FH39J-51S-0.3SHW

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. NEW 0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors FH39 Series qSmall size (39 pos. shown) 1.1mm 13.9 mm (39 pos .) 3. 45 m m sFeatures 1. Low-profile 0.3mm pitch connector with top and bottom contact Usable via either its top or bottom contact point, this connector achieves enhanced freedom in terms of the product design. qEasy FPC insertion actuator 2. High contact reliability thanks to the spring terminal structure Because both top and bottom contact points are springloaded, the contact point adapts to the FPC motion, and high contact reliability is ensured. FPC 3. Delivered with the actuator open FPC can be immediately inserted without the need for the opening of the actuator. qCompletely locked 4. Easy FPC insertion Entry chamfers at all sides of the FPC insertion slot assure correct insertion and positioning of the FPC. 5. Accepts standard FPC thickness 0.2mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 6. Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 7. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5000 connectors. 8. Halogen-free* (FH39J Series) *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 2010.9 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sSpecifications Current rating 0.2 A Ratings Voltage rating 30 Vrms AC Recommended FPC Operating -55 to +85°C (Note 1) temperature range Operating Relative humidity 90% max. humidity range (No condensation) Storage -10 to +50°C (Note 2) temperature range Storage Relative humidity 90% max. humidity range (No condensation) Thickness: 0.2 ± 0.03 mm, Gold plated contact pads Conditions 100 V DC 90 Vrms AC / 1 minute 1 mA, AC max (AC: 1kHz) 10 cycles Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycles in each of the 3 axis Acceleration of 981m/s2, 6 ms duration, sine half-wave, 3 cycles in each of the 3 axis 96 hours at 40ç and humidity of 90 to 95% Temperature:-55ç➝+15ç to +35ç➝+85ç➝+15ç to +35ç Time: 30➝ 2 to 3 ➝ 30➝ 2 to 3 minutes 5 cycles Reflow: At the recommended temperature profile Manual soldering: 350ç ± 5ç for 5 seconds Item Specification 1.Insulation resistance 50 Mø min. 2.Withstanding voltage No flashover or insulation breakdown 100 mø max. 3.Contact resistance * Including FPC and FFC conductor resistance Contact resistance: 100 mø max. 4.Durability No damage, cracks, or parts dislocation No electrical discontinuity of 1µs or longer 5.Vibration Contact resistance: 100 mø max. No damage, cracks, or parts dislocation No electrical discontinuity of 1µs or longer 6.Shock Contact resistance: 100 mø max. No damage, cracks, or parts dislocation Contact resistance: 100 mø max. 7.Humidity Insulation resistance: 50 Mø min. (Steady state) No damage, cracks, or parts dislocation Contact resistance: 100 mø max. 8.Temperature cycle Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation 9.Resistance to No deformation of components affecting soldering heat performance Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. sMaterials Part Insulator Contacts Metalfittings Material LCP PA Phosphor bronze Finish Color:Beige Color:Black Gold plated Pure tin reflow plated Remarks UL94V-0 --------------------------------- sOrdering information FH 39 J - 51S - 0.3 SHW (10) 1 2 3 4 5 6 7 1 Series name:FH 2 Series No.:39 3 Blank :Standard A :Long actuator type J :Halogen-free requirements (Flame retardance UL94V-0). 4 Number of positions FH39 :25 to 61 FH39A :67, (71 under planning) FH39J :25 to 51 5 Contact pitch:0.3mm 6 Termination type SHW...SMT horizontal staggered row mount type 7 Plating specifications (10)...Gold plating with nickel barrier 2 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sConnector Dimensions A±0.15 0.3±0.1 0.6±0.1 B±0.1 (0.12) Production LOT No. 0.6±0.1 C±0.1 B (0.12) (0.15) (D) E±0.1 (0.6) (3.3) B Detailed drawing [FH39 Series] (0.42) (FPC:t0.2mm) (0.42) (FPC:t0.2mm) (3.85) (2.1) (1.55) (0.85) B Detailed drawing [FH39A Series] (4.15) (2.1) (1.55) (0.85) (9 0˚ (1.85) 3.55±0.2 1.1±0.1 (1.89) 1.1±0.1 (1.54) ˚) (90 0.3±0.1 0.1±0.15 1 ) 0.47±0.1 0.1±0.15 1 3.25±0.15 0.1 0.47±0.1 0.1±0.15 1 3.25±0.15 1 0.3±0.1 0.1±0.15 0.1 0.1 0.1 Note 1 2 3 4 : : : : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. Packaged on tape and reel only. Check packaging specification. