SMBJ100CA-HRA

TVS Diode Surface Mount – 600W > SMBJ-HRA Series SMBJ-HRA Series RoHS Pb e3 Description The SMBJ-HRA High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 600 W Power Dissipation on Infinite Heat Sink at TA=50OC PM(AV) 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only VF 3.5V V Operating Junction and Storage Temperature Range TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead RƟJL 20 °C/W Typical Thermal Resistance Junction to Ambient RƟJA 100 °C/W Notes: 1. Non-repetitive current pulse per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Features • 600W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 1µA above 12V • For surface mounted applications to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC 61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • Fast response time: typically less than 1.0ps from 0V to BV min • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • Glass passivated chip junction • High temperature soldering guaranteed: 260°C/40 seconds at terminals • Plastic package is flammability rated V-0 per UL 94 • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C. • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) • UL Recognized to ANSI/ UL 497B, “Protectors for Data Communications and Fire-Alarm Circuits.” Applications TVS Components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/14/20 TVS Diode Surface Mount – 600W > SMBJ-HRA Series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) SMBJ5.0A-HRA SMBJ6.0A-HRA SMBJ6.5A-HRA SMBJ7.0A-HRA SMBJ7.5A-HRA SMBJ8.0A-HRA SMBJ8.5A-HRA SMBJ9.0A-HRA SMBJ10A-HRA SMBJ11A-HRA SMBJ12A-HRA SMBJ13A-HRA SMBJ14A-HRA SMBJ15A-HRA SMBJ16A-HRA SMBJ17A-HRA SMBJ18A-HRA SMBJ20A-HRA SMBJ22A-HRA SMBJ24A-HRA SMBJ26A-HRA SMBJ28A-HRA SMBJ30A-HRA SMBJ33A-HRA SMBJ36A-HRA SMBJ40A-HRA SMBJ43A-HRA SMBJ45A-HRA SMBJ48A-HRA SMBJ51A-HRA SMBJ54A-HRA SMBJ58A-HRA SMBJ60A-HRA SMBJ64A-HRA SMBJ70A-HRA SMBJ75A-HRA SMBJ78A-HRA SMBJ85A-HRA - SMBJ5.0CA-HRA SMBJ6.0CA-HRA SMBJ6.5CA-HRA SMBJ7.0CA-HRA SMBJ7.5CA-HRA SMBJ8.0CA-HRA SMBJ8.5CA-HRA SMBJ9.0CA-HRA SMBJ10CA-HRA SMBJ11CA-HRA SMBJ12CA-HRA SMBJ13CA-HRA SMBJ14CA-HRA SMBJ15CA-HRA SMBJ16CA-HRA SMBJ17CA-HRA SMBJ18CA-HRA SMBJ20CA-HRA SMBJ22CA-HRA SMBJ24CA-HRA SMBJ26CA-HRA SMBJ28CA-HRA SMBJ30CA-HRA SMBJ33CA-HRA SMBJ36CA-HRA SMBJ40CA-HRA SMBJ43CA-HRA SMBJ45CA-HRA SMBJ48CA-HRA SMBJ51CA-HRA SMBJ54CA-HRA SMBJ58CA-HRA SMBJ60CA-HRA SMBJ64CA-HRA SMBJ70CA-HRA SMBJ75CA-HRA SMBJ78CA-HRA SMBJ85CA-HRA SMBJ90CA-HRA SMBJ100CA-HRA SMBJ110CA-HRA SMBJ120CA-HRA SMBJ130CA-HRA SMBJ150CA-HRA SMBJ160CA-HRA SMBJ170CA-HRA Marking UNI BI KEH KGH KKH KMH KPH KRH KTH KVH KXH KZH LEH LGH LKH LMH LPH LRH LTH LVH LXH LZH MEH MGH MK H MMH MPH MRH MTH MVH MXH MZH NEH NGH NKH NMH NPH NRH NTH NVH - AEH AGH AKH AMH APH ARH ATH AVH AXH AZH BEH BGH BKH BMH BPH BRH BTH BVH BXH BZH CEH CGH CKH CMH CPH CRH CTH CVH CXH CZH DEH DGH DKH DMH DPH DRH DTH DVH DXH DZH EEH EGH EKH EMH EPH ERH Reverse Stand off Voltage VR (Volts) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 Breakdown Voltage VBR (Volts) @ IT Test Current IT MIN MAX (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Maximum Maximum Clamping Reverse Peak Voltage VC Leakage IR Pulse Current @ Ipp @ VR Ipp (A) (µA) (V) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.2 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/14/20 TVS Diode Surface Mount – 600W > SMBJ-HRA Series Screen Process 100% Vision Inspection MIL-STD-750 method 2074 100% High Temperature Storage Life (168hrs,175°C) MIL-STD-750 method 1031 100% X-RAY inspection MIL-STD-750 method 2076 100% Temperature Cycle Test (-55 to150°C, 20 cycles, dwell time 15 min) MIL-STD-750 method 1051 100% Reflow (2x) JEDEC J-STD-020 100% Surge Test (2x) MIL-STD-750 method 4066 100% HTRB 150°C Bias=VR(80% breakdown voltage, 96hrs, and each direction 96hrs for Bi-directional products) MIL-STD–750 method 1038 Final Electrical Test( 100% 3 sigma limit, 100% dynamic test and PAT limit) MIL-STD-750 method 4016.4021.4011 Note: Up-screen program can be specified by customer’s request via contacting Littelfuse service I-V Curve Characteristics Uni-directional Bi-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 Time 0.001 0.01 0.1 1 td-Pulse Width (ms.) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/14/20 TVS Diode Surface Mount – 600W > SMBJ-HRA Series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) tr=10µsec ( ) 2 50 0 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 Figure 6 - Steady State Power Dissipation Derating Curve 100000 Uni-di PM(AV), Steady State Power Dissipation (W) 6 10000 onal V=0V Bi-direc Cj (pF) Half Value IPPM IPPM t-Time (ms) Figure 5 - Typical Junction Capacitance nal V=0V 1000 100 Uni-di onal Bi-direc nal V=VR 10 1 Peak Value IPPM 100 175 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 1 10 1 00 1000 VBR - Reverse Breakdown Voltage (V) 5 4 3 2 1 0 0 25 50 75 100 125 150 175 TA - Ambient Temperature (ºC) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/14/20 TVS Diode Surface Mount – 600W > SMBJ-HRA Series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs 3°C/second max Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C tp TP Ramp-up TL Temperature (T) Reflow Condition Critical Zone TL to TP tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Polarity 0.003 ounce, 0.093 grams JEDEC DO214AA. Molded plastic body over glass passivated junction Color band denotes cathode except Bidirectional Temperature Cycling JESD22-A104 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 Weight Case Dimensions DO-214AA (SMB J-Bend) Cathode Band (for Uni-directional products only) C A B H D F E Dimensions Inches Millimeters Min Max Min Max A 0.077 0.086 1.950 2.200 B 0.160 0.180 4.060 4.570 C 0.130 0.155 3.300 3.940 2.440 D 0.084 0.096 2.130 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - G J K L I Solder Pads (all dimensions in mm) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/14/20 TVS Diode Surface Mount – 600W > SMBJ-HRA Series Part Numbering System SMBJ Part Marking System XXX C A -HR A Cathode Band (for Uni-directional products only) F Without Group B Test High Reliabilty 5% Voltage Tolerance XX BiI-Diractional YMXXX Voltage Series Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Component Package DO-214AA Part number SMBJxxxXX-HRA Quantity 3000 Packaging Option Tape & Reel - 12mm tape/13” reel Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.315 (8.0) 13” 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/14/20