HR34B-12WPA-10S

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. NEW Push-on Bayonet Lock Miniature Waterproof Connector HR34B Series Push-on Bayonet Lock Mating : Just inserting plug unit will complete mating Un-mating : Rotating sleeve to unlock mating fig.1 sFeatures 1. Water and dust protection • IP67 water and dust protection rating when fully mated. • Resistant to industrial grade oils. • 4-position receptacles are sealed against water penetration when mounted on the panel - no protective cap is required. Cable exit directions 45˚ 2. Easy and precise mating • Mating: Just inserting plug unit completes mating Unmating: Rotating sleeve counterclockwise unlocks connectors (fig.1) • Marking helps align plug with receptacle when mating. • 3 guide keys make blind mating possible. (Receptacle structure prevents plug from damaging receptacle terminals) fig.2 3. Multi-directional cable exit Right angle plugs allow the cable to exit in 8 directions, in 45˚ increments.(fig.2) 4. Safty standards ¨ The 4-position connectors meet requirements of T UV standard. 5. Wide variation Item Number of positions Connector type Terminations(plug) Terminations(receptacle) Conduit material Applicable cable size 4,10 straight plug,right angle plug,receptacle solder,crimp panel mount through-hole,wire solder plastic,metal Ø5.3~7.3, Ø6.5~8.0, Ø8.0~9.0(under development) 2010.52 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sSpecifications Current rating Ratings Voltage rating 10 pos.: 3 A 4 pos. : 5 A 10 pos.: 200 V AC, 250 V DC 4 pos. : 200 V AC, 200 V DC (contamination level 3) 400 V AC, 400 V DC (contamination level 2) Specification 30 mø max. 1,000 Mø min. No flashover or insulation breakdown No electrical discontinuity of 10 µs or longer No electrical discontinuity of 10 µs or longer Contact resistance: 30 mø max. Operating temperature range -25°C to 125°C Storage temperature range -25°C to 85°C Item 1.Contact resistance 2.Insulation resistance 3.Withstanding voltage 4.Vibration Conditions 1 A DC 500 V DC 10 pos. : 900 V AC / 1 minute 4 pos. : 2,000 V AC / 1 minute Frequency: 10 to 500 Hz/cycle, total amplitude of 0.75 mm, 98m/s2 each, 3 hours in 3 axis. Acceleration of 490 m/s2, 11 ms duration, 3 axis, each for 3 hours 500 cycles Temperature :-55°C / +15° to +35°C / +85°C / +15° to +35°C Time :-30 min. / 10 to 15 min. / 30 min. / 10 to 15 min. 5 cycles 336 hours at 71°C, and humidity of 95% 5.Shock 6.Durability (Mating / un-mating) 7.Temperature cycle Insulation resistance: 500 Mø min. 8.Humidity 9.Water protection Insulation resistance: 50 Mø min. (at high humidity) Insulation resistance: 500 Mø min. (when dry) No water penetration when submerged for 48 hours at the depth of 1.8 meters. sMaterials qPlugs Part Outer shell Insulator Female contacts O-ring Gasket 10 pos. 4 pos. Material Zinc alloy, aluminum alloy, and polyamide resin (black) PPS Phosphor bronze Copper alloy Fluororubber, Nitrile hydride rubber Finish Black chrome plating, black chromate finish (Cr +3) Color: Black Gold plated Silver plated --------------Remarks --------------UL94V-0 ------------------------------------------- qReceptacles Part Outer shell Insulator Male contacts Ground contact O-ring 10 pos. 4 pos. 10 pos. 4 pos. Material Zinc alloy PPS Copper alloy Brass Brass Fluororubber Finish Black chromate finish (Cr +3) Color: Black Gold plated Silver plated Gold plated Silver plated --------------Remarks --------------UL94V-0 ----------------------------------------------------------------------- 2 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sOrdering information qPlugs HR34B - 12 WP A - 10 S - X ( ** ) 1 1 Series name 2 Shell size 3 Shell style 2 3 4 5 6 7 8 (Excluding ground contacts) : HR34B Series : Diameter(mm) of the mating interface of the plug WP : Straight plug WLP : Right-angle plug 4 Conduit material and Applicable cable size A:Conduit material metal, Applicable cable Ø5.3~7.3 B:Conduit material metal, Applicable cable Ø6.5~8.0 D:Conduit material plastic, Applicable cable Ø5.7~7.3 E:Conduit material plastic, Applicable cable Ø6.5~8.0 K:Conduit material metal, Applicable cable Ø8.0~9.0(under development) 5 Number of contact : Number of contacts. 6 Contact type S : Female wire solder SC : Female crimp 7 Keying Blank : Standard X : X key position 8 Other specifications : 2 numerical digits wil be added when there is a specifications change other than shown in positions q to u qReceptacles HR34B - 12 WR A - 10 P - X ( ** ) 1 1 2 3 4 2 3 4 5 6 7 8 (Excluding ground contacts) Series name : HR34B Series Shell size : Diameter(mm) of the mating interface of the plug Shell style WR : Receptacl Shell type Blank : Rectangular flange type for 10 positions A : Square flange for 10 positions B : Square flange for 4 positions 5 Number of contact : Number of contacts. 6 Contact type P : Male,wire solder PD : Male,through hole contact 7 Keying Blank : Standard X : X key position 8 Other specifications : 2 numerical digits wil be added when there is a specification change other than shown in positions q to u qCrimp contacts HR34B - SC1 - 2 1 1 1 2 3 4 5 4 Conductor size : AWG#20 - 25 5 Plating 1:Gold plated 1 Series name : HR34B Series 2 Contact style : SC1:Female contact 3 Contact type 1 : 100pcs.per bag 2 : 10,000pcs per reel 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sStraight plugs qStandard type (Conduit material :Plastic) 49 Ø19 xWire solder Part Number HR34B-12WPD-10S HR34B-12WPE-10S HR34B-12WPD-4S HR34B-12WPD-4S-X HR34B-12WPE-4S HR34B-12WPE-4S-X HRS No. 134-0026-0-00 134-0027-2-00 134-0020-3-00 134-0023-1-00 134-0025-7-00 134-0031-0-00 Ø8.5 Ø6.5~8.0 A Ø7.4 Ø8.5 Ø7.4 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 Ø5.7~7.3 All dimensions: mm Solder cup inner diameter Ø1 Ø1.7 xCrimp (separate contacts required) Part Number HR34B-12WPD-10SC HR34B-12WPE-10SC HRS No. 134-0037-6-00 134-0038-9-00 A Ø7.4 Ø8.5 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 qRobust type(Conduit material :Metal) xWire solder Part Number HR34B-12WPA-10S(71) HR34B-12WPB-10S(71) HR34B-12WPK-10S HRS No. 134-0004-7-71 134-0007-5-71 Under development A Ø7.4 Ø8.5 Ø9.5 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 Ø8.0~9.0 Ø1 All dimensions: mm Solder cup inner diameter qCrimp (separate contacts required) Part Number HR34B-12WPA-10SC HR34B-12WPB-10SC HR34B-12WPK-10SC HRS No. 134-0017-9-00 134-0028-5-00 Under development A Ø7.4 Ø8.5 Ø9.5 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 Ø8.0~9.0 Not all cables of applicable dia. range can be easily assembled. Please kindly check with factory before use. 4 A The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sRight angle plugs qStandard type (Conduit material : Plastic) 33.5 Ø19 xWire solder Part Number HR34B-12WLPD-10S HR34B-12WLPE-10S HR34B-12WLPD-4S HR34B-12WLPD-4S-X HR34B-12WLPE-4S HR34B-12WLPE-4S-X HRS No. 