FX5-80S2A-DSA

1mm Pitch Connector for Vertical Connection FX5 Series Connecting Height: Low profile FX5_*S2A_DSA FX5_*P_SH ( 3.6 ) PCB sFeatures 1. Header Side : 2 Types Available Two header types, low profile and high profile, are prepared according to the contact number variation and the connecting height variation, considering unit connections of HDD, FDD, CDROM and so on. Connecting Height: High profile FX5_*S2A_DSA FX5_*P_SH3 2. Two-stages Sequential Structure ( 6.6 ) The connecting sequence is designed with 2 stages so that the end user side can maintain. 3. Mating Guide In the connecting process, the self-alignment is ± 1mm high sufficient to the guide level, and the guide rib is provided to achieve easy mating. PCB 4. SMT Coplanarity The coplanarity of SMT soldered area secures the high accuracy of 0.1mm. 5. Miniaturization The connector is miniaturized about 30% in the mounting area, compared with the conventional half pitch connector (1.27mm). sApplications Note PC , other business equipments A206 sProduct Specifications Rating Current rating 0.5A Operating Temperature Range -55ç to +85ç (Note 1) Storage Temperature Range -10ç to +60ç (Note 2) 40% to 80% Storage Humidity Range 40% to 70% Voltage rating 100V AC Operating Humidity Range Item 1. Insulation Resistance 2. Withstanding voltage 3. Contact Resistance 4. Vibration 5. Moisture Resistance 6. Temperature Cycle 100M ohms min. Specifications 250V DC 300V AC/1 minute 100mA Condition No flashover or insulation breakdown. 50m ohms max. No electrical discontinuity of 1µs or more Contact resistance: 60m ohms max. Insulation resistance: 100M ohms min. Contact resistance: 60m ohms max. Insulation resistance: 100M ohms min. Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 96 hours at temperature of 40ç and humidity of 90% to 95% (-55ç: 30 minutes, 15 to 35ç: 2 to 3 minutes (-85ç: 30 minutes, 15 to 35ç: 2 to 3minutes) 5 cycles 500 cycles 7. Durability (Mating/un-mating) Contact resistance: 60m ohms max. 8. Resistance to Soldering heat No deformation of components affecting performance. Reflow: At the recommended temperature profile Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. sMaterial Part Insulator Header Contact Receptacle Contact Material Polyamide Brass Phosphor bronze Finish Beige Contact area : Gold plated Lead area : Tin-lead plated Remarks UL94V-0 ________ ________ Note : The black dots on the insulater will not affect performance. sOrdering Information qHeader FX5 q – * P – SH 3 w e r t q Series Name e Connector Type r Contact type SH : FX5 P: Header t Connector Height Blank 3 : 6.5mm : 9.5mm w Number of Contacts : 20, 40, 52, 56, 68, 80 : Right angle SMT type Note: The 56 contact header is for SH 3 type only. qReceptacle FX5 q – * S 2 A – DSA L w e r t y u q Series Name e Connector Type r Contact Sequence 2 t Serial No. : A : FX5 S: Receptacle : 2 Stages Sequence y Contact type DSA Blank L : Straight through hole type : Without board prefixed pin : With board Prefixed pin u Board prefixed pin w Number of Contacts : 20, 40, 52, 56, 68, 80 A207 sHeader Low