SRR6016D1TP

Teccor® brand Thyristors 16 Amp Standard SCR SRR6016xx Series RoHS Description Excellent unidirectional switches for phase control and general switching applications such as heating, motor control controls, converters / rectifiers and capacitive discharge ignitions. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits • RoHS compliant • Glass – passivated junctions Main Features • Voltage capability up to 600 V • Surge capability up to 160 A Applications Symbol IT(RMS) VDRM /VRRM IGT Value Unit 16 A 600 V 6 mA Typical applications includes capacitive discharge system for motorcycle engine CDI, portable generator engine ignition, strobe lights and nailers, as well as generic rectifiers, battery voltage regulators and converters. Also controls for power tools, home/brown good and white goods appliances. Schematic Symbol A K G Absolute Maximum Ratings — Standard SCRs Symbol Parameter Test Conditions SRR6016x1 Unit IT(RMS) RMS on-state current TC = 100°C 16 A IT(AV) Average on-state current TC = 100°C 10.24 A ITSM Peak non-repetitive surge current single half cycle; f = 50Hz; TJ (initial) = 25°C single half cycle; f = 60Hz; TJ (initial) = 25°C I2t I2t Value for fusing tp = 8.3 ms 107 A2s Critical rate-of-rise of on-state current f = 60 Hz TJ = 125°C 100 A/μs Peak gate current TJ = 125°C 2 A Average gate power dissipation TJ = 125°C 0.5 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 125 °C di/dt IGM PG(AV) Tstg TJ SRR6016xx Series 132 A 160 ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 16 Amp Standard SCR Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Standard SCRs Symbol Test Conditions SRR6016x1 Unit MIN. 1.5 mA MAX. 6 mA MAX. 1.5 V IGT VD = 12V RL = 60 Ω VGT VD = 12V RL = 60 Ω dv/dt VD = VDRM; gate open; TJ = 100°C VGD VD = VDRM; RL = 3.3 kΩ; TJ = 125°C MIN. 0.2 V IT = 200mA (initial) MAX. 40 mA (1) MAX. 35 μs TYP. 2 μs MIN. VD = VDRM; gate open; TJ = 125°C IH tq tgt 300 IG = 2 x IGT; PW = 15µs; IT = 20A V/μs 225 NOTE: (1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs Static Characteristics Symbol Test Conditions VTM IT = 32A; tp = 380 µs Value Unit 1.8 V MAX. TJ = 25°C IDRM / IRRM 10 TJ = 110°C VDRM / VRRM 500 MAX. TJ = 125°C μA 1000 Thermal Resistances Symbol Rθ(J-C) Parameter Value Unit Junction to case (AC) 1.50 °C/W Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: N  ormalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25°C) Ratio of IGT / IGT (TJ = 25°C) 2.0 1.5 1.0 0.5 1.5 1.0 0.5 0.0 0.0 -40 -15 10 35 60 Junction Temperature (TJ ) - (°C) SRR6016xx Series 85 100 125 -40 -15 10 35 60 85 110 125 Junction Temperature (TJ) - (°C) ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 16 Amp Standard SCR Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: O  n-State Current vs. On-State Voltage (Typical) 60 2.0 TJ = 25°C 1.5 Instantaneous On-state Current (i T) – Amps Ratio of IH / IH (TJ = 25°C) 50 1.0 0.5 40 30 20 10 0.0 -40 -15 10 35 60 85 110 0 125 0.6 0.7 Junction Temperature (TJ ) - (°C) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 Instantaneous On-state Voltage (vT) – Volts Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Figure 6: M  aximum Allowable Case Temperature vs. RMS On-State Current 16 130 14 Maximum Allowable Case Temperature (TC)- °C 120 12 Average On-State Power Dissipation [PD(AV)] - (Watts) 10 8 6 4 110 100 90 80 70 2 60 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 0 2 4 0 0 2 4 6 8 10 RMS On-State Current [I T(RMS)] - (Amps) 12 14 8 10 12 14 16 RMS On-State Current [IT(RMS)] - Amps 16 Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current 6 Figure 8: P  eak Capacitor Discharge Current 1000 Peak Discharge Current (ITM) - Amps 130 Maximum Allowable Case Temperature (TC) - °C 120 110 100 90 80 70 60 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° 0 1 2 3 4 5 100 ITRM tW 10 05 . 