134-0039-1-00 134-0040-0-00 134-0030-7-00 134-0034-8-00 134-0035-0-00 134-0036-3-00 Ø8.5 Ø6.5~8.0 A Ø7.4 Ø8.5 Ø7.4 30.85 B Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 Ø5.7~7.3 A B All dimensions: mm Solder cup inner diameter Ø1 Ø1.7 xCrimp (separate contacts required) Part Number HR34B-12WLPD-10SC HR34B-12WLPE-10SC HRS No. 134-0041-3-00 134-0042-6-00 A Ø7.4 Ø8.5 B 30.85 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 qRobust type (Conduit material :Metal) xWire solder Part Number HR34B-12WLPA-10S(71) HR34B-12WLPB-10S(71) HR34B-12WLPK-10S HRS No. 134-0005-0-71 134-0008-8-71 Under development A Ø7.4 Ø8.5 Ø9.5 31.5 B 30.5 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 Ø8.0~9.0 Ø1 All dimensions: mm Solder cup inner diameter qCrimp (separate contacts required) Part Number HR34B-12WLPA-10SC HR34B-12WLPB-10SC HR34B-12WLPK-10SC HRS No. 134-0018-1-00 134-0029-8-00 Under development A Ø7.4 Ø8.5 Ø9.5 31.5 B 30.5 Applicable cable diameter range Ø5.7~7.3 Ø6.5~8.0 Ø8.0~9.0 Not all cables of applicable dia. range can be easily assembled. Please kindly check with factory before use. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sReceptacles xWire solder 48) 2. (R 1 3 7 4-Ø 3.2 B A 4 8 10 A B All dimensions: mm Part Number HR34B-12WRA-10P HR34B-12WRB-4P HR34B-12WRB-4P-X HRS No. 134-0016-6-00 134-0021-6-00 134-0024-4-00 A 17.26 18.26 B 23.4 25.4 Solder cup inner diameter Ø1 Ø1.3 O ring for water proof is not attached. Please find appropriate one from the market. xThrough hole 3.3 5.8 8.55 20 13.4 2 3.2 4-Ø Part Number HR34B-12WR-10PD(71) HRS No. 134-0003-4-71 O ring for water proof is not attached. Please find appropriate one from the market. sCrimp contacts xFemale 15 1.2 Part Number HR34B-SC1-111 HR34B-SC1-211 CL No. 134-0051-7-00 134-0050-1-00 Packaging 100 pcs. per bag 10,000 pcs. per reel Applicable conductor AWG #20 - 25 (Stranded wire) Note: Use wire with a jacket diameter of 1.7mm max. 6 32.4 39 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sConnector Mating Combinations 10 pos. Plugs Straight, Wire Solder or Crimp (Standard key position) HR34B-12WPA-10S,10SC HR34B-12WPB-10S,10SC HR34B-12WPD-10S,10SC HR34B-12WPE-10S,10SC HR34B-12WPK-10S,10SC 10 pos. Receptacles Through hole HR34B-12WR-10PD Right angle, Wire Solder or Crimp (Standard key position) HR34B-12WLPA-10S,10SC HR34B-12WLPB-10S,10SC HR34B-12WLPD-10S,10SC HR34B-12WLPE-10S,10SC HR34B-12WLPK-10S,10SC Wire Solder HR34B-12WRA-10P 4 pos. Plugs Straight, Wire Solder (Standard key position) HR34B-12WPD-4S HR34B-12WPE-4S Standard polarizing key 4 pos. Receptacles Wire solder (Standard key position) HR34B-12WRB-4P Right angle, Wire Solder (Standard key position) HR34B-12WLPD-4S HR34B-12WLPE-4S Standard key position Straight, Wire Solder (X key position) HR34B-12WPD-4S-X HR34B-12WPE-4S-X Wire solder (X key position) HR34B-12WRB-4P-X Right angle, Wire Solder (X key position) HR34B-12WLPD-4S-X HR34B-12WLPE-4S-X X key position X key position 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector sApplicable tools Description Manual contact crimping tool Press Applicator Contact extraction tool Part Number HT304/HR34B-1 CM-105 AP105-HR34B-1 RP6-SC-TP CL No. 150-0107-9 901-0005-4 901-2051-2 150-0039-0 HR34B-SC1-111 HR34B-SC1-211 Applicable contact HR34B-SC1-111 HR34B-SC1-211 Applicable cable AWG20,AWG23,AWG25 AWG20 to AWG25 --------------- qManual contact crimping tool qPress CM-105 (Applicator ordered