TPSMA6L31A

TVS Diodes Surface Mount – 600W > TPSMA6L series TPSMA6L Series RoHS Pb e3 Description Uni-directional The TPSMA6L series is designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events, and it’s especially suitable for high reliability and automotive application. SMA low profile package (DO221-AC) has the same electronical performance as the SMB package but with low height profiles (1.1mm). Agency Approvals Agency Features Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10x1000µs Waveform (Fig.2)(Note 1), (Note 2) Parameter PPPM 600 W Power Dissipation on Infinite Heat Sink at TA=50OC PM(AV) 3 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 60 A Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only VF 3.5V V TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead R θJL 35 °C/W Typical Thermal Resistance Junction to Ambient RθJA 200 °C/W Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse, per Fig.4 and derated above TA=25ºC per Fig. 3. 2. Mounted on 5.0x5.0mm copper pad to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only. Functional Diagram • Same power as standard SMB devices (600 W) • Hi reliability application and automotive grade AEC Q101 qualified • SMA low profile package: less than 1.1 mm • Footprint compatibility with standard SMA and SMB products (easy to layout) • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) • Low inductance, excellent clamping capability • Fast response time: typically less than 1.0ns from 0 Volts to VBR min • Built-in strain relief • Glass passivated junction • High temperature soldering: 260°C/10 seconds at terminals • Plastic package has underwriters laboratory flammability V-0 • Typical maximum temperature coefficient ΔVBR = 0.1% x VBR@25°C x ΔT • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pbfree and the terminal Applications Bi-directional Cathode Anode TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Uni-directional © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.12/29/20 TVS Diodes Surface Mount – 600W > TPSMA6L series Electrical Characteristics Part Number (Uni) Marking Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT Test Current IT MIN MAX (mA) Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) Agency Approval TPSMA6L5.0A AEA 5.0 6.40 7.00 10 9.2 65.3 800 X TPSMA6L6.0A AGA 6.0 6.67 7.37 10 10.3 58.3 800 X TPSMA6L6.5A AKA 6.5 7.22 7.98 10 11.2 53.6 500 X TPSMA6L7.0A AMA 7.0 7.78 8.60 10 12.0 50.0 200 X TPSMA6L7.5A APA 7.5 8.33 9.21 1 12.9 46.6 100 X TPSMA6L8.0A ARA 8.0 8.89 9.83 1 13.6 44.2 50 X TPSMA6L8.5A ATA 8.5 9.44 10.40 1 14.4 41.7 20 X TPSMA6L9.0A AVA 9.0 10.00 11.10 1 15.4 39.0 10 X TPSMA6L10A AXA 10.0 11.10 12.30 1 17.0 35.3 5 X TPSMA6L11A AZA 11.0 12.20 13.50 1 18.2 33.0 1 X TPSMA6L12A BEA 12.0 13.30 14.70 1 19.9 30.2 1 X TPSMA6L13A BGA 13.0 14.40 15.90 1 21.5 28.0 1 X TPSMA6L14A BKA 14.0 15.60 17.20 1 23.2 25.9 1 X TPSMA6L15A BMA 15.0 16.70 18.50 1 24.4 24.6 1 X TPSMA6L16A BPA 16.0 17.80 19.70 1 26.0 23.1 1 X TPSMA6L17A BRA 17.0 18.90 20.90 1 27.6 21.8 1 X TPSMA6L18A BTA 18.0 20.00 22.10 1 29.2 20.6 1 X TPSMA6L20A BVA 20.0 22.20 24.50 1 32.4 18.6 1 X TPSMA6L22A BXA 22.0 24.40 26.90 1 35.5 16.9 1 X TPSMA6L24A BZA 24.0 26.70 29.50 1 38.9 15.5 1 X TPSMA6L26A CEA 26.0 28.90 31.90 1 42.1 14.3 1 X TPSMA6L28A CGA 28.0 31.10 34.40 1 45.4 13.3 1 X TPSMA6L30A CKA 30.0 33.30 36.80 1 48.4 12.4 1 X TPSMA6L33A CMA 33.0 36.70 40.60 1 53.3 11.3 1 X TPSMA6L36A CPA 36.0 40.00 44.20 1 58.1 10.4 1 X TPSMA6L40A CRA 40.0 44.40 49.10 1 64.5 9.3 1 X TPSMA6L43A CTA 43.0 47.80 52.80 1 69.4 8.7 1 X TPSMA6L45A CVA 45.0 50.00 55.30 1 72.7 8.3 1 X TPSMA6L48A CXA 48.0 53.30 58.90 1 77.4 7.8 1 X TPSMA6L51A