POD3-R-1

Push-Pull Complete Locking Coaxial Connectors (PC Card Type 2 Mountable) POD3 Series Board Mounting Example sFeatures 1. Excellent push-pull complete locking method for ease of operation The connector coupling portion uses a Hirose Electric original push-pull complete locking system. 1) A sure lock is obtained by holding the connector outside tube portion and just giving it a light push. 2) Positive lock prevents easy disconnection. To remove the connector, just hold the connector outside tube portion and pull for a simple release of the lock 2. Type II PC Card Mountable The receptacle thickness is 3.9 mm which permits mounting to the back side of a type II card. (Note) that at the time of card mounting, use of 0.3mm offset of the board mounting surface from the card center line will result in the same card center axis and connector center axis. 3. High Degree of Matching The top-touch system used for the coupling method achieves high frequency performance from 0 to 3 GHz with a V.S.W.R. of 1.3 or less. 4. Ultra-Miniature sApplications Wireless LAN cards, GPS cards, and miniature wireless communications devices. As a complete locking type, this series achieves a size reduction of approximately 50% in the direction of the diameter as compared to our original POD1 Series. 5. Accommodates Ultra-Fine Cable These connectors accommodate the use of ultra-fine coaxial Teflon cable which permits high-density wiring inside equipment. Ø1.48 (single-layer shielded cable) ....CO-6F FH-SB manufactured by Hitachi Cable, Ltd. ....DFS111-UL1979 manufactured by Junkosha Co., Ltd. sFunction Diagrams Jack Side sJack POD3-J-DFS111 Plug Side sPlug Receptacle POD3-PR-1 sReceptacle POD3-R-1 sConversion Adapter (Coupling portion: SMA side jack - POD3 side jack) sConversion Adapter (Coupling portion: SMA side jack - POD3 side plug) HRMJ-POD3J HRMJ-POD3P B23 s Product Specifications Nominal characteristic impedance Ratings Voltage Frequency 50 ohms 100 V AC DC to 3 GHz Operating temperature Operating humidity -30C° to +85C° 95% max. Item 1. Contact resistance 2. Insulation resistance 3. Withstanding voltage 4. V.S.W.R.(*) 5. Female contact retention Specification Inner : 10 m ohms max. Outside: 5 m ohms max. 500 M ohms min. No flashover or insulation breakdown. 1.3 max. 0.2 N min. 100 mA max. 250 V DC 300 V AC / 1 minute DC to 3 GHz Condition Measured with a Ø0.3 pin gauge With corresponding connector 6. Insertion and withdrawal force (plug) 1.96 N min. 7. Durability (Insertion/withdrawal) 8. Vibration Contact resistance: Amount of change 10 m ohms max. 250 cycles No electrical discontinuity of 1µs or more No damage, cracks, or parts looseness. No electrical discontinuity of 1µs or more No damage, cracks, or parts looseness. Insulation resistance 100 M ohms min. (at high humidity) 500 M ohms min. (when dry) No damage, cracks, or parts looseness. Frequency: 10 to 500 Hz, single amplitude of 0.75 mm or acceleration of 98 m/s2(peak), 2 hours in each of the 3 directions. Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 10 cycles in each of the 3 axis 240 hours at temperature of 25ç to 65ç and humidity of 90% to 96% Temperature: -55°C ¡ 5 to 35°C ¡ 85°C ¡ 5 to 35°C Time: 30 min ¡ Within 5 min ¡ 30 min. ¡ Within 5 min Cycles: 5 Exposed to density 5% salt water for 48 hours 9. Shock 10. Humidity (Steady state) 11. Temperature cycle 12. Salt spray No damage, cracks, or parts looseness. No marked corrosion *Voltage standing wave ratio (V.S.W.R.) measuring system. The above voltage standing wave ratio (V.S.W.R.) standard value is measured in the measuring system as shown below. Network Analyzer Test Set Test Port D.U.T Test Port Cable Termination Note1: The cable connector is measured with double ended 10cm cable assembly. Note2: The printed circuit board connector is mounted on the 50 ohms PCB, to which Hirose's adaptor is connected. sMaterials part Body Insulator Female inner contact Male vinnerr contact Spring coil Heat-shrink tubing Material Brass/Phosphor bronze PTFE Beryllium copper Phosphor bronze Piano wire Polyolefin Finish Gold and nickel plating/Gold plating —————— Gold plating Gold plating Nickel plating —————— s Ordering Information POD3 – [ q q Series name: POD3 w Connector types J : Jack R : Receptacle PR : Plug receptacle ]–[ w e ] e Applicable cable or suffix DFS111: CO-6F FH-SB manufactured by Hitachi Cable, Ltd. DFS111-UL1979 manufactured by Junkosha Co., Ltd. B24 sJack Ø3.8 11 CL No. 327-0152-2 Part Number POD3-J-DFS111 sReceptacle Ø3.5 Ø0.6 5 0.6 7 8.3 3.5 CL No. 327-0154-8 Part Number POD3-R-1 sPlug Receptacle Ø3.85 Ø0.6 5 0.6 3.9 6.7 8 3.9 CL No. 327-0153-5 Part Number POD3-PR-1 sConversion Adapter qSMA conversion adapter (Coupling portion: SMA side jack - POD3 side plug) 13.9 9.5 1/4-36UNS-2A 8HEX Ø3.85 CL No. 311-0285-0 Part Number HRMJ-POD3P qSMA conversion adapter (Coupling portion: SMA side jack - POD3 side jack) 14.2 9.5 1/4-36UNS-2A 8HEX Ø3.5 CL No. 311-0286-3 Part Number HRMJ-POD3J 3.9 B25 sConnector Mounting Condition The mounting reference diagram is an anticipated diagram of the condition of mounting to a frame offset 0.3 mm from the card center line. 0.3 PCB sPCB mounting pattern (7.5) 6 (Ø 0.5 through hole) (1) 4 +0.1 +0 5Max 3.5 (2) 3.9 1min Corner escape portion Pad Copper foil portion (Resist layer beyond the pad) B26 2 4