SMCG18A-HRA

TVS Diode Surface Mount – 1500W > SMCG-HRA series SMCG-HRA Series RoHS Pb e3 Description The SMCG-HRA series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation (IPP x VC)by 10/1000µs waveform (Fig.2)(Note 1), (Note 2) PPPM 1500 W Power Dissipation on infinite heat sink at TA=50OC PM(AV) 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 200 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional only VF 3.5 V Operating Junction and Storage Temperature Range TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead RƟJL 15 °C/W Typical Thermal Resistance Junction to Ambient RƟJA 75 °C/W Notes: 1. Non-repetitive current pulse per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only, duty cycle=4 per minute maximum. • High-Reliability upscreened for critical applications require higher reliability performance and low infant mortality failures. • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 1μA when VBR min>12V • Surface mount component to optimize board space • L bend lead forming gives best solderbility for High reliability application • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • Fast response time: typically less than 1.0ps from 0V to VBR min • 1500W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • VBR @TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • Glass passivated chip junction • High temperature soldering guaranteed: 260°C/10 seconds at terminals • Meet MSL level1, per J-STD-020 • Matte tin lead–free plated • Halogen free • RoHS compliant with exemption 7a and 7c-I • Pb-free E3 means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) Applications Functional Diagram TVS components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/22/20 TVS Diode Surface Mount – 1500W > SMCG-HRA series Electrical Characteristics Part Number (Uni) Part Number (Bi) Marking UNI BI Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) Agency Approval SMCG5.0A-HRA SMCG5.0CA-HRA GDEH BDEH 5.0 6.40 7.00 10 9.2 163.0 800 X SMCG6.0A-HRA SMCG6.0CA-HRA GDGH BDGH 6.0 6.67 7.37 10 10.3 145.7 800 X SMCG6.5A-HRA SMCG6.5CA-HRA GDKH BDKH 6.5 7.22 7.98 10 11.2 134.0 500 X SMCG7.0A-HRA SMCG7.0CA-HRA GDMH BDMH 7.0 7.78 8.60 10 12.0 125.0 200 X SMCG7.5A-HRA SMCG7.5CA-HRA GDPH BDPH 7.5 8.33 9.21 1 12.9 116.3 100 X SMCG8.0A-HRA SMCG8.0CA-HRA GDRH BDRH 8.0 8.89 9.83 1 13.6 110.3 50 X SMCG8.5A-HRA SMCG8.5CA-HRA GDTH BDTH 8.5 9.44 10.40 1 14.4 104.2 20 X SMCG9.0A-HRA SMCG9.0CA-HRA GDVH BDVH 9.0 10.00 11.10 1 15.4 97.4 10 X SMCG10A-HRA SMCG10CA-HRA GDXH BDXH 10.0 11.10 12.30 1 17.0 88.3 5 X SMCG11A-HRA SMCG11CA-HRA GDZH BDZH 11.0 12.20 13.50 1 18.2 82.5 1 X SMCG12A-HRA SMCG12CA-HRA GEEH BEEH 12.0 13.30 14.70 1 19.9 75.4 1 X SMCG13A-HRA SMCG13CA-HRA GEGH BEGH 13.0 14.40 15.90 1 21.5 69.8 1 X SMCG14A-HRA SMCG14CA-HRA GEKH BEKH 14.0 15.60 17.20 1 23.2 64.7 1 X SMCG15A-HRA SMCG15CA-HRA GEMH BEMH 15.0 16.70 18.50 1 24.4 61.5 1 X SMCG16A-HRA SMCG16CA-HRA GEPH BEPH 16.0 17.80 19.70 1 26.0 57.7 1 X SMCG17A-HRA SMCG17CA-HRA GERH BERH 17.0 18.90 20.90 1 27.6 54.4 1 X SMCG18A-HRA SMCG18CA-HRA GETH BETH 18.0 20.00 22.10 1 29.2 51.4 1 X SMCG20A-HRA SMCG20CA-HRA GEVH BEVH 20.0 22.20 24.50 1 32.4 46.3 1 X SMCG22A-HRA SMCG22CA-HRA GEXH BEXH 22.0 24.40 26.90 1 35.5 42.3 1 X SMCG24A-HRA SMCG24CA-HRA GEZH BEZH 24.0 26.70 29.50 1 38.9 38.6 1 X X SMCG26A-HRA SMCG26CA-HRA GFEH BFEH 26.0 28.90 31.90 1 42.1 35.7 1 SMCG28A-HRA SMCG28CA-HRA GFGH BFGH 28.0 31.10 34.40 1 45.4 33.1 1 X SMCG30A-HRA SMCG30CA-HRA GFKH BFKH 30.0 33.30 36.80 1 48.4 31.0 1 X SMCG33A-HRA SMCG33CA-HRA GFMH BFMH 33.0 36.70 40.60 1 53.3 28.2 1 X SMCG36A-HRA SMCG36CA-HRA GFPH BFPH 36.0 40.00 44.20 1 58.1 25.9 1 X X SMCG40A-HRA SMCG40CA-HRA GFRH BFRH 40.0 44.40 49.10 1 64.5 23.3 1 SMCG43A-HRA SMCG43CA-HRA GFTH BFTH 43.0 47.80 52.80 1 69.4 21.7 1 X SMCG45A-HRA SMCG45CA-HRA GFVH BFVH 45.0 50.00 55.30 1 72.7 20.6 1 X X SMCG48A-HRA SMCG48CA-HRA GFXH BFXH 48.0 53.30 58.90 1 77.4 19.4 1 SMCG51A-HRA SMCG51CA-HRA GFZH BFZH 51.0 56.70 62.70 1 82.4 18.2 1 X SMCG54A-HRA SMCG54CA-HRA GGEH BGEH 54.0 60.00 66.30 1 87.1 17.3 1 X SMCG58A-HRA SMCG58CA-HRA GGGH BGGH 58.0 64.40 71.20 1 93.6 16.1 1 X SMCG60A-HRA SMCG60CA-HRA GGKH BGKH 60.0 66.70 73.70 1 96.8 15.5 1 X SMCG64A-HRA SMCG64CA-HRA GGMH BGMH 64.0 71.10 78.60 1 103.0 14.6 1 X SMCG70A-HRA SMCG70CA-HRA GGPH BGPH 70.0 77.80 86.00 1 113.0 13.3 1 X SMCG75A-HRA SMCG75CA-HRA GGRH BGRH 75.0 83.30 92.10 1 121.0 12.4 1 X SMCG78A-HRA SMCG78CA-HRA GGTH BGTH 78.0 86.70 95.80 1 126.0 11.9 1 X SMCG85A-HRA SMCG85CA-HRA GGVH BGVH 85.0 