SL1411A600A

Gas Discharge Tubes SL1011A and SL1411A Series SL1011A and SL1411A Series RoHS Description The SL1011A and SL1411A series provides high levels of protection against fast rising transients in the 100V/µs to 1kV/µs range usually caused by lightning disturbances. The SL1011A and SL1411A series offers low capacitance (< 1.5pf) which provides low insertion loss at high frequencies. SL1011A offers 5kA protection without destruction whereas the SL1411A offer 10kA surge protection without destruction (maximum single surge of 12kA @ 8/20µs). Agency Approvals Features Agency • Lead-free and RoHS compliant Agency File Number E128662 • Low insertion loss • Excellent response to fast rising transients • 5kA (SL1011A) or 10kA (SL1411A) surge capability tested with 8/20μs pulse as defined by IEC 610004-5 2nd Edition • Ultra low capacitance Applications 2 Electrode GDT Graphical Symbol • Broadband equipment • ADSL equipment • XDSL equipment • Satellite and CATV equipment • General telecom equipment Additional Information Datasheet SL1011A Resources SL1011A Samples SL1011A SL1011A Datasheet SL1411A Resources SL1411A Samples SL1411A SL1411A © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 12/20/20 Gas Discharge Tubes SL1011A and SL1411A Series Electrical Characteristics Device Specifications (at 25°C) Life Ratings Arc Nominal AC Nominal Impulse AC Impulse Voltage Surge DC Breakdown Dischage DC Max Impulse CapaciImpulse Breakdown Discharge Breakdown Insulation (on state Life Part Number in Volts1,2 Current Holdover Discharge Current tance Discharge 3 in Volts Current In Volts Resistance Voltage) (@100A (@100V/s) (9 Cycles Voltage4 (1 Application) (@1MHz) Current (10x1s (@100V/µs) (@1kV/µs) @1Amp 10/1000µs) @ 50Hz) (8/20µs) @50-60Hz) Min MIN TYP MAX MAX MIN MAX TYP TYP @ 8/20µs @ 10/350µs SL1011A075 60 75 90 500 700 72 90 108 500 600 SL1011A145 116 145 174 500 650 120 150 180 500 650 184 230 276 550 700 SL1411A075 SL1011A090 SL1411A090 SL1011A150 SL1411A1505 SL1011A230 SL1411A230 SL1011A250 200 250 300 600 800 SL1011A260 210 260 310 600 800 280 350 420 800 900 376 470 564 1000 1100 SL1011A500 400 500 600 1100 1200 720 1200 1400 SL1411A250 SL1011A350 SL1411A350 SL1011A470 SL1411A470 SL1011A600 SL1411A6005 480 600 1010 Ω (at 50V) 50 V 1.5 pF 10 Ω (at 100V) 10 ~20 V 300 shots SL1011A: 10 shots (@5kA) SL1411A: 10 shots (@10kA) SL1011A: 5A SL1011A: 20 A SL1411A: 10 A SL1411A: 65 A SL1411A: 12 kA 1 kA 135 V Notes: 1. At delivery AQL 0.65 level II, DIN ISO 2859 2. In ionized mode 3. Comparable to the silicon measurement Switching Voltage (Vs) 4. Tested according to ITU-T Rec. K.12 < 150 msecs. 5. Not UL Recognized Product Characteristics Materials Product Marking Leaded Device: Nickel-plated with Tin-plated wires Core and Surface Mount: Dull Tin-plated Glow to Arc Transition Current < 0.5 Amps Glow Voltage ~60 Volts Littelfuse 'LF' Mark, voltage and date code Storage and Operational Temperature -40 to +90°C © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 12/20/20 Gas Discharge Tubes SL1011A and SL1411A Series Device Dimensions For SL1011A Series: 'A' Type Axial Lead Devices 'C' Type Core Devices PROFILE VIEW TOP VIEW TOP VIEW PROFILE VIEW Ø8.0 ± 0.2 [0.315 ± 0.0079] Ø0.8 [0.031] 6.05 ± 0.2 [0.238 ± 0.0079] Ø8.0 ± 0.2 Ø8.0 ± 0.2 [0.315 ± 0.0079] SEMI–PROFILE VIEW 6.05 ± 0.2 [0.238 ± 0.0079] 62 ± 2 For SL1411A series: 'A' Type Axial Lead Devices 'SM' Type Surface Mount Devices PROFILE VIEW TOP VIEW TOP VIEW PROFILE VIEW 8.3 ± 0.1 4 [0.157] Ø1.0 [0.039] + 0.10 Ø8.0 – 0.30 0.0039 [0.315 + – 0.0118 ] 5.55 [0.219] Ø8.3 ± 0.15 6.05 ± 0.2 [0.238 ± 