SMA6J6.0CA

TVS Diodes Surface Mount – 600W > SMA6J series SMA6J Series RoHS Pb e3 Description The SMA6J series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Features Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 600 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 3.3 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 60 A Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only VF 3.5 V Peak Pulse Power Dissipation by 10/1000μs Waveform (Fig.2) (Note 1), (Note 2) TJ -65 to 150 °C Storage Temperature Range TSTG -65 to 175 °C Typical Thermal Resistance Junction to Lead RθJL 30 °C/W Typical Thermal Resistance Junction to Ambient RθJA 120 °C/W Operating Temperature Range • Small DO-214AC SMT footprint for minimal board space requirement • Typical failure mode is a short circuit condition for current events exceeding component rating • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • Built-in strain relief • Glass passivated junction • Low inductance • Excellent clamping capability • 600W peak pulsepower capability at 10/1000μs waveform, repetition rate (duty cycle): 0.01% •F  ast response time: typically less than 1.0ps from 0 Volts to VBR min • Typical IR < 1µA when VBR min > 12 V • High temperature reflow soldering guaranteed: 260°C/30sec • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • UL Recognized compound meeting flammability rating V-0 • Meet MSL level1, per J-STD-020, lead-frame maximun peak of 260°C • Matte tin lead–free plated • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) Notes: 1. Non-repetitive current pulse, per Fig.4 and derated above TJ (initial) =25ºC per Fig. 3. 2. Mounted on 5.0x5.0mm copper pad to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only. Functional Diagram Applications TVS components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.01/05/21 TVS Diodes Surface Mount – 600W > SMA6J series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) SMA6J5.0A SMA6J6.0A SMA6J6.5A SMA6J7.0A SMA6J7.5A SMA6J8.0A SMA6J8.5A SMA6J9.0A SMA6J10A SMA6J11A SMA6J12A SMA6J13A SMA6J14A SMA6J15A SMA6J16A SMA6J17A SMA6J18A SMA6J20A SMA6J22A SMA6J24A SMA6J26A SMA6J28A SMA6J30A SMA6J33A SMA6J36A SMA6J40A SMA6J43A SMA6J45A SMA6J48A SMA6J51A SMA6J54A SMA6J58A SMA6J60A SMA6J64A SMA6J70A SMA6J75A SMA6J78A SMA6J85A SMA6J90A SMA6J100A SMA6J110A SMA6J120A SMA6J130A Part Number (Bi) SMA6J5.0CA SMA6J6.0CA SMA6J6.5CA SMA6J7.0CA SMA6J7.5CA SMA6J8.0CA SMA6J8.5CA SMA6J9.0CA SMA6J10CA SMA6J11CA SMA6J12CA SMA6J13CA SMA6J14CA SMA6J15CA SMA6J16CA SMA6J17CA SMA6J18CA SMA6J20CA SMA6J22CA SMA6J24CA SMA6J26CA SMA6J28CA SMA6J30CA SMA6J33CA SMA6J36CA SMA6J40CA SMA6J43CA SMA6J45CA SMA6J48CA SMA6J51CA SMA6J54CA SMA6J58CA SMA6J60CA SMA6J64CA SMA6J70CA SMA6J75CA SMA6J78CA SMA6J85CA SMA6J90CA - Marking UNI 6BA 6AG 6AK 6AM 6AP 6AR 6AT 6AV 6AX 6AZ 6BE 6BG 6BK 6BM 6BP 6BR 6BT 6BV 6BX 6BZ 6CE 6CG 6CK 6CM 6CP 6CR 6CT 6CV 6CX 6CZ 6RE 6RG 6RK 6RM 6RP 6RR 6RT 6RV 6RX 6RZ 6SE 6SG 6SK BI 6WE 6WG 6WK 6WM 6WP 6WR 6WT 6WV 6WX 6WZ 6XE 6XG 6XK 6XM 6XP 6XR 6XT 6XV 6XX 6XZ 6YE 6YG 6YK 6YM 6YP 6YR 6YT 6YV 6YX 6YZ 6ZE 6ZG 6ZK 6ZM 6ZP 6ZR 6ZT 6ZV 6ZX - Reverse Stand off Voltage VR (Volts) 5 6 6.5 7 7.5 8 8.5 9 10 11 12 13 14 15 16 17 18 20 22 24 26 28 30 33 36 40 43 45 48 51 54 58 60 64 70 75 78 85 90 100 110 120 130 Breakdown Voltage VBR (Volts) @ IT MIN 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.0 11.1 12.2 13.3 14.4 15.6 16.7 17.8 18.9 20.0 22.2 24.4 26.7 28.9 31.1 33.3 36.7 40.0 44.4 47.8 50.0 53.3 56.7 60.0 64.4 66.7 71.1 77.8 83.3 86.7 94.4 100 111 122 133 144 MAX 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.1 12.3 13.5 14.7 15.9 17.2 18.5 19.7 20.9 22.1 