SP1004-04VTG

TVS Diode Array Datasheet SP1004 Series 5pF 8kV Bidirectional TVS Array 6/25/2021 ESU270-54 N/A RoHS GREEN Pb Description The SP1004 are back-to-back zener diodes fabricated in a proprietary silicon avalanche technology protect each I/O pin to provide a high level of protection for electronic equipment that may experience destructive electrostatic discharges (ESD). These robust diodes can safely absorb repetitive ESD strikes at the maximum level specified in the IEC 61000-4-2 international standard (Level 4, ±8kV contact discharge) without performance degradation. Their very low loading capacitance also makes them ideal for protecting high-speed signal pins. Features & Benefits Additional Information ■ RoHS compliant and Leadfree ■ Low capacitance of 5pF (TYP) per I/O ■ ESD, IEC 61000-4-2, ±8kV contact, ±15kV air ■ Low leakage current of 1µA (MAX) at 5V ■ Capable of withstanding >1,000 ±8kV ESD strikes ■ Small SOT953 package ■ Lightning, IEC 61000-4-5, 2nd Edition, 2A (tp=8/20µs) Resources Accessories Applications Samples Pinout I/O 1 ■ MP3-PMPs ■ Digital cameras ■ DVD players ■ Set top boxes ■ Desktops ■ Notebooks ■ Mobile phones I/O 5 Application Example I/O 2 I /O 3 RCA jacks I /O 4 Audio codec Left - In Right - In Left - Out Right - Out Back panel (STB, TV) SOT953 Notes: 1 ■ AEC-Q101 Qualified Any of the 5 I/O pins can be tied to GND to provide 4 channels of bidirectional protection Functional Block Diagram 5 4 SP1004-04VTG (SOT953) Shield Ground 1 2 Signal Ground 3 Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. 1 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 04/14/21 TVS Diode Array Datasheet SP1004 Series 5pF 8kV Bidirectional TVS Array Absolute Maximum Ratings Symbol Parameter Value Units IPP Peak Pulse Current (tp=8/20μs) 2.0 A TOP Operating Temperature –40 to 125 °C TSTOR Storage Temperature –55 to 150 °C Caution: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Thermal Information Parameter Storage Temperature Range Rating Units –55 to 150 °C Maximum Junction Temperature 150 °C Maximum Lead Temperature (Soldering 20-40s) 260 °C Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions Min 6.0 VR IR=1mA Reverse Standoff Voltage1 Reverse Voltage Drop VRWM IR≤1µA Reverse Leakage Current1 ILEAK 1 Clamp Voltage2 VC RDYN ESD Withstand Voltage1,2 VESD Diode Capacitance1,2 Max VR=5V IPP=1A, tp=8/20µs Dynamic Resistance Typ Units 9.5 V 6.0 V 0.1 µA 10 V IPP=2A, tp=8/20µs 12 V (VC2 - VC1) / (IPP2 - IPP1) 2.0 Ω IEC 61000-4-2 (Contact Discharge)3 ±8 kV IEC 61000-4-2 (Air Discharge) ±15 kV CD Reverse Bias=0V 6 7 pF Reverse Bias=1.5V 5 6 pF Note: 1 Parameter specified with pin 2 grounded externally. 2 Parameter is guaranteed by design and/or device characterization. 3 Capable of withstanding >1,000 pulses at 1s intervals. Insertion Loss (S21) 7.0 5 6.0 0 5.0 -5 Attenuation (dB) Capacitance (pF) Capacitance vs. Reverse Bias 4.0 3.0 2.0 -10 -15 -20 -25 1.0 -30 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 10 5.0 100 1000 10000 Frequency (MHz) DC Bias (V) 2 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 04/14/21 TVS Diode Array Datasheet SP1004 Series 5pF 8kV Bidirectional TVS Array Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow tP TP - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Temperature Reflow Condition Critical Zone TL to TP Ramp-up TL TS(max) tL Ramp-do Ramp-down Preheat TS(min) 25 tS time to peak temperature Time Package Dimensions — SOT953 D SOT953 Symbol e Millimeters E E1 Min B Max 0.44 0.5 0.170 0.020 B 0.10 0.20 0.004 0.008 c 0.05 0.15 0.002 0.006 D 0.95 1.05 0.037 0.041 E 0.95 1.05 0.037 0.041 E1 0.75 0.85 0.029 0.033 L C Inches Min A e A Max 0.35 BSC 0.05 0.15 0.014 BSC 0.002 0.006 L 3 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 04/14/21 TVS Diode Array Datasheet SP1004 Series 5pF 8kV Bidirectional TVS Array Product Characteristics Part Numbering System SP 1004 – 04 V T G TVS Diode Arrays (SPA® Diodes) G= Green T= Tape & Reel Series Pre-Plated Frame Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Substitute Material Silicon Body Material Molded Epoxy Flammability UL 94 V-0 Notes : 1. All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form. 5. Package surface matte finish VDI 11-13. Package V: SOT953 Number of Channels Lead Plating Part Marking System N2 Ordering Information Part Number Package Marking Min. Order Qty. SP1004-04VTG SOT953 N2 8000 Embossed Carrier Tape & Reel Specification – SOT953 PO t E P2 o/ D Symbol Millimetres Min Max Min Max E 1.65 1.85 0.065 0.073 F 3.45 3.55 0.136 0.140 D1 0.45 0.55 0.018 0.022 4.10 0.154 1.50 min D W P0 10P0 P BO F oD1 / AO Inches 3.90 0.059 min 40.0 ± 0.20 0.161 1.575 ± 0.008 P 1.95 2.05 0.077 0.081 P2 1.95 2.05 0.077 0.081 W 7.90 8.20 0.311 0.323 A0 1.11 1.21 0.044 0.048 B0 1.11 1.21 0.044 0.048 K0 0.58 0.68 0.023 0.027 0.22 max 0.009 max KO t Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. 4 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 04/14/21