SRR6012D1TP

Teccor® brand Thyristors 12 Amp Standard SCR SRR6012xx Series RoHS Description Excellent unidirectional switches for phase control and general switching applications such as heating, motor control controls, converters / rectifiers and capacitive discharge ignitions. Sensitive gate SCRs are easily triggered with microAmps of current as furnished by sense coils, proximity switches, and microprocessors. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits • RoHS compliant Main Features Symbol IT(RMS) VDRM /VRRM IGT Value Unit 12 A 600 V 6 mA • Glass – passivated junctions • Voltage capability up to 600 V • Surge capability up to 120 A Applications Typical applications includes capacitive discharge system for motorcycle engine CDI, portable generator engine ignition, strobe lights and nailers, as well as generic rectifiers, battery voltage regulators and converters. Also controls for power tools, home/brown good and white goods appliances. Schematic Symbol A K G Absolute Maximum Ratings — Standard SCRs Parameter Test Conditions SRR6012x1 Unit IT(RMS) Symbol RMS on-state current TC = 105°C 12 A IT(AV) Average on-state current TC = 105°C 7.68 A ITSM Peak non-repetitive surge current single half cycle; f = 50Hz; TJ (initial) = 25°C single half cycle; f = 60Hz; TJ (initial) = 25°C I2t I2t Value for fusing tp = 8.3 ms 60 A2s Critical rate-of-rise of on-state current f = 60 Hz TJ = 125°C 100 A/μs Peak gate current TJ = 125°C 2 A Average gate power dissipation TJ = 125°C 0.5 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 125 °C di/dt IGM PG(AV) Tstg TJ SRR6012xx Series 100 A 120 ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 12 Amp Standard SCR Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Standard SCRs Symbol Test Conditions SRR6012x1 Unit MIN. 1.5 mA MAX. 6 mA MAX. 1.5 V IGT VD = 12V RL = 60 Ω VGT VD = 12V RL = 60 Ω dv/dt VD = VDRM; gate open; TJ = 100°C VGD VD = VDRM; RL = 3.3 kΩ; TJ = 125°C MIN. 0.2 V IT = 200mA (initial) MAX. 30 mA (1) MAX. 35 μs TYP. 2 μs IH tq tgt 300 MIN. VD = VDRM; gate open; TJ = 125°C IG = 2 x IGT; PW = 15µs; IT = 20A V/μs 225 NOTE: (1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs Static Characteristics Symbol Test Conditions VTM IT = 24A; tp = 380 µs Value Unit 1.8 V MAX. TJ = 25°C IDRM / IRRM 10 TJ = 100°C VDRM / VRRM 200 MAX. TJ = 125°C μA 500 Thermal Resistances Symbol Rθ(J-C) Parameter Value Unit Junction to case (AC) 1.45 °C/W Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature (Sensitive SCR) Figure 2: N  ormalized DC Gate Trigger Current vs. Junction Temperature (Standard SCR) 4.0 Ratio of IGT / IGT (TJ = 25°C) Ratio of IGT / IGT (TJ = 25°C) 4.0 3.0 2.0 1.0 0.0 -40 -15 10 35 60 Junction Temperature (TJ) -- (°C) SRR6012xx Series 85 110 3.0 2.0 1.0 0.0 -40 -15 10 35 60 85 110 125 Junction Temperature (TJ) -- (°C) ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 12 Amp Standard SCR Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature Figure 4: N  ormalized DC Holding Current vs. Junction Temperature 2.0 Ratio of IH / IH (TJ = 25°C) Ratio of VGT / VGT (TJ = 25°C) 2.0 1.5 1.0 0.5 0.0 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 110 125 -40 -15 10 Junction Temperature (TJ) -- (°C) Figure 5: On-State Current vs. On-State Voltage (Typical) 85 110 125 12 TJ = 25ºC 11 28 10 24 Average On-State Power Dissipation [PD(AV)] -- (Watts) Instantaneous On-state Current (iT) – Amps 60 Figure 6: P  ower Dissipation (Typical) vs. RMS On-State Current 32 20 16 12 8 4 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 9 8 7 6 5 4 3 2 1 0 1.6 0 1 2 Instantaneous On-state Voltage (vT) – Volts 3 4 5 6 7 8 9 10 