6 7 8 9 10 11 5 .0 25.0 50.0 Pulse Current Duration (tw) - ms Average On-State Current [IT(AVE)] - Amps SRR6016xx Series ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 16 Amp Standard SCR Figure 9: Peak Capacitor Discharge Current Derating 1.2 Normalized Peak Current 1.0 0.8 0.6 0.4 0.2 0.0 0 25 50 75 100 125 150 Case Temperature (TC) - °C Figure 10: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM ) – Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature 100 Notes: 1. G  ate control may be lost during and immediately following surge current interval. 2. O  verload may not be repeated until junction temperature has returned to steady-state rated value. 10 1 1 SRR6016xx Series 10 10 0 Surge Current Duration - Full Cycles 10 0 0 ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 16 Amp Standard SCR Soldering Parameters 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification V-0 Temperature Pre Heat - Temperature Min (Ts(min)) tP TP Pb – Free assembly Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 tS time to peak temperature Copper Alloy Time Environmental Specifications Test AC Blocking Lead Material Ramp-do Ramp-down Temperature Cycling Temperature/ Humidity Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage 1008 hours; -40°C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E SRR6016xx Series ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 16 Amp Standard SCR Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount E D Anode 6.71 .264 5.28 .208 TC MEASURING POINT Dimension A 6.71 .264 5.34 .210 B C P Q Cathode GATE F Anode 1.60 .063 1.80 .071 AREA : 0.040 IN2 3 .118 G 4.60 .181 I L O K J H M N Inches Millimeters Min Typ Max Min Typ Max A 0.040 0.043 0.050 1.02 1.09 1.27 B 0.235 0.243 0.245 5.97 6.16 6.22 C 0.106 0.108 0.113 2.69 2.74 2.87 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.65 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.33 2.41 I 0.176 0.179 0.184 4.47 4.55 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.038 0.040 0.044 0.97 1.02 1.12 L 0.018 0.020 0.023 0.46 0.51 0.58 M 0.000 0.000 0.004 0.00 0.00 0.10 N 0.021 0.026 0.027 0.53 0.67 0.69 O 0° 0° 5° 0° 0° 5° P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 Packing Options Part Number Marking Weight Packing Mode Base Quantity SRR6016D1TP SRR6016D1 SRR6016D1RP SRR6016D1 0.3 g Tube 750 (75 per tube) 0.3 g Embossed Carrier 2500 Part Numbering System Part Marking System SRR 60 16 D 1 RP DEVICE TYPE SRR: SCR VOLTAGE RATING 60 : 600V CURRENT 16: 16A SRR6016xx Series SRR6016D1 PACKAGING OPTIONS RP: Reel Pack TP: Tube Pack SENSITIVE TYPE 1: 6mA PACKAGE TYPE D : TO-252 (DPAK) YMLDD ® Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16 Teccor® brand Thyristors 16 Amp Standard SCR TO-252 Embossed Carrier Reel Pack (RP) Specifications * Cover tape 0.512 (13.0) Arbor Hole Dia. 0.315 (8.0) Cathode XXXXXX 0.059 Dia (1.5) DC DC XX XXXXXX * DC 0.524 (13.3) XX 0.63 (16.0) XXXXXX Gate XX 0.157 (4.0) XXXXXX Meets all EIA-481-2 Standards Anode 12.99 (330.0) Dimensions are in inches (and millimeters). 0.64 (16.3) Direction of Feed SRR6016xx Series ©2016 Littelfuse, Inc Specifications are subject to change without notice. Revised: 06/29/16