CZA 51.0 56.70 62.70 1 82.4 7.3 1 X TPSMA6L54A REA 54.0 60.00 66.30 1 87.1 6.9 1 X TPSMA6L58A RGA 58.0 64.40 71.20 1 93.6 6.5 1 X TPSMA6L60A RKA 60.0 66.70 73.70 1 96.8 6.2 1 X TPSMA6L64A RMA 64.0 71.10 78.60 1 103.0 5.9 1 X TPSMA6L70A RPA 70.0 77.80 86.00 1 113.0 5.3 1 X TPSMA6L75A RRA 75.0 83.30 92.10 1 121.0 5.0 1 X TPSMA6L78A RTA 78.0 86.70 95.80 1 126.0 4.8 1 X TPSMA6L85A RVA 85.0 94.40 104.00 1 137.0 4.4 1 X © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.12/29/20 TVS Diodes Surface Mount – 600W > TPSMA6L series I-V Curve Characteristics Uni-directional Vc VBR VR V IR VF IT Ipp PPPM Peak Pulse Power Dissipation - Max power dissipation VR Stand-off Voltage - Maximum voltage that can be applied to the TVS without operation VBR Breakdown Voltage - Maximum voltage that flows though the TVS at a specified test current (IT) VC Clamping Voltage - Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) IR Reverse Leakage Current - Current measured at VR VF Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 Time 0.001 0.01 0.1 1 td-Pulse Width (ms.) continues on next page. © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.12/29/20 TVS Diodes Surface Mount – 600W > TPSMA6L series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 tr=10µsec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 0 175 Uni-directional @VR 100 10 Tj=25ºC f=1.0MHz Vsig=50mVp-p 100.0 VBR - Reverse Breakdown Voltage (V) 1000.0 PM(AV), Steady State Power Dissipation (W) Cj (pF) Uni-directional V=0V 10.0 3.0 4.0 Figure 6 - Steady State Power Dissipation Derating Curve 10000 1.0 2.0 t-Time (ms) Figure 5 - Typical Junction Capacitance 1 1.0 0 TJ-Initial Junction Temperature (ºC) 1000 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 3.6 RθJA=RθJL 3.0 2.4 1.8 1.2 RθJA=200°C/W 0.6 0 0 25 50 75 100 125 150 TA - Ambient Temperature (ºC) 175 bargaining © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.12/29/20 TVS Diodes Surface Mount – 600W > TPSMA6L series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (tL) 60 – 150 seconds Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) 30 seconds max Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes max. Do not exceed 280°C +0/-5 tp TP Ramp-up TL Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat °C Physical Specifications 25˚C t 25˚C to Peak Time (t) Environmental Specifications Weight 0.002 ounce, 0.061 gram Temperature Cycle JESD22-A104 Case JEDEC DO-221AC Molded Plastic over glass passivated junction Pressure Cooker JESD22-A102 Polarity Color band denotes cathode except Bipolar High Temp. Storage JESD22-A103 Matte Tin-plated leads, Solderable per JESD22-B102D HTRB JESD22-A108 Thermal Shock JESD22-A106 Terminal Critical Zone TL to TP Dimensions Cathode Band Dimensions C B G E F E D 3.12 (0.123) Millimeters Min Max Min Max 0.156 0.181 3.950 4.600 B 0.189 0.220 4.800 5.600 C 0.049 0.069 1.250 1.750 D 0.088 0.116 2.250 2.950 E 0.030 0.059 0.750 1.500 F 0.005 0.010 0.125 0.250 G 0.035 0.043 0.900 1.100 A A Inches 1 .20 (0.047) 1.52 (0.060) Mounting Pad Layout © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.12/29/20 TVS Diodes Surface Mount – 600W > TPSMA6L series Part Numbering System TPSMA6L xx Part Marking System A F Cathode Band 5% VBR VOLTAGE TOLERANCE XXX VR VOLTAGE SERIES YMXXX Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Part number Component Package TPSMA6LxxA DO-221AC Packaging Option Quantity 3000 Tape & Reel – 12mm/7” tape Packaging Specification EIA RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape 7.0 (178) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics © 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: JC.12/29/20