HMS08A18-10S-DT10D

NEW MS type Lower Profile Plug H/MS Series Circular connector conforming to MIL-C-5015 PAT.P Connector Height Comparison 18-10 Size 50.1mm 45.5mm 3057-10 70mm 54.5mm Existing MS Connector Lower-profile Plug 22-22 Size 48.2mm 53.2mm sFeatures 1. 20% Height Reduction When compared with existing H/MS Series connectors the overall height of plug assemblies is lower, allowing it to be used in space constrained applications. 78.7mm 41mm 3057-12 60.7mm 2. Cable Exit in 360° Directions The cable can exit in any of the 8 fixed direction, in 45° increments. Existing MS Connector Lower-profile Plug 3. Simple Assembly The 2-piece design consisting of the contact/insulator assembly and the back-shell assembly allows termination without the use of any specialized tools. Cable Exit Direction of 360° 4. Water and Dust Protection IP 67 rating when fully terminated and mated with corresponding part. 5. TUV Certification P rovided with a protective circuit function for TUV certification. The (D) pin is directly connected to the outside metal case. sApplications Factory automation equipment, robotic equipment, servo motors, and a wide variety of industrial and measuring instruments. Plug (45 °) Can be changed in 45 degree increments 45.8mm 63.8mm 56.5mm 18 22 3057-10 3057-12 2004.6 1 sProduct Specifications Voltage rating 250VAC, 250V DC (pollution degree: 3, overvoltage category: 3) 500V AC, 500V DC (pollution degree: 2, overvoltage category: 2) Current rating 23A Max. (18-10 size) 46A Max. (22-22 size) Operating temperature range -25ç to +125ç Storage temperature range -25ç to +125ç Rating Item Specification 18-10 size 22-22 size Conditions 1A DC 500 V DC 2250V AC/one minute. Frequency: 10 to 500 Hz, single amplitude of 0.75 mm, acceleration of 98 m/s2 for 3 hours in 3 axis. Acceleration of 490 m/s2, 11ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. 1. Contact resistance 3 m ohms max. 1 m ohms max. 2. Insulation resistance 5000 M ohms min. 3. Withstanding voltage No flashover or insulation breakdown. 4. Vibration No electrical discontinuity for 10 ms max. 5. Shock Contact resistance: Contact resistance: 6. Durability 500 cycles 4.5 m ohms max. 1.5 m ohms max. (insertion/ withdrawal) Temperature: -55ç ➝ Room temperature to +125ç ➝ Room temperature Time: 30 ➝ 10 to 15 ➝ 30 ➝ 10 to 15 (Minutes) 7. Temperature cycle Insulation resistance: 5000 M ohms min. 5 cycles. Insulation resistance: 50 M ohms min. (Humidity state) 96 hours at temperature of 71ç and humidity of 95% . 8. Humidity 500 M ohms min. (Dry state) No dust penetration. 9. Water/dust When mated with corresponding connector. No water penetration when submerged for 0.5 hour at the depth of 1 meter. protection sMaterials Item Body Insulator Socket Contacts Gasket Bushing Material Aluminum alloy PPS Copper alloy Silicone Rubber Chloroprene rubber Finish Black chromate Color: Black Silver plating Color: Black Color: Black Remarks ------------------UL94V-0 ------------------------------------------------------- sAdditional Product Information 1. Product number suffixes (10) Supplied with a wire hole in the locking ring (to prevent loosening of the ring). (11) Supplied without the wire hole in the locking ring. 2. Corresponding receptacles. 18-10 Size: Part number H/MS3102A18-10P-D-T1(10) 22-22 Size: Part number H/MS3102A22-22P-D-T(10) 2 sPlug H/MS08A18-10S-DT10D(10) 41 A Ø33.5 D B 18-10S C X 45.5 Part Number H/MS08A18-10S-DT10D(10) H/MS08A18-10S-DT10D(11) H/MS08A18-10S-DT10D1(10) H/MS08A18-10S-DT10D1(11) CL No. 120-0476-3-10 120-0476-3-11 120-0481-3-10 120-0481-3-10 Number of Contacts Weight 4 89g Ø10~Ø12.5mm H/MS08A18-10S-DT10C(10) Ø33.5 35.5 Part Number H/MS08A18-10S-DT10C(10) H/MS08A18-10S-DT10C(11) CL No. 120-0480-0-10 120-0480-0-11 Number of Contacts 4 Weight 77.6g H/MS08A22-22S-DT12D(10) A D Ø39.5 53.2 Part Number H/MS08A22-22S-DT12D(10) H/MS08A22-22S-DT12D(11) H/MS08A22-22S-DT12D1(10) H/MS08A22-22S-DT12D1(11) CL No. 120-0477-6-10 120-0477-6-11 120-0482-6-10 120-0482-6-11 Number of Contacts Weight 4 127g Ø10~Ø13.5mm 3057-10 31 Shown one type. Applicable Cable Diameter Contact solder pot inner diameter Ø12~Ø14.3mm 2.5mm 41 A D B 18-10S C X Ø30 Shown one type. Applicable Cable Diameter Contact solder pot inner diameter Ø13~Ø14.3mm 2.5mm 45.8 22-22S X B C 3057-12 36 Shown one type. Applicable Cable Diameter Contact solder pot inner diameter Ø13~Ø15.9mm 4.5mm 3 BAssembly Procedures Process Outline of assembly B B A Pre-solder Conductor portion A Contacts Back-shell B Solder Bushing 1 Insulator/contact assembly Washer A 18-10 Size 22-22 Size 24mm 33mm B 13mm 15mm Strain relief clamp a. Pass the strain relief clamp, washer, bushing, and hood over the cable, in this order. b. Prepare the cable and conductors per the dimensions in Table 1. c. Bend the exposed conductor to the B dimension as indicated in Table 1. d. Pre-solder the exposed conductor and solder it as shown to the exposed contact. Note: Use care not to damage the conductor’s insulation. 4.5 mm min. Back-shell Set screw (Hexagonal hole opposite side 1.27 mm) 3057-10 Locking ring 2 Table 2 Locking Ring 3 to 3.5N • m Cable Clamp 5 to 6N • m a. Place over the contact/insulator assembly (in the following order:Back shell, bushing, washer, strain relief clamp). b. Tighten the Locking ring and Cable clamp to the torque values per Table 2. c. Tighten the set screw to a torque value of 0.3-0.4 N-m HRS recommended tool: PB205/1.27 (CL150-0066-3)or equivalent. d. Using screwdriver tighten the two strain relief clamp screws until both sides of the moveable part are in contact with the cable clamp. ® 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933 http://www.hirose.com 4 The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements. 30 57 Table 1 -10 Cable Strain relief clamp Screw Cable Clamp Washer Bushing