HANBit
HMF2M32F4VSA
Flash-ROM Module 8MByte (2Mx32Bit), 80Pin-MMC, 3.3V Design Part No. HMF2M32F4VSA
GENERAL DESCRIPTION
The HMF2M32F4V is a high-speed flash read only memory (FROM) module containing 2,097,152 words organized in a x32bit configuration. The module consists of four 1M x 16 FROM mounted on a 80-pin stackable type, double - sided, FR4printed circuit board. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine, which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from 12.0V flash or EPROM devices. Output enable (/OE) and write enable (/WE) can set the memory input and output. The host system can detect a program or erase operation is complete by observing the Ready Pin, or reading the DQ7(Data # Polling) and DQ6(Toggle) status bits. When FROM module is disable condition the module is becoming power standby mode, system designer can g et low-power design. All module components may be powered from a single + 3.0V DC power supply and all inputs and outputs are LVTTLcompatible.
FEATURES
P1
PIN ASSIGNMENT
P2 Symbol VCC DQ16 DQ24 DQ17 DQ25 DQ18 VSS DQ26 DQ19 DQ27 DQ20 DQ28 DQ21 VSS DQ29 DQ22 DQ30 DQ23 DQ31 VCC PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VCC DQ15 DQ7 DQ14 DQ6 DQ13 VSS DQ5 DQ12 DQ4 DQ11 DQ3 DQ10 VSS DQ2 DQ9 DQ1 DQ8 DQ0 VCC PIN 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Symbol VCC NC NC BYTE* OE* CE1* VSS A13 A29 A11 A12 A22 A23 VSS A24 A25 A26 A27 A28 VCC
w Part Identification
- HMF2M32F4VSA : Socket 5mm w Access time: 70, 80, 90, 120ns w High-density 8MByte design w High-reliability, low-power design w Single + 3.0V ± 0.5V power supply w All in/outputs are LVTTL-compatible w FR4-PCB design w 80-pin Designed by 40-pin Fine Pitch Connector (x 2EA) w Minimum 1,000,000 write/erase cycle w Sector erases architecture
PIN 1 2 3 4 5 6 7 8 9 10 11 12
Symbol VCC CE0* NC NC NC RY_BY* VSS RESET* W E* A10 A21 A20 A19 VSS A18 A17 A16 A15 A14 VCC
PIN 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
OPTIONS
w Timing 70ns access 80ns access 90ns access 120ns access w Packages 80-pin MMC
MARKING
-70 -80 -90 -120
13 14 15 16 17 18 19 20
F
4 cf : Address & Data Bus is organized for LG Specification. ( A10 & DQ0 are MSB, A29 & DQ31 a re LSB)
URL: www.hbe.co.kr REV.02(August,2002)
1
HANBit Electronics Co., Ltd.
HANBit
FUNCTIONAL BLOCK DIAGRAM
HMF2M32F4VSA
32 DQ0 - DQ31 20 A10 – A29 A10-29 DQ16-31 /WE /OE /CE RY-BY /Reset
U1
A10-29 DQ 0-15 /WE /OE /CE0 /CE RY-BY /Reset
U2
A10-29 DQ16-31
/WE /OE /CE
RY-BY /Reset
U3
A10-29 DQ 0-15
/WE
/OE /CE1 RY_/BY /Reset
/WE /OE /CE RY-BY /Reset
U4
URL: www.hbe.co.kr REV.02(August,2002)
2
HANBit Electronics Co., Ltd.