24.5 26.9 29.5 31.9 34.4 36.8 40.6 44.2 49.1 52.8 55.3 58.9 62.7 66.3 71.2 73.7 78.6 86.0 92.1 95.8 104 111 123 135 147 159 Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) Agency Recognition (mA) Maximum Clamping Voltage VC @ Ipp (V) 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103 113 121 126 137 146 162 177 193 209 66.0 61.0 56.0 50.0 46.5 44.1 41.7 39.0 37.0 33.0 31.0 29.0 25.8 25.1 23.1 22.6 21.5 19.4 17.0 16.0 14.9 13.8 12.5 11.8 10.4 9.7 8.7 8.3 8.1 7.4 6.9 6.7 6.2 5.9 5.5 5.0 4.8 4.6 4.2 3.8 3.5 3.2 2.9 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Test Current IT For bidirectional type having VR of 10 volts and less, the IR limit is double. © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.01/05/21 TVS Diodes Surface Mount – 600W > SMA6J series I-V Curve Characteristics Uni-directional I I Bi-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified IPPM (peak impulse current @ 10/1000) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 Time 0.001 0.01 0.1 1 td-Pulse Width (ms.) © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.01/05/21 TVS Diodes Surface Mount – 600W > SMA6J series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 6 - Peak Forward Voltage Drop vs Peak Forward Current (typical values) 100 I F - Peak Forward Current(A) 1000 Transient Thermal Impedance ( °C/W) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 0 175 Figure 5 - Typical Transient Thermal Impedance 100 10 1 0.1 0.001 0.01 0.1 1 10 100 1000 10 1 0.1 0.01 TP - Pulse Duration (s) 0 1 2 3 4 5 6 VF - Peak Forward Voltage(V) Figure 7 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only 80 Figure 8 - Typical Junction Capacitance 10000 Uni-directional V=0V 70 1000 60 Cj(pF) IFSM - Peak Forward Surve Current(A) tr=10µsec 50 40 Bi-directional V=0V Uni-directional V=VR 100 Bi-directional V=VR 30 20 10 10 0 1 10 Number of Cycles at 60 Hz 100 1 1 10 100 1000 VBR - Reverse Breakdown Voltage(V) © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.01/05/21 TVS Diodes Surface Mount – 600W > SMA6J series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow 217°C - Temperature (TL) (Liquidus) 60 – 150 seconds - Time (min to max) (tL) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 30 seconds max Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C 0.002 ounce, 0.061 gram JEDEC DO-214AC Molded Plastic over glass passivated junction Color band denotes cathode except Bipolar Matte Tin-plated leads, Solderable per JESD22-B102 Case Polarity Terminal Ramp-up TL Critical Zone TL to TP tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications Physical Specifications Weight tp TP Temperature (T) Reflow Condition High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 Dimensions DO-214AC (SMA) Dimensions Cathode Band C B H D F E G J K Millimeters Max Min Max 0.049 0.065 1.250 1.650 B 0.157 0.181 3.990 4.600 C 0.095 0.110 2.400 2.790 D 0.075 0.090 1.900 2.290 E 0.030 0.060 0.780 1.520 F - 0.008 - 0.203 G 0.189 0.208 4.800 5.280 H 0.006 0.012 0.152 0.305 I 0.070 - 1.800 - J 0.082 - 2.100 - K - 0.090 - 2.300 L 0.082 - 2.100 - A A Inches Min L I Solder Pads (all dimensions in mm) © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.01/05/21 TVS Diodes Surface Mount – 600W > SMA6J series Part Numbering System Part Marking System xx C A SMA6J Cathode Band F 5% Vbr Voltage Tolerance Bi-directional XX YMXXX Vr Voltage Series Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Part number Component Package Quantity Packaging Option Packaging Specification SMA6JxxXX DO-214AC 5000 Tape & Reel - 12mm tape/13” reel EIA RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.01/05/21