profile High profile b1 ( 0.5) b1 b2 b* 9.5±0.3 ( 3.5 ) b2 b* 6.5±0.3 ** ** b1 b1 a1 6±0.3 6±0.3 a1 * = (number of contacts)/2 = a1 a2 1 A B±0.3 C±0.5 D±0.3 Polarity Mark a* a1 a2 1 a* 1.7±0.3 1.7±0.3 0 1_0.2 A B±0.3 C±0.5 D±0.3 Polarity Mark 0 1_0.2 9.3±0.3 9.3±0.3 a1 b1 a2 b2 0.5 E F±0.3 b* a* 1.4±0.3 2.5±0.3 a1 b1 a2 b2 0.5 E F±0.3 b* a* 1.4±0.3 2.5±0.3 ( Ø1.3 ) t0.2±0.05∞w0.2±0.05 2_Ø2.3±0.15 ( 1.3 ) 6.35±0.3 ( Ø1.3 ) t0.2±0.05∞w0.2±0.05 2_Ø2.3±0.15 ( 1.3 ) 6.35±0.3 G±0.1 3.2±0.2 2.5±0.3 3.2±0.2 2.5±0.3 G±0.1 Unit: mm Part Number FX5-20P-SH FX5-20P-SH3 FX5-40P-SH FX5-40P-SH3 FX5-52P-SH FX5-52P-SH3 FX5-56P-SH3 FX5-68P-SH FX5-68P-SH3 FX5-80P-SH FX5-80P-SH3 CL No. 575-0001-7 575-0041-1 575-0005-8 575-0045-2 575-0006-0 575-0046-5 575-1001-2 575-0008-6 575-0048-0 575-0009-9 575-0049-3 Number of Contacts 20 40 52 56 68 80 A 9 19 25 27 33 39 B 24 34 40 42 48 54 C 22.9 32.9 38.9 40.9 46.9 52.9 D 19 29 35 37 43 49 E 9.5 19.5 25.5 27.5 33.5 39.5 F 20 30 36 38 44 50 G 13.6 23.6 29.6 31.6 37.6 43.6 A208 sReceptacle 4.25±0.2 A ±0.2 a2 a1 b1 a1 1 a* ** 6±0.3 * = (number of contacts)/2 b1 b2 B ±0.3 5.9±0.2 C E F +0.1 – 0.2 b* E–E F–F 3.3±0.3 3.4±0.3 F E D ±0.3 1.5±0.2 1.5±0.2 1.5±0.2 0.6±0.3 t0.25±0.03xw0.4±0.05 3±0.3 Polarity Mark Unit: mm Part Number FX5-20S2A-DSA FX5-20S2A-DSAL FX5-40S2A-DSA FX5-40S2A-DSAL FX5-52S2A-DSA FX5-52S2A-DSAL FX5-56S2A-DSA FX5-56S2A-DSAL FX5-68S2A-DSA FX5-68S2A-DSAL FX5-80S2A-DSA FX5-80S2A-DSAL CL No. 575-0101-1 575-0121-9 575-0105-2 575-0125-0 575-0106-5 575-0126-2 575-0107-8 575-0127-5 575-0108-0 575-0128-8 575-0109-3 575-0129-0 Number of Contacts 20 40 52 56 68 80 A 9 19 25 27 33 39 B 19 29 35 37 43 49 C 15.08 25.08 31.08 33.08 39.08 45.08 D __ 15 __ 25 __ 31 __ 33 __ 39 __ 45 Order of Contact Sequence(Contact No.) 1 a1,a2,a9,a10 b1,b2,b9,b10 a1,a2,a19,a20 b1,b2,b19,b20 a1,a2,a25,a26 b1,b2,b25,b26 a1,a2,a27,a28 b1,b2,b27,b28 a1,a2,a33,a34 b1,b2,b33,b34 a1,a2,a39,a40 b1,b2,b39,b40 2 a3 to a8 b3 to b8 a3 to a18 b3 to b18 a3 to a24 b3 to b24 a3 to a26 b3 to b26 a3 to a32 b3 to b32 a3 to a38 b3 to b38 A209 BPCB mounting pattern qHeader FX5-*-SH, FX5-*-SH3 4±0.1 A ±0.1 B ±0.05 2.05±0.05 3.15±0.1 C ±0.05 0.5±0.02 0.3±0.03 (Land pattern) 0.25±0.03 (Metal mask) 4±0.1 (Mating side) (5.95) 2.55±0.1 2.1±0.1 a1 (Polarity mark position) b1 b2 a2 D±0.1 a* b* 2-Ø2.3 +0.1 0 2.15±0.1 3.4±0.1 * = (number of contacts)/2 2-Ø1.4±0.05 qReceptacle FX5-*S2A-DSA E ±0.1 1±0.05 a2 a1 (Polarity mark position) a3 a4 1.5±0.05 b4 b3 Ø0.6 +0.1 0 b* 1.5±0.05 1.5±0.05 b* 1.5±0.05 1.5±0.05 b4 b3 b2 Ø0.6 +0.1 0 * = (number of contacts)/2 * = (number of contacts)/2 F ±0.1 3±0.05 1±0.05 a2 a1 (Polarity mark position) a3 a4 a* E ±0.1 a* 1.5±0.05 b1 b2 FX5-*S2A-DSAL 2-Ø2.3 +0.1 0 b1 Unit: mm Number of Contacts 20 40 52 56 68 80 A 16 26 32 34 40 46 B 13.6 23.6 29.6 31.6 37.6 43.6 C 9.5 19.5 25.5 27.5 33.5 39.5 D 20 30 36 38 44 50 E 9 19 25 27 33 39 F 15 25 31 33 39 45 Note: If the connector is installed in the board beyond the above recommended size, it may cause the connector to board mounting failure or the soldering failure. It is desirable to implement