11 12 RMS On-State Current [IT(RMS)] -- (Amps) Figure 7: Maximum Allowable Case Temperature vs. RMS On-State Current Figure 8: M  aximum Allowable Case Temperature vs. Average On-State Current 130 130 125 125 120 Maximum Allowable Case Temperature (TC) - °C 35 Junction Temperature (TJ) -- (°C) 120 Maximum Allowable Case Temperature (TC) - °C 115 110 105 100 95 90 85 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 80 75 1 2 3 4 105 100 95 90 85 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING 75 5 6 7 8 9 10 RMS On-State Current [IT(RMS)] - Amps SRR6012xx Series 110 80 70 0 115 11 12 70 0 1 2 3 4 5 6 7 8 Average On-State Current [IT(AVE)] - Amps ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 12 Amp Standard SCR Figure 9: Peak Capacitor Discharge Current Figure 10: P  eak Capacitor Discharge Current Derating 1.2 1.0 Normalized Peak Current Peak Discharge Current (ITM) - Amps 1000 100 ITRM 0.8 0.6 0.4 0.2 tW 10 0.5 0.0 10.0 1.0 0 50.0 Pulse Current Duration (tW) - ms 25 50 75 100 150 125 Case Temperature (TC) - °C Figure 11: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. G  ate control may be lost during and immediately following surge current interval. 2. O  verload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 1 10 100 1000 Surge Current Duration -- Full Cycles SRR6012xx Series ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 12 Amp Standard SCR Soldering Parameters tP Pb – Free assembly Reflow Condition Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification V-0 Temperature TP Ramp-up TL tL TS(max) Preheat TS(min) 25 tS time to peak temperature Copper Alloy Time Environmental Specifications Test AC Blocking Lead Material Ramp-do Ramp-down Temperature Cycling Temperature/ Humidity Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage 1008 hours; -40°C Autoclave EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E SRR6012xx Series ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 12 Amp Standard SCR Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount Anode E D 6.71 .264 5.28 .208 TC MEASURING POINT Inches Dimension Typ Max Min A 0.037 0.040 0.043 0.94 1.01 1.09 B 0.235 0.243 0.245 5.97 6.16 6.22 A 6.71 .264 5.34 .210 B C P Q Cathode GATE F Anode 1.60 .063 1.80 .071 AREA : 0.040 IN2 3 .118 G 4.60 .181 I L O K J H M N Millimeters Min Typ Max C 0.106 0.108 0.113 2.69 2.74 2.87 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.65 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.33 2.41 I 0.176 0.179 0.184 4.47 4.55 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.51 0.58 M 0.000 0.000 0.004 0.00 0.00 0.10 N 0.021 0.026 0.027 0.53 0.67 0.69 O 0° 0° 5° 0° 0° 5° P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 Packing Options Part Number Marking Weight Packing Mode Base Quantity SRR6012D1TP SRR6012D1 SRR6012D1RP SRR6012D1 0.3 g Tube 750 (75 per tube) 0.3 g Embossed Carrier 2500 Part Numbering System Part Marking System SRR 60 12 D 1 RP DEVICE TYPE SRR: SCR VOLTAGE RATING 60 : 600V CURRENT 12: 12A SRR6012xx Series SRR6012D1 PACKAGING OPTIONS RP: Reel Pack TP: Tube Pack SENSITIVE TYPE 1: 6mA PACKAGE TYPE D : TO-252 (DPAK) YMLDD ® Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 12 Amp Standard SCR TO-252 Embossed Carrier Reel Pack (RP) Specifications * Cover tape 0.512 (13.0) Arbor Hole Dia. 0.315 (8.0) Cathode XXXXXX 0.059 Dia (1.5) DC DC XX XXXXXX * DC 0.524 (13.3) XX 0.63 (16.0) XXXXXX Gate XX 0.157 (4.0) XXXXXX Meets all EIA-481-2 Standards Anode 12.99 (330.0) Dimensions are in inches (and millimeters). 0.64 (16.3) Direction of Feed SRR6012xx Series ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16