0.0079] 6.05 ± 0.2 [0.238 ± 0.0079] 9. Ø 62 ± 2 SEMI–PROFILE VIEW 30 0.5 ± 0.1 ± 2 0. SOLDER PAD LAYOUT 1.30 [0.051] 'C' Type Core Devices 7.00 [0.276] TOP VIEW PROFILE VIEW + 0.10 Ø8.00 – 0.30 0.0039 [0.315 + – 0.0118 ] SEMI–PROFILE VIEW 5.40 [0.213] + 0.10 Ø8.00 – 0.30 + 0.20 6.05 – 0.15 0.0079 [0.238 + – 0.0059 ] © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 12/20/20 Gas Discharge Tubes SL1011A and SL1411A Series Soldering Parameters - Reflow Soldering (Surface Mount Devices) Pb-free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (Min to Max) (ts) 60 – 180 seconds Average Ramp-up Rate (Liquidus Temp (TL) 5°C/second max. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of Actual Peak Temperature (tp) 10 – 30 seconds +0/-5 °C 6°C/second max. Time 25°C to Peak Temperature (TP) 8 minutes max. Do not exceed 260°C tL Ramp-down Preheat TS(min) 25 Ramp-down Rate Critical Zone TL to TP Ramp-up TL TS(max) 3°C/second max. to peak) tP TP Temperature Reflow Condition tS time to peak temperature (t 25ºC to peak) Time Soldering Parameters - Wave Soldering (Thru-Hole Devices) Recommended Process Parameters: 280 Wave Parameter 260 240 Lead-Free Recommendation Preheat: 220 (Depends on Flux Activation Temperature) 200 180 160 140 120 100 (Typical Industry Recommendation) Temperature Minimum: 100° C Temperature Maximum: 150° C Preheat Time: 60-180 seconds Solder Pot Temperature: 280° C Maximum Solder Dwell Time: 2-5 seconds 80 60 40 230 240 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 20 0 0 30 20 10 Temperature (°C) - Measured on bottom side of board 300 Time (Seconds) Cooling Time Preheat Time Dwell Time Soldering Parameters - Hand Soldering Solder Iron Temperature: 350° C +/- 5°C Heating Time: 5 seconds max. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 12/20/20 < 0.7 Max. Gas Discharge Tubes 52.5 ± 1.5 [2.066 ± 0.059] SL1011A and SL1411A Series 22.8 [0.898] 6±1 [0.236 ± 0.039] 10 ± 0.5 Pitch [0.394 ± 0.020] Packaging Dimensions For Axial Lead Items Dimensions are in millimeters [and inches] Dimensions are in millimeters [and inches] < 1.2 Max. Lead Bend 254.0 - 356.0 [10.0 - 14.0] For SL1011A series: < 0.7 Max. SL1011A XXX X Direction of Feed 77.0 Max. [3.03] 52.5 ± 1.5 Voltage [2.066 ± 0.059] 22.8 [0.898] Pin Configuration A = Axial Lead C = Core 6±1 [0.236 ± 0.039] 10 ± 0.5 Pitch [0.394 ± 0.020] Remarks: Formed leads are available on request For 'SM' Type Surface Mount Items (SL1411A series only) Dimensions are in millimeters [and inches] 10x4 ± 0.1 = 40 ± 0.2 [10x0.157 ± 0.004 = 1.575 ± 0.008] 0.4 ± 0.05 [0.016 ± 0.002] 1.75 ± 0.1 [0.069 ± 0.004] 254.0 - 356.0 [10.0 - 14.0] For SL1011B series: 275.0 [10.83] 100.0 [3.94] SL1011B 76.0 4 ± 0.1 [0.157 ± 0.004] 1.5 DIA. MAX. [0.059] [2.99] 7.5 ± 0.1 [0.295 ± 0.004] 8.5 ± 0.1 [0.335 ± 0.004] XXX X 25.0 [0.98] Voltage 16 +0.3 / -0.1 [0.630 +0.012 / -0.004] 77.0 Max. [3.03] 8.6 ± 0.1 [0.339 ± 0.004] Dimensions are in millimeters [and inches] 17.7 [0.697] 1.5 DIA. MAX. [0.059] Pin Configuration Direction of Feed 12 ± 0.1 [0.472 ± 0.004] For 'C' Type Core Items: Packed in plastic bag (500 pcs) Part Numbering System and Ordering Information Direction of Feed A = Axial Lead C = Core Remarks: Formed leads are available on request For SL1411A series: For SL1011A series: SL1411 A XXX XX SL1011A XXX X Surge Capability Voltage Voltage Pin Configuration Pin Configuration A = Axial Lead C = Core Remarks: Formed leads are available on request A = Axial Lead C = Core SM = Surface Mount For SL1011B series: SL1011B XXX X Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 12/20/20 Voltage