94.40 104.00 1 137.0 11.0 1 X SMCG90A-HRA SMCG90CA-HRA GGXH BGXH 90.0 100.00 111.00 1 146.0 10.3 1 X SMCG100A-HRA SMCG100CA-HRA GGZH BGZH 100.0 111.00 123.00 1 162.0 9.3 1 X SMCG110A-HRA SMCG110CA-HRA GHEH BHEH 110.0 122.00 135.00 1 177.0 8.5 1 X SMCG120A-HRA SMCG120CA-HRA GHGH BHGH 120.0 133.00 147.00 1 193.0 7.8 1 X SMCG130A-HRA SMCG130CA-HRA GHKH BHKH 130.0 144.00 159.00 1 209.0 7.2 1 X © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/22/20 TVS Diode Surface Mount – 1500W > SMCG-HRA series Screen Process 100% vision inspection MIL-STD-750 method 2074 100%High Temperature Storage Life (168hrs,175C) MIL-STD-750 method 1031 100% X-RAY inspection MIL-STD-750 method 2076 100% Temperature cycle test (-55-150C, 20 cycles, dwell time 15 min) MIL-STD-750 method 1051 100% Reflow (2x) JEDEC J-STD-020 100% surge test (2x) MIL-STD-750 method 4066 100% HTRB(150C, Bias=VR(80% breakdown voltage), 96hrs),for Bi-direction products, 96hrs for each direction MIL–STD–750 method 1038 Final electrical test( 100% 3 sigma limit, 100% dynamic test and PAT limit) MIL-STD-750 method 4016.4021.4011 Note: Up-screen program can be specified by customer’s request by contacting Littelfuse customer service I-V Curve Characteristics Uni-directional I I Bi-directional Ipp Vc VBR VR IR VF IT IT IR Vc VBR VR V IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation (IPP x VC)-- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltagethat flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS TJ initial = Tamb 10 1 0.1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) continues on next page. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/22/20 TVS Diode Surface Mount – 1500W > SMCG-HRA series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform Figure 3 - Peak Pulse Power Derating Curve 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) 2 50 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 Figure 6 - Typical Transient Thermal Impedance Transient Thermal Impedance ( °C/W) Bi-directional V=0V Cj(pF) ( ) t-Time (ms) Uni-directional V=0V Uni-directional V=VR 100 Bi-directional V=VR 10 Half Value IPPM IPPM 0 100000 1000 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 175 Figure 5 - Typical Junction Capacitance 10000 tr=10µsec 100 10 1 0.1 0.01 1 0.001 1 10 100 1000 VBR - Reverse Breakdown Voltage(V) 0.01 0.1 1 10 100 1000 T P - Pulse Duraon (s) IFSM - Peak Forward Surge Current (A) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only 200 180 160 140 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/22/20 TVS Diode Surface Mount – 1500W > SMCG-HRA series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak Reflow Ramp-up TL 3°C/second max 3°C/second max TS(max) to TL - Ramp-up Rate - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 30 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C +0/-5 Polarity tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications 0.007 ounce, 0.21 grams JEDEC DO-215AB. Molded plastic body over glass passivated junction Color band denotes cathode for unidirectional components Case Critical Zone TL to TP °C Physical Specifications Weight tp TP Temperature (T) Reflow Condition High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 Dimensions DO-215AB (SMCG) Dimensions Cathode Band A C A B H N D F E I G Dimensions in inches and (millimeters) J K Seating Plane Inches Millimeters Min Max Min Max 0.115 0.125 2.920 3.170 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.075 0.095 1.900 2.410 E 0.038 0.058 0.970 1.470 F - 0.020 - 0.510 G 0.380 0.400 9.640 10.160 H 0.024 0.040 0.610 1.020 I 0.006 0.016 0.150 0.410 1.270 J - 0.050 - K - 0.310 - 7.870 L - 0.050 - 1.270 M - 0.125 - 3.170 N 0.002 0.008 0.050 0.200 L M Solder Pads © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/22/20 TVS Diode Surface Mount – 1500W > SMCG-HRA series Part Numbering System SMCG Part Marking System xxx C A -HR A Cathode Band (for Uni-directional products only) F Without Group B Test High Reliability 5% VBR Voltage Tolerance XXX Bi-Directional YMXXX VR Voltage Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Series Packaging Part number Component Package Quantity Packaging Option Packaging Specification SMCGxxxXX-HRA DO-215AB 1500 Tape & Reel – 24mm tape /13” reel EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.945 (24.0) 0.472 (12.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.800 (20.2) Arbor Hole Dia. 0.960 (24.4) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 04/22/20