HANBit
TRUTH TABLE
MODE STANDBY NOT SELECTED READ W RITE or ERASE NOTE: X means don’t care /OE X H L X /CE H L L L /WE X H H L /RESET Vcc±0.3V H H H
HMF2M32F4VSA
DQ ( /BYTE=L ) HIGH-Z HIGH-Z DOUT DIN
POWER STANDBY ACTIVE ACTIVE ACTIVE
ABSOLUTE MAXIMUM RATINGS
PARAMETER Voltage with respect to ground all other pins Voltage with respect to ground Vcc Storage Temperature SYMBOL VIN,OUT VCC TSTG RATING -0.5V to Vcc+0.5V -0.5V to +4.0V -65oC to +150oC
Operating Temperature TA -55oC to +125 oC w Stresses greater than those listed under " Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
PARAMETER Vcc for ± 10% device Supply Voltages Ground SYMBOL Vcc VSS MIN 2.7V 0 0 TYP. MAX 3.6V 0
DC AND OPERATING CHARACTERISTICS ( 0oC ≤ TA ≤ 70 oC )
PARAMETER Input Load Current Output Leakage Current Output High Voltage Output Low Voltage Vcc Active Read Current (1) /OE = VIH, Vcc Active Write Current (2) Vcc Standby Current Low Vcc Lock-Out Voltage Notes : 1. The Icc current listed is typically less than 2mA/MHz, with /OE at V IH. 2. Icc active while embedded algorithm (program or erase) is in progress 3. Maximum Icc current specifications are tested with Vcc=Vcc max /CE = VIL, /OE=VIH /CE, /RESET=Vcc ±0.3V 1MHZ ICC2 ICC3 VLKO 2.3 TEST CONDITIONS Vcc=Vcc max, V IN= GND to Vcc Vcc=Vcc max, V OUT= GND to Vcc IOH = -2.0mA, Vcc = Vcc min IOL = 4.0mA, Vcc =Vcc min /CE = VIL, 5MHZ ICC1 4 40 8 60 60 2.5 mA mA V SYMBOL IL1 IL0 VOH VOL 18 2.4 0.45 32 mA MIN MAX ±1.0 ±1.0 UNIT µA µA V V
URL: www.hbe.co.kr REV.02(August,2002)
3
HANBit Electronics Co., Ltd.
HANBit
ERASE AND PROGRAMMING PERFORMANCE
LIMITS PARAMETER MIN. Sector Erase Time Chip Erase Time Byte Programming Time Chip Programming Time TYP. 0.7 25 9 18 300 54 MAX. 15 sec sec µs sec UNIT
HMF2M32F4VSA
COMMENTS
Excludes 00H programming prior to erasure Excludes system-level overhead
TSOP CAPACITANCE
PARAMETER SYMBOL CIN COUT CIN2 PARAMETER DESCRIPTION Input Capacitance Output Capacitance Control Pin Capacitance TEST SETUP VIN = 0 VOUT = 0 VIN = 0 MIN 6 8.5 7.5 MAX 7.5 12 9 UNIT pF pF pF
Notes : Test conditions TA = 25o C, f=1.0 MHz.
AC CHARACTERISTICS u Read Only Operations Characteristics
PARAMETER SYMBOLS DESCRIPTION JEDEC STANDARD tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX tRC tACC tCE tOE tDF tDF tQH Read Cycle Time Address to Output Delay Chip Enable to Output Delay Chip Enable to Output Delay Chip Enable to Output High-Z Output Enable to Output High-Z Output Hold Time From Addresses, /CE or /OE, Whichever Occurs First /CE = V IL /OE = VIL /OE = VIL Min Max Max Max Max Max Min TEST SETUP -70R 70 70 70 30 25 25 -80 80 80 80 30 25 25 0 -90 90 90 90 35 30 30 -120 120 120 120 35 30 30 ns ns ns ns ns ns ns Speed Options UNIT
TEST SPECIFICATIONS
TEST CONDITION Output load Output load capacitance,CL (Including jig capacitance) Input rise and full times Input pulse levels Input timing measurement reference levels Output timing measurement reference levels 30 5 0.0-3.0 1.5 1.5 70R, 80 1TTL gate 100 pF ns V V V 90, 120 UNIT
URL: www.hbe.co.kr REV.02(August,2002)
4
HANBit Electronics Co., Ltd.