separate) qContact extraction tool sIllustrations of mated connectors. Right-angle plug Mating Combinations 10 pos. plug shell A,B type. Plug + receptacle through-hole Plug + receptacle wire solder Plug + receptacle through-hole Plug + receptacle wire solder Plug + receptacle through-hole Plug + receptacle wire solder A 31.0 31.5 31.3 31.8 32.0 32.5 31.3 10 pos. plug shell D,E type. 10 pos. plug shell K type. (33.5) 4 pos.plug + receptacle wire solder B A Straight plug Mating combinations 10 pos.plug + receptacle through-hole 10 pos.plug + receptacle wire solder 4 pos.plug + receptacle wire solder B 49.6 50.1 49.6 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector BRecommended panel cutouts qReceptacle - wire solder 4-B All dimensions: mm HR34B-12WRA-10P HR34B-12WRB-4P HR34B-12WRB-4P-X 18.26±0.05 M3∞0.5 1 0/-0.1 12.5 +0.1/0 17 +0.1/0 1.1 0/-0.1 16.3 +0.1/0 20.8 +0.1/0 A A B C A 17.26±0.05 D E C Recommended O ring dia. Part Number ØD ØE Cross-section 1.5 1.5 diameter 11.5 15.5 HR34B-12WRA-10P HR34B-12WRB-4P HR34B-12WRB-4P-X qReceptacle - through hole O-ring (Not supplied, cross-section diameter 1.78 , inner diameter 20.35) (13.4) 4(R 5. 2) All dimensions: mm (2.3)(xxx) (22.4) (1.3) 4-M3∞0.5 (13.4) (18) (13.6) Outline of the O-ring Notes 1: The receptacle panel cutout shows the view from the mating side of the connector. BPCB mounting pattern qReceptacle - Through hole 2.15 2.4 17 0° ±3 4.4 2.15 1 0. +0 (32.4) All dimensions: mm in al ) 7 Ø1 10 5.5 1 3 4 8 .9 +0.1 2.4 Alignment mark 1.4 +0 .0 05 0 -Ø0 (Po siti 10 1.2 3.6 2-Ø 1.2 3.6 (G 0 r n ou d te rm oni ng pos t) N ote 3 Note 1: The contact configuration shows the view from the mating side. Note 2: Tolerance of ±0.05 mm is recommended for the plated through hole location and diameter. Note 3: Not a plated-through holes. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. HR34B SeriesqPush-on Bayonet Lock Miniature Waterproof Connector BReceptacle Contact Arrangement 4 pos.wire solder 10 pos.wire solder 10 pos.through hole 1 2 3 4 1 5 8 2 6 9 3 7 10 4 1 5 8 2 6 9 3 7 10 note.1 View direction:Mating surface of pin insert. note.2 mark is ground terminal. BHandling 1. Mating 2. Un-mating Receptacle Plug Locking collar B A Rotate counter-clockwise Mating position alignment marks Holding the plug by the outer shell (A) align the arrow on the plug with the alignment mark on the receptacle and push straight in. Rotate the locking collar counter-clockwise to a full stop and unmate the plug from the receptacle. BPrecautions Center line of the connector When completely mated and locked the alignment arrow on the plug must line-up with the center line of the connector (alignment mark on the receptacle). Alignment mark If the alignment arrow and the center line of the connectors are not aligned (1 mm max.) re-insert the plug until they are aligned. 1 mm max. 1. When disconnecting or inserting the connector, be sure to do so after turning off the power. 2. To insert the connector, push it in until the arrow tip of the plug mating mark indicates the specified position of the diagram below (i.e., the mating mark of the receptacle). 3. Note that the display method of the mating mark will differ depending on the receptacle. 4. To maintain the waterproof quality and cable clamp force, use a cable that is within the range of the applicable cable diameter. 5. Please consult Hirose Electric Sales for harness assembly procedure. 10