TPSMC39CA

TVS Diodes Surface Mount – 1500W > TPSMC series TPSMC Series RoHS Pb e3 Description The TPSMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 1500 W Power Dissipation on Infinite Heat Sink at TA=50OC PM(AV) 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 200 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only VF 3.5 V TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Features • Hi reliability application and automotive grade AEC-Q101 qualified • For surface mounted applications to optimize board space • Low profile package. • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • VBR @TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient) • Glass passivated chip junction • 1500W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0V to VBR min • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 1µA above 13V • High temperature soldering guaranteed: 260°C/10 seconds at terminals • UL Recognized body that meets flammability rating V-0. • Meet MSL level1, per J-STD-020, high temperature soldering guaranteed. • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • UL Recognized to ANSI/ UL 497B: Protectors for Data Communications and Fire-Alarm Circuits. Applications TVS Components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 TVS Diodes Surface Mount – 1500W > TPSMC series Electrical Characteristics Part Number (Uni) Part Number (Bi) Marking UNI BI Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) Agency Approval TPSMC12A TPSMC12CA 12AA 12CA 10.20 11.40 12.60 1 16.7 91.0 5 X TPSMC13A TPSMC13CA 13AA 13CA 11.10 12.40 13.70 1 18.2 83.5 1 X TPSMC15A TPSMC15CA 15AA 15CA 12.80 14.30 15.80 1 21.2 71.7 1 X TPSMC16A TPSMC16CA 16AA 16CA 13.60 15.20 16.80 1 22.5 67.6 1 X TPSMC18A TPSMC18CA 18AA 18CA 15.30 17.10 18.90 1 25.2 60.3 1 X TPSMC20A TPSMC20CA 20AA 20CA 17.10 19.00 21.00 1 27.7 54.9 1 X TPSMC22A TPSMC22CA 22AA 22CA 18.80 20.90 23.10 1 30.6 49.7 1 X TPSMC24A TPSMC24CA 24AA 24CA 20.50 22.80 25.20 1 33.2 45.8 1 X TPSMC27A TPSMC27CA 27AA 27CA 23.10 25.70 28.40 1 37.5 40.5 1 X TPSMC30A TPSMC30CA 30AA 30CA 25.60 28.50 31.50 1 41.4 36.7 1 X TPSMC33A TPSMC33CA 33AA 33CA 28.20 31.40 34.70 1 45.7 33.3 1 X TPSMC36A TPSMC36CA 36AA 36CA 30.80 34.20 37.80 1 49.9 30.5 1 X TPSMC39A TPSMC39CA 39AA 39CA 33.30 37.10 41.00 1 53.9 28.2 1 X TPSMC43A TPSMC43CA 43AA 43CA 36.80 40.90 45.20 1 59.3 25.6 1 X TPSMC47A TPSMC47CA 47AA 47CA 40.20 44.70 49.40 1 64.8 23.5 1 X TPSMC51A TPSMC51CA 51AA 51CA 43.60 48.50 53.60 1 70.1 21.7 1 X TPSMC56A TPSMC56CA 56AA 56CA 47.80 53.20 58.80 1 77.0 19.7 1 X TPSMC62A TPSMC62CA 62AA 62CA 53.00 58.90 65.10 1 85.0 17.9 1 X TPSMC68A TPSMC68CA 68AA 68CA 58.10 64.60 71.40 1 92.0 16.5 1 X TPSMC75A TPSMC75CA 75AA 75CA 64.10 71.30 78.80 1 103.0 14.8 1 X TPSMC82A TPSMC82CA 82AA 82CA 70.10 77.90 86.10 1 113.0 13.5 1 X TPSMC91A TPSMC91CA 91AA 91CA 77.80 86.50 95.50 1 125.0 12.2 1 X TPSMC100A - 100AA - 85.50 95.00 105.00 1 137.0 11.1 1 X For bidirectional type having VR of 10 volts and less, the IR limit is double. I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT V Vc VBR VR Ipp PPPM VR VBR VC IR VF IT IR IR IT VR VBR Vc V Ipp Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 TVS Diodes Surface Mount – 1500W > TPSMC series Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 0.31x0.31" (8.0x8.0mm) Copper Pad Area 1 0.000001 0.00001 Time Figure 3 - Peak Pulse Power Derating Curve 80 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 150 TPSMC91A~TPSMC100A 60 40 TPSMC91A~TPSMC100A TPSMC12CA~TPSMC91CA 20 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (ºC) tr=10µsec Uni-directional @VR 100 Bi-directional @VR 10 1 1.0 Tj=25C f=1.0MHz Vsig=50mVp-p 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) 2 50 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 Figure 6 - Steady State Power Dissipation Derating Curve PM(AV), Steady Sate Power Dissipation (W) 1000 ( ) t-Time (ms) Bi-directional V=0V Uni-directional V=0V Half Value IPPM IPPM 0 100000 10000 TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 175 Figure 5 - Typical Junction Capacitance Cj (pF) 0.001 Figure 4 - Pulse Waveform 100 0 0.0001 td-Pulse Width (sec.) 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 150 175 TA - Ambient Temperature (ºC) © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 TVS Diodes Surface Mount – 1500W > TPSMC series Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) 200 180 160 140 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) - Time (min to max) (ts) 217°C 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 30 seconds max Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes max. Do not exceed 260°C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition Critical Zone TL to TP tL Ts(max) Ts(min) Ramp-down ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications Weight 0.007 ounce, 0.21 grams High Temp. Storage JESD22-A103 Case JEDEC DO214AB. Molded plastic body over glass passivated junction HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22--A111 Polarity Color band denotes positive end (cathode) except Bidirectional. Terminal Matte Tin-plated leads, Solderable per JESD22-B102 © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 TVS Diodes Surface Mount – 1500W > TPSMC series Dimensions DO-214AB (SMC J-Bend) Cathode Band (for Uni-directional products only) Dimensions A C A B H D F E G L K J I Inches Millimeters Min Max Min Max 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 2.620 D 0.079 0.103 2.060 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - Solder Pads (all dimensions in mm) Part Numbering System Part Marking System TPSMC XXX C A 5% VBR VOLTAGE TOLERANCE F Cathode Band Littelfuse Logo XXXX Marking Code YMXXX BI-DIRECTIONAL Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code VBR VOLTAGE SERIES Packaging Part number TPSMCxxxXX Component Package DO-214AB Quantity 3000 Packaging Option Packaging Specification Tape & Reel - 16mm tape/13” reel EIA STD RS-481 © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 TVS Diodes Surface Mount – 1500W > TPSMC series Tape and Reel Specification 0.157 (4.0) Cathode 0.63 (16.0) 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. © 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19