs Symbol IT(RMS) IT(AV) ITSM Parameter RMS on-state current Average on-state current Peak non-repetitive surge current Test Conditions Sxx10L TC = 95°C Sxx10R / Sxx10N Sxx10D Sxx10V TC = 105°C Sxx10L TC = 95°C Sxx10R / Sxx10N Sxx10D Sxx10V TC = 105°C single half cycle; f = 50Hz; TJ (initial) = 25°C 83 single half cycle; f = 60Hz; TJ (initial) = 25°C 100 A I2t I2t Value for fusing tp = 8.3 ms 41 A 2s di/dt Critical rate-of-rise of on-state current f = 60 Hz TJ = 125°C 100 A/μs IGM Peak gate current TJ = 125°C 2 A PG(AV) Average gate power dissipation TJ = 125°C 0.5 W Tstg Storage temperature range -40 to 150 °C TJ Operating junction temperature range -40 to 125 °C Note: xx = voltage ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Sensitive SCRs Symbol Value Test Conditions Sxx10xS2 Sxx10xS3 Unit IGT VD = 6V RL = 100 Ω MAX. VGT VD = 6V RL = 100 Ω MAX. 0.8 V 200 500 μA dv/dt VD = VDRM; RGK = 1kΩ ; TJ = 110°C TYP. 8 V/μs VGD VD = VDRM; RL = 3.3 kΩ; TJ = 110°C MIN. 0.2 V VGRM IGR = 10μA MIN. 6 IH IT = 20mA (initial) MAX. 6 8 mA tq (1) MAX. 50 45 μs tgt IG = 2 x IGT; PW = 15µs; IT = 12A TYP. 4 5 μs V Note: xx = voltage, x = package (1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Standard SCRs Symbol Value Test Conditions Sxx10x Unit IGT VD = 12V RL = 60 Ω - MAX. 15 mA VGT VD = 12V RL = 60 Ω - MAX. 1.5 V VD = VDRM; gate open; TJ = 100°C 400V 350 600V 300 800V dv/dt 1000V 250 MIN. 400V VD = VDRM; gate open; TJ = 125°C VGD 100 V/μs 250 600V 225 800V 200 VD = VDRM; RL = 3.3 kΩ; TJ = 125°C - MIN. 0.2 V IH IT = 200mA (initial) - MAX. 30 mA tq (1) - MAX. 35 μs tgt IG = 2 x IGT; PW = 15µs; IT = 20A - TYP. 2 μs Note: xx = voltage, x = package (1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs Static Characteristics Symbol Test Conditions VTM IT = 20A; tp = 380 µs Sxx10xyy IDRM / IRRM Sxx10x Value Unit 1.6 V TJ = 25°C 400 - 600V 5 TJ = 110°C 400 - 600V 250 TJ = 25°C VDRM / VRRM MAX. TJ = 100°C TJ = 125°C 400 - 800V 1000V 10 MAX. 20 400 - 800V 200 1000V 3000 400 - 800V 500 μA Note: xx = voltage, x = package, yy = sensitivity ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Thermal Resistances Symbol Parameter Value Junction to case (AC) Rθ(J-C) Junction to ambient Rθ(J-A) Sxx10RSy / Sxx10NSy 1.6 Sxx10LSy 3.0 Sxx10VSy 1.7 Sxx10DSy 1.45 Sxx10R / Sxx10N 1.6 Sxx10L 3.0 Sxx10V 1.7 Sxx10D 1.45 Sxx10RSy 40 Sxx10LSy 65 Sxx10VSy 85 Sxx10R 40 Sxx10L 50 Sxx10V 70 Unit °C/W °C/W Note: xx = voltage, y = sensitivity Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature (Sensitive SCR) Figure 2: N  ormalized DC Gate Trigger Current vs. Junction Temperature (Standard SCR) 4.0 Ratio of IGT / IGT (TJ = 25°C) Ratio of IGT / IGT (TJ = 25°C) 4.0 3.0 2.0 1.0 0.0 -40 -15 10 35 60 85 3.0 2.0 1.0 0.0 110 -40 -15 Junction Temperature (TJ) -- (°C) Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature 60 85 110 125 2.0 Ratio of IH / IH (TJ = 25°C) Ratio of VGT / VGT (TJ = 25°C) 35 Figure 4: N  ormalized DC Holding Current vs. Junction Temperature 2.0 1.5 1.0 0.5 0.0 10 Junction Temperature (TJ) -- (°C) 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 Junction Temperature (TJ) -- (°C) 110 125 -40 -15 10 35 60 85 110 125 Junction Temperature (TJ) -- (°C) ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Figure 5: On-State Current vs. On-State Voltage (Typical) Figure 6: P  ower Dissipation (Typical) vs. RMS On-State Current 10 32 Average On-State Power Dissipation [PD(AV)] -- (Watts) Instantaneous On-state Current (iT) – Amps TJ = 25ºC 28 24 20 16 12 8 4 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 9 8 7 6 5 4 3 2 1 0 1.6 0 1 2 Instantaneous On-state Voltage (vT) – Volts Figure 7: Maximum Allowable Case Temperature vs. RMS On-State Current 130 125 125 Maximum Allowable Case Temperature (TC) - °C Maximum Allowable Case Temperature (TC) - °C 110 105 Sxx10RSy/ Sxx10RSy Sxx10NSy 100 Sxx10DSy Sxx10VSy 95 90 Sxx10LSy 85 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 80 75 7 8 9 10 Sxx10R/ Sxx10R Sxx10N Sxx10L Sxx10D Sxx10V 5 6 110 105 100 Sxx10RSy/ Sxx10RSy Sxx10NSy Sxx10DSy Sxx10VSy 95 90 Sxx10LSy 85 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 75 70 0 1 2 3 4 5 6 7 8 9 10 11 0 1 RMS On-State Current [IT(RMS)] - Amps 2 3 4 7 Average On-State Current [IT(AVE)] - Amps Figure 9: Maximum Allowable Ambient Temperature vs. RMS On-State Current Figure 10: Maximum Allowable Ambient Temperature vs. Average On-State Current 120 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Sxx10R 100 Maximum Allowable Ambient Temperature (TA) - °C Maximum Allowable Case Temperature (TC) - °C 6 115 80 70 Sxx10L 80 60 5 120 Sxx10R Sxx10D Sxx10V Sxx10L 115 4 Figure 8: M  aximum Allowable Case Temperature vs. Average On-State Current 130 120 3 RMS On-State Current [IT(RMS)] -- (Amps) Sxx10V Sxx10RSy Sxx10LSy 40 Sxx10VSy 20 Sxx10R 100 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING Sxx10L 80 Sxx10RSy Sxx10LSy 60 Sxx10V 40 Sxx10VSy 20 0 0 0.0 0.5 1.0 1.5 2.0 Average On-State Current [IT(RMS)] - Amps Note: xx = voltage, y = sensitivity 2.5 0.0 0.5 1.0 1.5 Average On-State Current [IT(AVE)] - Amps ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Figure 11: Peak Capacitor Discharge Current Figure 12: P  eak Capacitor Discharge Current Derating 1.2 1.0 Normalized Peak Current Peak Discharge Current (ITM) - Amps 1000 100 ITRM 0.8 0.6 0.4 Sensitive SCR Standard SCR 0.2 tW 10 0.5 1.0 0.0 10.0 50.0 Pulse Current Duration (tW) - ms 0 25 50 75 100 125 150 Case Temperature (TC) - °C Figure 13-1: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS2 Figure 13-1: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS3 Figure 14-1: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS2 Figure 14-2: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS3 ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Figure 15-1: Typical Static dv/dt with RGK vs. Junction Temperature for S60010xS2 Figure 15-2: Typical Static dv/dt with RGK vs. Junction Temperature for S60010xS3 Figure 16-1: Typical turn off time with RGK vs. Junction Temperature for S60010xS2 Figure 16-2: Typical DC Gate Trigger Current with RGK vs. Junction Temperature for S60010xS3 Figure 17: S  urge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature 100 Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 10 1 1 10 100 1000 Surge Current Duration -- Full Cycles ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C +0/-5 tP TP °C Physical Specifications Terminal Finish 100% Matte Tin-plated Body Material UL Recognized epoxy meeting flammability rating 94V-0 Lead Material Copper Alloy Design Considerations Careful selection of the correct component for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 Ramp-do Ramp-down tS time to peak temperature Time Environmental Specifications Test Specifications and Conditions AC Blocking MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours Temperature Cycling MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time Temperature/Humidity EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity High Temp Storage MIL-STD-750, M-1031, 1008 hours; 150°C Low-Temp Storage 1008 hours; -40°C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Product Selector Voltage Part Number Gate Sensitivity Type Package - 0.2mA Sensitive SCR TO-220R - 0.2mA Sensitive SCR TO-220L - - 0.2mA Sensitive SCR TO-251 X - - 0.2mA Sensitive SCR TO-252 X X - - 0.5mA Sensitive SCR TO-220R 400V 600V 800V 1000V Sxx10RS2 X X - Sxx10LS2 X X - Sxx10VS2 X X Sxx10DS2 X Sxx10RS3 Sxx10LS3 X X - - 0.5mA Sensitive SCR TO-220L Sxx10VS3 X X - - 0.5mA Sensitive SCR TO-251 Sxx10DS3 X X - - 0.5mA Sensitive SCR TO-252 Sxx10R X X X X 15mA Standard SCR TO-220R TO-220L Sxx10L X X X X 15mA Standard SCR Sxx10V X X X X 15mA Standard SCR TO-251 Sxx10D X X X X 15mA Standard SCR TO-252 Sxx10NS2 X X - - 15mA Sensitive SCR TO-263 Sxx10NS3 X X - - 15mA Sensitive SCR TO-263 Sxx10N X X X X 15mA Standard SCR TO-263 Note: xx = Voltage/10 Dimensions — TO-251AA (V/I-Package) — V/I-PAK Through Hole TC MEASURING POINT Anode E H D AREA: 0.040 IN2 Dimension 5.28 .208 J A 5.34 .210 B R P Q S K C Cathode Anode GATE F G L Inches Millimeters Min Typ Max Min Typ A 0.037 0.040 0.043 0.94 1.01 Max 1.09 B 0.235 0.242 0.245 5.97 6.15 6.22 C 0.350 0.361 0.375 8.89 9.18 9.53 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.66 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.34 2.41 I 0.176 0.180 0.184 4.47 4.57 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.52 0.58 P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 R 0.034 0.039 0.044 0.86 1.00 1.11 S 0.074 0.079 0.084 1.86 2.00 2.11 I ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount Anode E D 6.71 .264 5.28 .208 TC MEASURING POINT Dimension A 6.71 .264 5.34 .210 B 1.60 .063 P Q C 1.80 .071 GATE F Cathode Anode AREA : 0.040 IN2 3 .118 G 4.60 .181 I O L K J H M N Inches Millimeters Min Typ Max Min Typ A 0.037 0.040 0.043 0.94 1.01 Max 1.09 B 0.235 0.243 0.245 5.97 6.16 6.22 C 0.106 0.108 0.113 2.69 2.74 2.87 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.65 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.33 2.41 I 0.176 0.179 0.184 4.47 4.55 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.51 0.58 M 0.000 0.000 0.004 0.00 0.00 0.10 N 0.021 0.026 0.027 0.53 0.67 0.69 O 0° 0° 5° 0° 0° 5° P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 Dimensions — TO-263 (N-Package) — D2PAK Surface Mount Dimension Inches Millimeters Min Max Min A 0.360 0.370 9.14 Max 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 D 0.025 0.035 0.64 0.89 E 0.045 0.060 1.14 1.52 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.092 0.102 2.34 2.59 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.88 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT AREA (REF.) 0.17 IN2 Dimension O A E 8.13 .320 P A ANODE B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M J Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 2.92 B 0.105 0.115 2.67 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Min Max Min Max 0.380 0.420 9.65 10.67 2.92 Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab TC MEASURING POINT O A E P AREA (REF.) 0.17 IN2 8.13 .320 A B C 13.36 .526 D 7.01 .276 F R G L H CATHODE ANODE GATE K J N M Dimension Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters B 0.105 0.115 2.67 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20 Thyristors 10 Amp Sensitive & Standard SCRs Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx10L/RyyTP Sxx10L/Ryy 2.2 g Tube 1000 (50 per tube) 750 (75 per tube) Sxx10DyyTP Sxx10Dyy 0.3 g Tube Sxx10DyyRP Sxx10Dyy 0.3 g Embossed Carrier 2500 Sxx10VyyTP Sxx10Vyy 0.4 g Tube 750 (75 per tube) Sxx10L/RTP Sxx10L/R 2.2 g Tube 1000 (50 per tube) Sxx10DTP Sxx10D 0.3 g Tube 750 (75 per tube) Sxx10DRP Sxx10D 0.3 g Embossed Carrier 2500 Sxx10VTP Sxx10V 0.4 g Tube 750 (75 per tube) 1000 (50 per tube) Sxx10NSyTP Sxx10NSy 1.6 g Tube Sxx10NSyRP Sxx10NSy 1.6 g Embossed Carrie 500 Sxx10NTP Sxx10N 1.6 g Tube 1000 (50 per tube) Sxx10NRP Sxx10N 1.6 g Embossed Carrier 500 Note: xx = Voltage/10; yy = Sensitivity TO-252 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards * Cover tape 0.512 (13.0) Arbor Hole Dia. 0.315 (8.0) 0.059 Dia (1.5) XXXXXX Cathode DC XX DC XX XXXXXX * DC 0.524 (13.3) XX 0.63 (16.0) XXXXXX Gate XXXXXX 0.157 (4.0) Anode 12.99 (330.0) Dimensions are in inches (and millimeters). 0.64 (16.3) Direction of Feed Part Numbering System Part Marking System S 60 10 L S2 56 COMPONENT TYPE S : SCR LEAD FORM DIMENSIONS xx : Lead Form Optio n Sxx10DS3 VOLTAGE RATING 40 : 400V 60 : 600V 80 : 800V K0 : 1000V CURRENT 10: 10A SENSITIVITY & TYPE Sensitive SCR: S2: 200µA S3: 500µA Standard SCR: (blank): 15mA PACKAGE TYPE L : TO-220 Isolated R : TO-220 Non-Isolated V : TO-251 (VPAK) D : TO-252 (DPAK) N: TO-263 (D2PAK) TO-263 AA - (N Package) TO-220 AB - (L and R Package) TO-251AA - (V Package) TO-252AA - (D Package) Sxx10DS3 Sxx10R YMXXX ® YMLDD ® YMLDD ® Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ©2019 Littelfuse, Inc Specifications are subject to change without notice. Revised: BO.12/10/20