SMBJ170CA-HR

TVS Diode Surface Mount – 600W > SMBJ-HR series SMBJ-HR Series RoHS Pb e3 Description The SMBJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 600 W PM(AV) 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only VF 3.5V V Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) Power Dissipation on Infinite Heat Sink at TA=50OC Operating Junction and Storage Temperature Range TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead RƟJL 20 °C/W Typical Thermal Resistance Junction to Ambient RƟJA 100 °C/W Notes: 1. Non-repetitive current pulse per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Features • 600W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 1µA above 12V • For surface mounted applications to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC 61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • Fast response time: typically less than 1.0ps from 0V to BV min • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • Glass passivated chip junction • High temperature soldering guaranteed: 260°C/40 seconds at terminals • Plastic package is flammability rated V-0 per UL 94 • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C. • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • UL Recognized to ANSI/ UL 497B: Protectors for Data Communications and Fire-Alarm Circuits. Applications TVS Components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/06/20 TVS Diode Surface Mount – 600W > SMBJ-HR series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) SMBJ5.0A-HR SMBJ6.0A-HR SMBJ6.5A-HR SMBJ7.0A-HR SMBJ7.5A-HR SMBJ8.0A-HR SMBJ8.5A-HR SMBJ9.0A-HR SMBJ10A-HR SMBJ11A-HR SMBJ12A-HR SMBJ13A-HR SMBJ14A-HR SMBJ15A-HR SMBJ16A-HR SMBJ17A-HR SMBJ18A-HR SMBJ20A-HR SMBJ22A-HR SMBJ24A-HR SMBJ26A-HR SMBJ28A-HR SMBJ30A-HR SMBJ33A-HR SMBJ36A-HR SMBJ40A-HR SMBJ43A-HR SMBJ45A-HR SMBJ48A-HR SMBJ51A-HR SMBJ54A-HR SMBJ58A-HR SMBJ60A-HR SMBJ64A-HR SMBJ70A-HR SMBJ75A-HR SMBJ78A-HR SMBJ85A-HR - SMBJ5.0CA-HR SMBJ6.0CA-HR SMBJ6.5CA-HR SMBJ7.0CA-HR SMBJ7.5CA-HR SMBJ8.0CA-HR SMBJ8.5CA-HR SMBJ9.0CA-HR SMBJ10CA-HR SMBJ11CA-HR SMBJ12CA-HR SMBJ13CA-HR SMBJ14CA-HR SMBJ15CA-HR SMBJ16CA-HR SMBJ17CA-HR SMBJ18CA-HR SMBJ20CA-HR SMBJ22CA-HR SMBJ24CA-HR SMBJ26CA-HR SMBJ28CA-HR SMBJ30CA-HR SMBJ33CA-HR SMBJ36CA-HR SMBJ40CA-HR SMBJ43CA-HR SMBJ45CA-HR SMBJ48CA-HR SMBJ51CA-HR SMBJ54CA-HR SMBJ58CA-HR SMBJ60CA-HR SMBJ64CA-HR SMBJ70CA-HR SMBJ75CA-HR SMBJ78CA-HR SMBJ85CA-HR SMBJ90CA-HR SMBJ100CA-HR SMBJ110CA-HR SMBJ120CA-HR SMBJ130CA-HR SMBJ150CA-HR SMBJ160CA-HR SMBJ170CA-HR Marking UNI BI KE KG KK KM KP KR KT KV KX KZ LE LG LK LM LP LR LT LV LX LZ ME MG MK MM MP MR MT MV MX MZ NE NG NK NM NP NR NT NV - AE AG AK AM AP AR AT AV AX AZ BE BG BK BM BP BR BT BV BX BZ CE CG CK CM CP CR CT CV CX CZ DE DG DK DM DP DR DT DV DX DZ EE EG EK EM EP ER Reverse Stand off Voltage VR (Volts) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 Breakdown Voltage VBR (Volts) @ IT Test Current IT MIN MAX (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Maximum Maximum Clamping Reverse Peak Voltage VC Leakage IR Pulse Current @ Ipp @ VR Ipp (A) (V) (µA) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.2 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Note: 1. Each lot of parts will pass group B test requirement. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/06/20 TVS Diode Surface Mount – 600W > SMBJ-HR series Screen Process 100% Vision Inspection MIL-STD-750 method 2074 100% High Temperature Storage Life (168hrs,175°C) MIL-STD-750 method 1031 100% X-RAY inspection MIL-STD-750 method 2076 100% Temperature Cycle Test (-55 to150°C, 20 cycles, dwell time 15 min) MIL-STD-750 method 1051 100% Reflow (2x) JEDEC J-STD-020 100% Surge Test (2x) MIL-STD-750 method 4066 100% HTRB 150°C Bias=VR(80% breakdown voltage, 96hrs, and each direction 96hrs for Bi-directional products) MIL–STD–750 method 1038 Final Electrical Test( 100% 3 sigma limit, 100% dynamic test and PAT limit) MIL-STD-750 method 4016.4021.4011 Note: Up-screen program can be specified by customer’s request via contacting Littelfuse service Group B Test Requirement Screen Method Condition Requirement Surge test 10/1000 µs Peak Pulse Waveform Maximum clamping Voltage (VC) @ Peak Pulse Current (IPP) Sample Size 45 perform 10x Accept 0 failures Burn - In (HTRB) MIL -STD-750, Method 1038.5 Applied voltage 100% VR@150°C Electrical test -- IR@VR, V(BR)@IT Sample size 45 340 hours (680 hours for bi-direction products, each direction 340 hours) Accept 0 failures Sample size 45 Accept 0 failures I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT V Vc VBR VR Ipp PPPM VR VBR VC IR VF IT IR IR IT VR VBR Vc V Ipp Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/06/20 TVS Diode Surface Mount – 600W > SMBJ-HR series Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 0.001 0.01 Figure 3 - Pulse Derating Curve IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 150 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) tr=10µsec TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 175 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Dissipation Derating Curve 100000 Uni-di PM(AV), Steady State Power Dissipation (W) 6 10000 onal V=0V Bi-direc Cj (pF) 1 Figure 4 - Pulse Waveform 100 nal V=0V 1000 100 Uni-di onal Bi-direc nal V=VR 10 1 0.1 td-Pulse Width (ms.) Time 1 10 1 00 VBR - Reverse Breakdown Voltage (V) 1000 5 4 3 2 1 0 0 25 50 75 100 125 150 175 TA - Ambient Temperature (ºC) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/06/20 TVS Diode Surface Mount – 600W > SMBJ-HR series Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz Soldering Parameters Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TL) to peak TS(max) to TL - Ramp-up Rate Reflow Lead–free assembly - Temperature (TL) (Liquidus) - Time (min to max) (ts) 3°C/second max 3°C/second max 217°C 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Physical Specifications Polarity 0.003 ounce, 0.093 grams JEDEC DO214AA. Molded plastic body over glass passivated junction Color band denotes cathode except Bidirectional Terminal Matte Tin-plated leads, Solderable per JESD22-B102 Weight Case tp TP Ramp-up TL Temperature (T) Reflow Condition Critical Zone TL to TP tL Ts(max) Ts(min) Ramp-down ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/06/20 TVS Diode Surface Mount – 600W > SMBJ-HR series Dimensions Dimensions DO-214AA (SMB J-Bend) C A B K J H L D I F E G Solder Pads Millimeters Max Min Max 0.077 0.086 1.950 2.200 B 0.160 0.180 4.060 4.570 C 0.130 0.155 3.300 3.940 2.440 A Cathode Band (for Uni-directional products only) Inches Min D 0.084 0.096 2.130 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - (all dimensions in mm) Part Numbering System SMBJ Part Marking System XXX C A -HR Cathode Band F (for uni-directional products only) High Reliability XX 5% Voltage Tolerance YMXXX Bi-Directional Voltage Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Series Packaging Part number Component Package Quantity Packaging Option Packaging Specification SMBJxxxXX-HR DO-214AA 3000 Tape & Reel - 12mm tape/13” reel EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.47 (12.0) Cathode 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/06/20