TP6KE62A

TVS Diode Datasheet TP6KE Series Axial Leaded – 600W Pb RoHS e3 Description Bi-directional The AEC-Q101 qualified TP6KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features & Benefits Uni-directional Additional Information ■ Hi reliability application and automotive grade AEC-Q101 qualified ■ EFT protection of data lines in accordance with IEC 61000-44 (IEC801-4) ■ Glass passivated chip junction in DO-15 Package ■ Low incremental surge resistance ■ 600W peak pulse capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% ■ High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”,(9.5mm) lead length, 5 lbs., (2.3kg) tension ■ Fast response time: typically less than 1.0ps from 0 Volts to BV min ■ Excellent clamping capability Resources Accessories ■ Typical failure mode is short from over-specified voltage or current Samples ■ Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c ■ IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) Agency Approvals Agency ■ ESD protection of data lines in accordance with IEC 61000-42 (IEC801-2) Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Value Unit PPPM 600 W Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC (Fig. 6) PD 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only VF 3.5 V TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RuJL 20 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Operating Junction and Storage Temperature Range ■ Plastic package has underwriters laboratory flammability classification 94VO ■ Lead-free matte tin plated package ■ Halogen free and RoHS compliant Applications Symbol Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2) (Note 1) ■ VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25))(αT:Temperature Coefficient, typical value is 0.1%) TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Functional Diagram Bi-directional Cathode Anode Uni-directional Notes: 1. Non-repetitive current pulse, per Fig. 4 and derated above TJ (initial) = 25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. 1 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 06/10/21 TVS Diode Datasheet TP6KE Series Axial Leaded – 600W Electrical Characteristics (TA=25°C unless otherwise noted) Part Number (Uni) TP6KE13A TP6KE15A TP6KE16A TP6KE18A TP6KE20A TP6KE22A TP6KE24A TP6KE27A TP6KE30A TP6KE33A TP6KE36A TP6KE39A TP6KE43A TP6KE47A TP6KE51A TP6KE56A TP6KE62A TP6KE68A TP6KE75A TP6KE82A TP6KE91A Part Number (Bi) Breakdown Voltage VBR (Volts) @ IT TP6KE13CA TP6KE15CA TP6KE16CA TP6KE18CA TP6KE20CA TP6KE22CA TP6KE24CA TP6KE27CA TP6KE30CA TP6KE33CA TP6KE36CA TP6KE39CA TP6KE43CA TP6KE47CA TP6KE51CA TP6KE56CA TP6KE62CA TP6KE68CA TP6KE75CA TP6KE82CA TP6KE91CA 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 30.80 33.30 36.80 40.20 43.60 47.80 53.00 58.10 64.10 70.10 77.80 Test Current IT MIN MAX (mA) Maximum Clamping Voltage VC @ Ipp (V) 12.40 14.30 15.20 17.10 19.00 20.90 22.80 25.70 28.50 31.40 34.20 37.10 40.90 44.70 48.50 53.20 58.90 64.60 71.30 77.90 86.50 13.70 15.80 16.80 18.90 21.00 23.10 25.20 28.40 31.50 34.70 37.80 41.00 45.20 49.40 53.60 58.80 65.10 71.40 78.80 86.10 95.50 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 18.2 21.2 22.5 25.2 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 70.1 77.0 85.0 92.0 103.0 113.0 125.0 Reverse Stand off Voltage VR (Volts) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR@ VR (µA) 33.5 28.8 27.1 24.2 22.0 19.9 18.4 16.3 14.7 13.3 12.2 11.3 10.3 9.4 8.7 7.9 7.2 6.6 5.9 5.4 4.9 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts I-V Curve Characteristics Uni-directional Bi-directional Ipp Vc VBR VR IR VF IT Vc VBR VR V IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional 2 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 06/10/21 TVS Diode Datasheet TP6KE Series Axial Leaded – 600W Ratings and Characteristic Curves (TA=25°C unless otherwise noted) Figure 1 TVS Transients Clamping Waveform Figure 2 Peak Pulse Power Rating Voltage Transients 100 PPPM-Peak Pulse Power (kW) Voltage Across TVS Voltage or Current TJ initial = Tamb Current Through TVS 10 1 0.1 0.001 0.01 0.1 Figure 4 Pulse Waveform 150 100 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 Peak Pulse Power Derating Curve 75 50 25 0 25 50 75 100 125 150 175 tr=10µsec TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 200 0 TJ - Initial Junction Temperature (ºC) 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 Typical Junction Capacitance Figure 6 Typical Transient Thermal Impedance 100000 Transient Thermal Impedance ( °C/W) 100 Uni-direconal V=0V 10000 Bi-direconal V=0V Cj (pF) 10 td-Pulse Width (ms) Time 0 1 1000 100 Uni-direconal Bi-direconal V=VR 10 1 1 10 100 10 1 0.1 1000 0.01 VBR - Reverse Breakdown Voltage (V) 0.1 1 10 100 1000 TP - Pulse Duration (s) 3 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 06/10/21 TVS Diode Datasheet TP6KE Series Axial Leaded – 600W Figure 7 Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Flow/Wave Soldering (Solder Dipping) IFSM - Peak Forward Surve Current(A) 120 100 Peak Temperature : 265OC Dipping Time : 10 seconds Soldering : 1 time 80 Physical Specificationst 60 40 20 0 1 10 100 Weight 0.015oz., 0.4g Case JEDEC DO-204AC (DO-15) molded plastic body over passivated junction. Polarity Color band denotes the cathode except Bipolar. Terminal Matte Tin axial leads, solderable per JESD22-B102. Number of Cycles at 60 Hz Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 H3TRB JESD22-A101 RSH JESD22-B106 Dimensions D Cathode Band (for Uni-directional products only) Dimensions C A B A DO-204AC (DO-15) 4 Inches Min Millimeters Max Min Max A 1.000 - 25.40 - B 0.230 0.300 5.80 7.60 C 0.028 0.034 0.71 0.86 D 0.104 0.140 2.60 3.60 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 06/10/21 TVS Diode Datasheet TP6KE Series Axial Leaded – 600W Part Numbering System Part Marking System TP6KE xxx XX X Cathode Band TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) (for Uni-directional products only) F OPTION CODE: BLANK Reel Tape -B Bulk Packaging YYWW Trace Code Marking YY:Year Code WW: Week Code Littelfuse Logo VBR VOLTAGE CODE (Refer to the Electrical Characteristics table) TP6KEXXX SERIES CODE Product Type Packaging Part Number Component Package Quantity Packaging Option Packaging Specification TP6KExxxXX DO-15 (DO-204AC) 4000 Tape & Reel EIA STD RS-296 TP6KExxxXX-B DO-15 (DO-204AC) 1000 BULK Littelfuse Spec. Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.197+/-0.020 (5.0+/- 0.5) 0.236 (6.0) Dimensions are in inches/mm 13.0 (330.2) 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Direction of Feed Recess Depth Max. 0.75 (19.05) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. 5 © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: GD. 06/10/21