HANBit
5.0V
HMF2M32F4VSA
2.7kΩ Device Under Test CL IN3064 or Equivalent
6.2kΩ
Diodes = IN3064 or Equivalent
Note : CL = 100pF including jig capacitance
u Erase/Program Operations
PARAMETER SYMBOLS DESCRIPTION JEDEC tAVAV tAVWL tWLAX tDVWH tWHDX STANDARD tWC tAS tAH tDS tDH tOES tGHWL tELWL tWHEH tWLWH tWHWL tWHWH1 tWHWH2 tGHWL tCS tCH tWP tWPH tWHWH1 tWHWH2 tVCS W rite Cycle Time Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Read Recover Time Before Write /CE Setup Time /CE Hold Time W rite Pulse Width W rite Pulse Width High Byte Programming Operation Sector Erase Operation (Note1) Vcc set up time Min Min Min Min Min Min Min Min Min Min Min Typ Typ Min 35 35 30 9 0.7 50 45 35 45 35 0 0 0 0 0 35 50 70R 70 80 80 0 45 45 50 50 90 90 120 12 ns ns ns ns ns ns ns ns ns ns ns µs sec µs Speed Options UNIT
Notes : 1 . This does not include the preprogramming time 2 . This timing is only for Sector Protect operations
URL: www.hbe.co.kr REV.02(August,2002)
5
HANBit Electronics Co., Ltd.
HANBit
u Erase/Program Operations Alternate /CE Controlled Writes
PARAMETER SYMBOLS DESCRIPTION JEDEC tAVAV tAVWL tWLAX tDVWH tWHDX STANDARD tWC tAS tAH tDS tDH tOES tGHWL tELWL tWHEH tWLWH tWHWL tWHWH1 tWHWH2 tGHWL tCS tCH tWP tWPH tWHWH1 tWHWH2 W rite Cycle Time Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Read Recover Time Before Write /CE Setup Time /CE Hold Time W rite Pulse Width W rite Pulse Width High Byte Programming Operation Sector Erase Operation (Note1) Min Min Min Min Min Min Min Min Min Min Min Typ Typ 35 35 45 35 45 35 -70R 70 -80 80
HMF2M32F4VSA
Speed Options UNIT -90 90 0 45 45 0 0 0 0 0 35 30 9 0.7 50 50 50 120 12 ns ns ns ns ns ns ns ns ns ns ns µs sec
Notes : 1. This does not include the preprogramming time 2 . This timing is only for Sector Protect operations
URL: www.hbe.co.kr REV.02(August,2002)
6
HANBit Electronics Co., Ltd.
HANBit
u READ OPERATIONS TIMING
HMF2M32F4VSA
u RESET TIMING
URL: www.hbe.co.kr REV.02(August,2002)
7
HANBit Electronics Co., Ltd.
HANBit
u PROGRAM OPERATIONS TIMING
HMF2M32F4VSA
u CHIP/SECTOR ERASE OPERATION TIMINGS
URL: www.hbe.co.kr REV.02(August,2002)
8
HANBit Electronics Co., Ltd.
HANBit
u DATA# POLLING TIMES(DURING EMBEDDED ALGORITHMS)
HMF2M32F4VSA
u TOGGLE# BIT TIMINGS (DURING EMBEDDED ALGORITHMS)
URL: www.hbe.co.kr REV.02(August,2002)
9
HANBit Electronics Co., Ltd.
HANBit
u SECTOR PROTECT UNPROTECT TIMEING DIAGRAM
HMF2M32F4VSA
u ALTERNATE CE# CONTROLLED WRITE OPERATING TIMINGS
URL: www.hbe.co.kr REV.02(August,2002)
10
HANBit Electronics Co., Ltd.
HANBit
PACKAGE DIMMENSIONS
HMF2M32F4VSA
URL: www.hbe.co.kr REV.02(August,2002)
11
HANBit Electronics Co., Ltd.
HANBit
ORDERING INFORMATION
Component Number 2EA 2EA 2EA 2EA
HMF2M32F4VSA
Part Number
Density
Org.
Package
Vcc
SPEED
HMF2M32F2V-70 HMF2M32F2V-80 HMF2M32F2V-90 HMF2M32F2V-120
4MByte 4Mbyte 4Mbyte 4Mbyte
x 32
80Pin -MMC 80Pin – MMC 80Pin – MMC 80Pin -MMC
3.3V 3.3V 3.3V 3.3V
70ns 80ns 90ns 120ns
x 32 x 32 x 32
URL: www.hbe.co.kr REV.02(August,2002)
12
HANBit Electronics Co., Ltd.