the board process on the recommended PCB mounting pattern. A210 BRecommended Temperature Profile 250 Less than 5 seconds 230ç 200 Temperature (ç) 100 200ç Applicable Conditions 150 160ç 150ç Reflow system Solder Test board :IR reflow : Paste type 63 Sn/37 Pb (Flux content 9 wt%) : Glass epoxy 85mm x 60mm x 1.6 mm Metal mask thickness: 0.15 mm 50 25ç 0 START 30 seconds 60~90 seconds Preheating 60 120 Time (Second) 20~30 seconds Soldering Recommended temperature profile. The temperature may be slightly changed according to the solder paste type and amount. 60 seconds BCleaning Conditions 1. Organic Solvent Cleaning Solvent IPA (Isopropyl alcohol) HCFC (Hydrochlorophloro carbon) *Methylene chroride isn't suitable for this product solvent. Cold Cleaning Heat Cleaning 2. Liquid Cleaning When liquid detergents (such as terpene, alkali saponifier) are used, please select the cleaning detergent according to the influence table on metal or resin which is issued from each detergent manufacturer.In addition, please do not leave the connector outdoor, in which moisture remains. 3. Cautions for Cleaning As for organic solvent or liquid cleaning, if flux or detergent remains on the connector, it can cause electrical performance degradation. Therefore, please make sure that the connector is thoroughly cleaned so that neither flux nor detergent is found on the connector. A211 BConnector Precautions 1. Tolerance Clearance on Mating Side The effective connection clearance of the product is 1.6mm. Please use the product so as to specify within 1mm the clearance between the header and the receptacle in the connection process. 1 2. Header Connector Height The SMT connector height doesn't include the solder paste thickness. Thus, please consider that the stacking height will slightly increase after the mounting process. Mating Height: Low profile Mating Height: High profile FX5-*P-SH3 FX5-πP-SH ( 3.6) ( 6.6) PCB PCB 3. Screw Fastening Torque (SMT Type) When the screw is fastened, please use the M2 screw. The recommended fastening torque is 0.15(N.m) max. Nut (M2) Plain sheet (t = 0.3) Screw (M2) Board (t = 1.6) Spring sheet (t = 0.5) 4. Prefixed Process to Board (Through hole Type) If the prefixed process is required for board mounting, please use the prefixed pin type. (Applicable Thickness t = 1.6±0.1) Note: When the connector is mounted on the board, the dip post is guided into the board through-hole in order to prevent the dip post damage, and then insert the board in parallel to the connector so as to push in the prefixed pin. Dip post Prefixed pin PCB 5. Plug and Play When the connector is inserted or extracted in the active line state, please contact HRS company. 6. Others q It is noted that the forced excessive insertion/extraction will result in damage. q Avoid holding the board with the connector only, and fix the board by any other means except for the connector. q The color phase of this product may be slightly different from that of the forming product according to the manufacturing lot, but the difference doesn't affect the performance. A212