SP4021-01FTG

TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4021 Series SP4021 Series 2.5pF, 25A Discrete TVS Diode RoHS Pb GREEN Description The SP4021 components integrate low capacitance steering diodes with one or two avalanche breakdown diodes for unidirectional or bidirectional protection, respectively, to protect against ESD and lightning induced surge events. These components can safely absorb up to 25A per IEC 61000-4-5 (tp=8/20μs) without performance degradation and a minimum ±30kV ESD per IEC 610004-2 International Standard. The low loading capacitance and high surge capability make it ideal for protecting telecommunication ports such as Ethernet and other high speed data interfaces. Pinout Features • ESD, IEC 61000-4-2, ±30kV contact, ±30kV air • EFT, IEC 61000-4-4, 40A (5/50ns) 1 • Lightning, 25A (8/20 as defined in IEC 61000-4-5 2nd edition) • Low capacitance of 2.5pF (@ VR=0V) Bidirectional configuration • Small SOD323 package fits 0805 footprints • Moisture Sensitivity Level (MSL-1) • AEC-Q101 Qualified • Halogen free, Lead free, and RoHS compliant • Low leakage current • Unidirectional and 2 Functional Block Diagram 1 Applications 1 •10/100/1000 Ethernet •Computers and Peripherals •T1/E1/T3/E3 •Instrumentation •USB 1.1/2.0 •Medical Equipment •Power Ports •USB 3.0 and 3.1 Additional Information 2 2 Unidirectional Bidirectional SP4021-01FTG SP4021-01FTG-C Datasheet Resources Samples Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/19/19 TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4021 Series Absolute Maximum Ratings Symbol Parameter Value Units IPP Peak Current (tp=8/20μs) 25 A PPk Peak Pulse Power (tp=8/20μs) 750 W TOP Operating Temperature -40 to 125 °C TSTOR Storage Temperature -55 to 150 °C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions Min 6.3 Breakdown Voltage Typ Max Units VBR IR=2μA Reverse Standoff Voltage VRWM IR=1μA 5.0 V Reverse Leakage Current ILEAK VR=5.0V 0.5 μA IPP=1A, tp=8/20µs, Fwd 9.3 V VC IPP=10A, tp=8/20µs, Fwd 14.0 V Clamp Voltage1 Dynamic Resistance2 RDYN ESD Withstand Voltage1 VESD IPP=24A, tP=8/20μs, Fwd 19.6 V TLP, tP=100ns 0.35 Ω IEC 61000-4-2 (Contact Discharge) ±30 IEC 61000-4-2 (Air Discharge) ±30 CD Diode Capacitance1 V Reverse Bias=0V, f=1MHz kV kV 2.5 pF Note: 1. Parameter is guaranteed by design and/or component characterization. 2. Transmission Line Pulse (TLP) with 100ns width and 200ps rise time. Normalized Capacitance vs. Bias Voltage 3.5 Normalized Capacitance 3.0 SP4021-01FTG SP4021-01FTG-C 2.5 2.0 1.5 1.0 0.5 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Bias Voltage (V) © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/19/19 TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4021 Series Positive Transmission Line Pulsing (TLP) Plot Negative Transmission Line Pulsing (TLP) Plot 20 0 18 -2 -4 14 -6 TLP Current (A) TLP Current (A) 16 12 10 8 6 -8 -10 -12 -14 4 -16 2 -18 0 0 2 4 6 8 10 12 14 16 18 -20 20 -20 -18 -16 -14 TLP Voltage (V) -12 -10 -8 -6 -4 -2 0 TLP Voltage (V) Pulse Waveform Clamping Voltage vs. IPP 110% 24.0 100% Clamp Voltage (VC) 20.0 90% 80% Percent of IPP 16.0 12.0 8.0 70% 60% 50% 40% 30% 4.0 20% 10% 0.0 1.0 5.0 10.0 15.0 20.0 0% 25.0 0.0 5.0 10.0 15.0 Peak Pulse Current-IPP (A) 20.0 25.0 30.0 Time (μs) Soldering Parameters Pre Heat Pb – Free assembly - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate Reflow 3°C/second max - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C tP TP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL T S(max) tL Ramp-dow Ramp-down Preheat T S(min) tS 25 time to peak temperature Time Product Characteristics Lead Plating Matte Tin Lead Material Alloy 42 Lead Coplanarity 0.0004 inches (0.102mm) Substrate Material Silicon Body Material Molded Compound UL Recognized compound meeting flammability rating V-0 Flammability © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/19/19 TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4021 Series Part Numbering System Part Marking System SP 4021 SP4021-01FTG 05 1 2 5C 01 F T G C Blank= Unidirectional C= Bidirectional G= Green TVS Diode Arrays (SPA® Diodes ) Series Number of Channels SP4021-01FTG-C 1 – T= Tape & Reel Package F: SOD323 Ordering Information 2 Part Number Package Min. Order Qty. SP4021-01FTG SOD323 3000 SP4021-01FTG-C SOD323 3000 Package Dimensions -SOD323 E D b L1 L Recommended Solder Pad 1.79 0.45 0.49 c 0.2 Symbol A E1 L SOD323 A2 A1 Millimeters Inches Min Max Min Max A 0.8 1.00 0.031 0.039 A1 0.00 0.10 0.000 0.004 A2 0.80 0.90 0.031 0.035 b 0.25 0.35 0.010 0.014 c 0.08 0.15 0.003 0.006 D 1.20 1.40 0.047 0.055 E 1.60 1.80 0.063 0.071 E1 2.50 2.70 0.098 0.106 L1 0.25 0.40 0.010 0.016 1.14 2.28 2.77 Unit: mm Embossed Carrier Tape & Reel Specification — SOD323 Symbol Component Orientation in Tape ,Ref. ,Ref. ,Ref. Pin1 8mm TAPE AND REEL Millimeters A0 1.46+/-0.10 B0 2.90+/-0.10 W 8.0+0.3/-0.10 D0 1.50+0.10 D1 0.45min/1.15max E1 1.75+/-0.10 E2 - F 3.50+/-0.10 P0 4.00+/-0.10 P 4.00+/-0.10 P1 2.00+/-0.05 K0 1.25+/-0.10 T 0.254+/-0.02 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/19/19