TPSMA6L26A

TVS Diodes Surface Mount – 600W > TPSMA6L series TPSMA6L Series RoHS Pb e3 Description Uni-directional The TPSMA6L series is designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events, and it’s especially suitable for high reliability and automotive application. SMA low profile package (DO221-AC) has the same electronical performance as the SMB package but with low height profiles (1.1mm). Agency Approvals AGENCY Features AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Peak Pulse Power Dissipation at TA=25ºC by 10x1000µs Waveform (Fig.2)(Note 1), (Note 2) Symbol Value Unit PPPM 600 W PM(AV) 3 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 60 A Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only VF 3.5V V TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead RuJL 35 °C/W Typical Thermal Resistance Junction to Ambient RuJA 200 °C/W Power Dissipation on Infinite Heat Sink at TA=50OC Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse, per Fig.4 and derated above TA=25ºC per Fig. 3. 2. Mounted on 5.0x5.0mm copper pad to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only. • Same power as standard SMB devices (600 W) • Hi reliability application and automotive grade AEC Q101 qualified • SMA low profile package: less than 1.1 mm • Footprint compatibility with standard SMA and SMB products (easy to layout) • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Low inductance, excellent clamping capability • Fast response time: typically less than 1.0ns from 0 Volts to VBR min • Built-in strain relief • Glass passivated junction • High temperature soldering: 260°C/10 seconds at terminals • Plastic package has underwriters laboratory flammability V-0 • Typical maximum temperature coefficient ΔVBR = 0.1% x VBR@25°C x ΔT • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applications Functional Diagram TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 TVS Diodes Surface Mount – 600W > TPSMA6L series Electrical Characteristics Part Number (Uni) Marking Reverse Stand off Voltage VR (Volts) TPSMA6L5.0A TPSMA6L6.0A TPSMA6L6.5A TPSMA6L7.0A TPSMA6L7.5A TPSMA6L8.0A TPSMA6L8.5A TPSMA6L9.0A TPSMA6L10A TPSMA6L11A TPSMA6L12A TPSMA6L13A TPSMA6L14A TPSMA6L15A TPSMA6L16A TPSMA6L17A TPSMA6L18A TPSMA6L20A TPSMA6L22A TPSMA6L24A TPSMA6L26A TPSMA6L28A TPSMA6L30A TPSMA6L33A TPSMA6L36A TPSMA6L40A TPSMA6L43A TPSMA6L45A TPSMA6L48A TPSMA6L51A TPSMA6L54A TPSMA6L58A TPSMA6L60A TPSMA6L64A TPSMA6L70A TPSMA6L75A TPSMA6L78A TPSMA6L85A AEA AGA AKA AMA APA ARA ATA AVA AXA AZA BEA BGA BKA BMA BPA BRA BTA BVA BXA BZA CEA CGA CKA CMA CPA CRA CTA CVA CXA CZA REA RGA RKA RMA RPA RRA RTA RVA 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approcal X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X TVS Diodes Surface Mount – 600W > TPSMA6L series I-V Curve Characteristics Uni-directional Vc VBR VR V IR VF IT Ipp PPPM VR VBR VC IR VF Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 2 - Peak Pulse Power Rating Curve Figure 1 - TVS Transients Clamping Waveform 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 Time 0.001 0.01 0.1 1 td-Pulse Width (ms.) continues on next page. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 TVS Diodes Surface Mount – 600W > TPSMA6L series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform IPPM- Peak Pulse Current, % IRSM 150 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) Cj (pF) Uni-directional V=0V Uni-directional @VR 100 10 Tj=25ºC f=1.0MHz Vsig=50mVp-p 1.0 10.0 100.0 VBR - Reverse Breakdown Voltage (V) Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 0 1.0 0 3.0 4.0 1000.0 3.6 RuJA=RuJL 3.0 2.4 1.8 1.2 RuJA=200°C/W 0.6 0 0 25 50 75 100 125 150 TA - Ambient Temperature (ºC) bargaining © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 2.0 Figure 6 - Steady State Power Dissipation Derating Curve 10000 1 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM t-Time (ms) Figure 5 - Typical Junction Capacitance 1000 tr=10µsec 175 PM(AV), Steady State Power Dissipation (W) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 175 TVS Diodes Surface Mount – 600W > TPSMA6L series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 Weight 0.002 ounce, 0.061 gram MSL JEDEC-J-STD-020, Level 1 Case JEDEC DO-221AC Molded Plastic over glass passivated junction H3TRB JESD22-A101 Polarity Color band denotes cathode except Bipolar RSH JESD22-A111 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D Dimensions Cathode Band Dimensions C B G E F E D 3.12 (0.123) Millimeters Min Max Min Max 0.156 0.181 3.950 4.600 B 0.189 0.220 4.800 5.600 C 0.049 0.069 1.250 1.750 D 0.088 0.116 2.250 2.950 E 0.030 0.059 0.750 1.500 F 0.005 0.010 0.125 0.250 G 0.035 0.043 0.900 1.100 A A Inches 1 .20 (0.047) 1.52 (0.060) Mounting Pad Layout © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 TVS Diodes Surface Mount – 600W > TPSMA6L series Part Numbering System TPSMA6L xx Part Marking System A F Cathode Band 5% VBR VOLTAGE TOLERANCE XXX VR VOLTAGE SERIES YMXXX Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Part number TPSMA6LxxA Component Package DO-221AC Packaging Option Quantity 3000 Tape & Reel – 12mm/7” tape Packaging Specification EIA RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 7.0 (178) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 Dimensions are in inches (and millimeters). Direction of Feed