SP4022-01FTG

TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4022 Series SP4022 Series 1.3pF, 15A Discrete TVS Diode RoHS Pb GREEN Description The SP4022 series integrate low capacitance steering diodes with one or two avalanche breakdown diodes for unidirectional or bidirectional protection, respectively, to protect against ESD and lightning induced surge events. These devices can safely absorb up to 15A per IEC 61000-4-5 2nd Edition (tp=8/20μs) without performance degradation and a minimum ±30kV ESD per IEC610004-2 International Standard. The low loading capacitance and high surge capability make it ideal for protecting telecommunication ports such as xDSL and other high voltage, high speed legacy interfaces. Pinout Features • ESD, IEC 61000-4-2, ±30kV contact, ±30kV air Pin 1 • EFT, IEC 61000-4-4, 40A (5/50ns) • Lightning, 15A (8/20μs as defined in IEC 61000-4-5 2nd edition) • Low capacitance of 1.3pF (@ VR=0V) • Low leakage current • Unidirectional and Bidirectional configuration • Small SOD323 package fits 0805 footprints • AEC-Q101 qualified • Moisture Sensitivity Level (MSL-1) Pin 2 Cathode polarity for unidirectional only Functional Block Diagram 1 Applications 1 • xDSL Interfaces • Security Equipment • RS-232 • Instrumentation • RS-485 • Medical Equipment • Power Ports • Computers and Peripherals Additional Information 2 Unidirectional SP4022-01FTG SP4021-01FTG 2 Bidirectional SP4022-01FTG-C SP4021-01FTG-C Datasheet Resources Samples Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/20 TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4022 Series Absolute Maximum Ratings Symbol Parameter Value Units IPP Peak Current (tp=8/20μs) 15 A PPk Peak Pulse Power (tp=8/20μs) 500 W TOP Operating Temperature -40 to 150 °C TSTOR Storage Temperature -55 to 150 °C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Characteristics (TOP=25ºC) Parameter Symbol Reverse Standoff Voltage Test Conditions Min Typ Max Units VRWM IR=1μA - - 12 V Breakdown Voltage VBR IR=1mA 13.3 - - V Reverse Leakage Current ILEAK VC Clamp Voltage1 Dynamic Resistance2 VESD Diode Capacitance - 0.1 μA - 19 - V IPP=2A, tp=8/20µs, Fwd - 20 - V IPP=10A, tP=8/20μs, Fwd - 28 - V 35 - 33 TLP tp=100ns - 0.5 - Ω IEC 61000-4-2 (Contact Discharge) ±30 - - kV IEC 61000-4-2 (Air Discharge) ±30 - - kV Reverse Bias=0V, f=1MHz - 1.3 2 pF CD 1 - IPP=15A, tp=8/20μs, Fwd RDYN ESD Withstand Voltage1 VR12V IPP=1A, tp=8/20µs, Fwd Note: 1. Parameter is guaranteed by design and/or component characterization. 2. Transmission Line Pulse (TLP) with 100ns width and 200ps rise time. 8/20 µs Pulse Waveform Capacitance vs. Reverse Bias 3.0 110% 100% 2.5 90% 2.0 70% Capacitance (pF) Percent of IPP 80% 60% 50% 40% 30% 20% 1.5 1.0 0.5 10% 0% 0.0 5.0 10.0 15.0 Time (μs) 20.0 25.0 30.0 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 Bias Voltage (V) © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/20 TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4022 Series Clamping Voltage vs. Peak Pulse Current Transmission Line Pulsing (TLP) Plot 25 40.0 20 30.0 25.0 TLP Current (A) Clamp Voltage (VC ) 35.0 20.0 15.0 10.0 15 10 5 5.0 0.0 3 5 7 9 Peak Pulse Current-I 11 PP 13 Pre Heat Pb – Free assembly 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max Reflow 5 10 15 20 25 30 40 50 Product Characteristics - Temperature Min (Ts(min)) TS(max) to TL - Ramp-up Rate 0 TLP Volts (V) Soldering Parameters Reflow Condition 0 15 (A) Lead Plating Matte Tin Lead Material Alloy 42 Lead Coplanarity 0.0004 inches (0.102mm) Substrate Material Silicon Body Material Molded Compound UL Recognized compound meeting flammability rating V-0 Flammability 3°C/second max - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C tP TP Critical Zone TL to TP Ramp-up Temperature 1 TL T S(max) tL Ramp-dow Ramp-down Preheat T S(min) tS 25 time to peak temperature Time © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/20 TVS Diode Array (SPA® Diodes) Lightning Surge Protection- SP4022 Series Part Marking System Part Numbering System SP 4022 SP4022-01FTG 12 01 F T G – C Blank= Unidirectional C= Bidirectional G= Green T= Tape & Reel TVS Diode Arrays (SPA® Diodes ) Series Number of Channels 2 1 – SP4022-01FTG-C Package F: SOD323 Ordering Information 12C 2 1 Part Number Package Min. Order Qty. SP4022-01FTG SOD323 3000 SP4022-01FTG-C SOD323 3000 Package Dimensions -SOD323 SOD323 E A2 D b A1 Symbol A 0.2 E1 L1 Recommended Solder Pad 1.79 c 0.45 0.49 Millimeters Inches Min Max Min Max A 0.80 1.00 0.031 0.039 A1 0.00 0.10 0.000 0.004 A2 0.80 0.90 0.031 0.035 b 0.25 0.35 0.010 0.014 c 0.08 0.15 0.003 0.006 D 1.20 1.40 0.047 0.055 E 1.60 1.80 0.063 0.071 E1 2.50 2.70 0.098 0.106 L1 0.25 0.40 0.010 0.016 1.14 2.28 2.77 Note: Note: Cathode mark is for unidirectional version Cathode mark is used for unidirectional version Unit: mm Embossed Carrier Tape & Reel Specification — SOD323 Symbol Component Orientation in Tape ,Ref. ,Ref. Pin1 ,Ref. 8mm TAPE AND REEL Millimeters A0 1.46+/-0.10 B0 2.90+/-0.10 W 8.0+0.3/-0.10 D0 1.50+0.10 D1 0.45min/1.15max E1 1.75+/-0.10 E2 - F 3.50+/-0.10 P0 4.00+/-0.10 P 4.00+/-0.10 P1 2.00+/-0.05 K0 1.25+/-0.10 T 0.254+/-0.02 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/05/20