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. After reflow, the terminal plating may change color, however this does not represent a quality issue. All dimensions: mm D E 7.83 9.15 8.43 9.75 9.03 10.35 10.23 11.55 12.03 13.35 13.83 15.15 15.63 16.95 18.63 19.95 20.43 21.75 21.63 22.95 7.83 9.15 10.23 11.55 12.03 13.35 13.83 15.15 15.63 16.95 Part Number FH39-25S-0.3SHW(10) FH39-27S-0.3SHW(10) FH39-29S-0.3SHW(10) FH39-33S-0.3SHW(10) FH39-39S-0.3SHW(10) FH39-45S-0.3SHW(10) FH39-51S-0.3SHW(10) FH39-61S-0.3SHW(10) FH39A-67S-0.3SHW(10) FH39A-71S-0.3SHW(10) FH39J-25S-0.3SHW(10) FH39J-33S-0.3SHW(10) FH39J-39S-0.3SHW(10) FH39J-45S-0.3SHW(10) FH39J-51S-0.3SHW(10) CL No. 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 Under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 Number of contacts 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 A 9.7 10.3 10.9 12.1 13.9 15.7 17.5 20.5 22.3 23.5 9.7 12.1 13.9 15.7 17.5 B 6.6 7.2 7.8 9 10.8 12.6 14.4 17.4 19.2 20.4 6.6 9 10.8 12.6 14.4 C 7.2 7.8 8.4 9.6 11.4 13.2 15 18 19.8 21 7.2 9.6 11.4 13.2 15 Tape and reel packaging (5,000 pieces/reel). Order by number of reels. 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sRecommended PCB mounting pattern and metal mask dimensions (Metal mask:0.42) B±0.05 0.5±0.05 Recommended metal mask thickness : t=0.1 0.6±0.05 (0.1) (0.2) 0.2±0.03 3.65MIN (Stiffner) 0.1±0.05 (Metal mask:1) 1±0.05 0.35±0.05 (Metal mask:0.35) 0.8±0.05 1.05±0.1 1.15±0.1 (Uncovered area) 2.25±0.1 2.1±0.1 2.65±0.3 0.3±0.03 (Metal mask:0.25) 2.48±0.05 (3.65) 0.3±0.05 (Metal mask:0.57) 0.67±0.05 0.3±0.03 (Metal mask:0.25) C±0.05 0.6±0.05 sRecommended FPC Dimensions F±0.05 0.3±0.07 0.3 +0.04 -0.03 C±0.03 0.3±0.07 0.6±0.02 0.3±0.02 0.3±0.1 2- R0 .2 0.3 +0.04 -0.03 0.1 0.2 0.1±0.02 0.6±0.07 B±0.03 0.6±0.07 * Stiffener dimension should be 3.65mm min., and X dimension should be 0.5mm for improved flexibility of FPC. All dimensions: mm F 7.8 8.4 9 10.2 12 13.8 15.6 18.6 20.4 21.6 7.8 10.2 12 13.8 15.6 Part Number FH39-25S-0.3SHW(10) FH39-27S-0.3SHW(10) FH39-29S-0.3SHW(10) FH39-33S-0.3SHW(10) FH39-39S-0.3SHW(10) FH39-45S-0.3SHW(10) FH39-51S-0.3SHW(10) FH39-61S-0.3SHW(10) FH39A-67S-0.3SHW(10) FH39A-71S-0.3SHW(10) FH39J-25S-0.3SHW(10) FH39J-33S-0.3SHW(10) FH39J-39S-0.3SHW(10) FH39J-45S-0.3SHW(10) FH39J-51S-0.3SHW(10) CL No. 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 Under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 Number of contacts 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 B 6.6 7.2 7.8 9 10.8 12.6 14.4 17.4 19.2 20.4 6.6 9 10.8 12.6 14.4 C 7.2 7.8 8.4 9.6 11.4 13.2 15 18 19.8 21 7.2 9.6 11.4 13.2 15 4 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sRecommended FPC construction 1. Using Single-sided FPC FPC : Flexible Printed Circuit Material Name Covering film layer Cover adhesive Surface treatment Copper foil Base adhesive Base film Stiffener Polyimide Material 1 mil thick. Material Thickness (µm) (25) (25) 3 35 25 25 40 75 203 1 mil thick 3 mil thick 0.2µm thick gold plated over 1 to 5µm nickel underplating Cu 1oz Thermosetting adhesive Polyimide Polyimide Total Reinforcement material adhesive Thermosetting adhesive 2. Using Double-sided FPC FPC : Flexible Printed Circuit Material Name Covering film layer Cover adhesive Surface treatment Through-hole copper Copper foil Base adhesive Base film Base adhesive Copper foil Cover adhesive Covering film layer Stiffener 0.2µm thick gold plated over 1 to 5µm nickel underplating Material Polyimide 1 mil thick. Material Thickness (µm) (25) (25) 3 15 18 18 25 18 (18) 25 25 25 25 197 Cu Cu 1/2oz Thermosetting adhesive Polyimide Cu 1/2oz Thermosetting adhesive Polyimide Polyimide Total 1 mil thick. 3 mil thick 1 mil thick Thermosetting adhesive Reinforcement material adhesive Thermosetting adhesive * To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT RECOMMENDED. 3. Precautions 1: This specification is a recommendation for the construction of the FH39 Series FPC (t=0.2±0.05). 2: For details about the construction, please contact the FPC manufacturers. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sPackaging Specification qEmbossed Carrier Tape Dimensions (Tape width to 24mm max.) .1 +0 0 (0.3) Ø 1.5 J±0.1 1.75±0.1 (2.1:FH39 series) (2.4:FH39A series) 4±0.1 2±0.15 8±0.1 Flat surface, for placement with automatic equipment. (4.65) Unreeling direction (1.85) qEmbossed Carrier Tape Dimensions (Tape width 32mm min.) Ø 1.5 .1 +0 0 (K) J±0.1 1.75±0.1 H±0.1 1.7 +0.15 0 1.5 +0.1 0 qReel Dimensions 3) (Ø1 (L: INSIDE) (Ø380) (Ø80) (M: OUTSIDE) 6 G±0.3 G±0.3 (K) The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Part Number FH39-25S-0.3SHW(10) FH39-27S-0.3SHW(10) FH39-29S-0.3SHW(10) FH39-33S-0.3SHW(10) FH39-39S-0.3SHW(10) FH39-45S-0.3SHW(10) FH39-51S-0.3SHW(10) FH39-61S-0.3SHW(10) FH39A-67S-0.3SHW(10) FH39A-71S-0.3SHW(10) FH39J-25S-0.3SHW(10) FH39J-33S-0.3SHW(10) FH39J-39S-0.3SHW(10) FH39J-45S-0.3SHW(10) FH39J-51S-0.3SHW(10) CL No. 580-1806-8-10 580-1805-5-10 580-1807-0-10 580-1803-0-10 580-1800-1-10 580-1802-7-10 580-1801-4-10 580-1808-3-10 580-1809-6-10 Under planning 580-1815-9-10 580-1814-6-10 580-1813-3-10 580-1811-8-10 580-1812-0-10 Number of contacts 25 27 29 33 39 45 51 61 67 71 25 33 39 45 51 G 24 24 24 24 24 32 32 44 44 44 24 24 24 32 32 H ----------28.4 28.4 40.4 40.4 40.4 ------28.4 28.4 J 11.5 11.5 11.5 11.5 11.5 14.2 14.2 20.2 20.2 20.2 11.5 11.5 11.5 14.2 14.2 K 11 11.6 12.2 13.4 15.2 17 18.8 21.8 23.6 24.8 11 13.4 15.2 17 18.8 All dimensions: mm L M 25.4 25.4 25.4 25.4 25.4 33.4 33.4 45.4 45.4 45.4 25.4 25.4 25.4 33.4 33.4 29.4 29.4 29.4 29.4 29.4 37.4 37.4 49.4 49.4 49.4 29.4 29.4 29.4 37.4 37.4 Tape and reel packaging (5,000 pieces/reel). 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sTemperature Profile MAX 250ç 250 230ç 200 200ç (ç) Temperature 150 150ç HRS test condition Solder method :Reflow, IR/hot air Environment :Room air Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part Number:M705-221CM5-32-10.5) Test board :Glass epoxy 25mm∞50mm∞0.8mm thick Land dimensions :0.3mm∞0.5mm, 0.3mm∞0.67mm Metal mask :0.25∞0.42, 0.25∞0.57∞0.1mm thick The temperature profiles shown are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations. 100 50 25ç (60sec.) 90 sec. to 120 sec. 0 Start Time (Seconds) Preheating (60sec.) Soldering 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors sConnector Operation and Precautions Operation Exercise care when handling connectors. Follow recommendations given below. 1. As delivered Delivered with the actuator open. There is no need to operate the actuator prior to the insertion of the FPC. The actuator is open when delivered in the embossed tape packaging 2. FPC insertion Align the FPC perpendicular with the connector and insert it firmly all the way. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Operation 3. Locking After FPC/FFC insertion, rotate the actuator down to a full stop, pushing it at the center. Rotate Rotate Excessive force after the actuator is already closed Push at the center of the actuator. Do NOT close at the ends. 4. FPC removal (Lock release) Carefully rotate the actuator up to 90°, lifting it at the center. Rotate (lift) Do not attempt to open more than 90° Lift at the center Do not open (lift) at one end. * The actuator opens by rotating it in the direction OPPOSITE to the direction of the insertion of the FPC. DO NOT attempt to open it from the same side as the insertion of the FPC. 10 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH39 Seriesq0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors Precautions when mounting connectors on the PCB xHandling before mounting on PCB Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED. xPC board warpage Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. xForces on the board xWhen braking the large PC board into individual boards exercise care NOT to damage the installed connectors. xWhen attaching the boards or other components with the screws make sure that any stresses will NOT cause board deflections affecting the mounting areas of the connector. Connector PCB Other precautions xWhen hand soldering: Do not perform hand soldering with the FPC inserted in the connector. • Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. • Do not use excessive amount of solder or flux compounds. Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. 11