RP34L-5P-2SC

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Low Profile Connectors for AC power supply RP34L Series Receptacle installed height (3 pos.type) (2 pos.type) RP34L Existing RP34 sFeatures 1. Low profile Receptacles are designed with their installation heights to be shorter than those of conventional RP34 series. Mated dimensions 2. Space saving Both 2 and 3 position receptacles are miniaturized to 7mm length, resulting in a small board mounting area. 3. Snap-lock mechanism Audible click when connector is fully mated. 4. Precise mated connection Secure hold of the plug on au 3 axis. RP34L-5PA-2SC(✽✽✽✽) & RP34L-5R-2PD 5. Sequence mating The 3 contact type has sequenced mating. One pin makes contact as a ground terminal before the other contacts. This 2 contact plug is an over-molded (i.e., cable-integrated form) type. Recommended cable diameter is 3.5mm dia. 6. No Mismating Two polarized keys prevent any insertion error. Mated dimensions 23.5 16.9 7. Ease of Mating An arrow on the top of the plug shows the proper direction for insertion. 10.45 7 1.4 7.8 9.1 5 sApplications Notebook PCs, portable remote terminals, AV equipment, etc. RP34L-5PA-3SC & RP34L-5R-3PD This 3-contact plug is a field assembly type. Recommended cable diameter is 4mm dia. 2006.8 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. sProduct Specifications Ratings Current rating Voltage rating 5A 30V AC, 42A DC Specification 30mø or max. 1A DC 100V DC 150V AC/1 minute 10~55Hz, one-sided amplitude 0.75mm, 3 directions for 2hours, respectively -55ç for 30 min./normal temp. for 10~15 min./+85ç for 30 min./normal temp. for 10~15 min. 5 cycles 5% salt water solution, 48 hours 5,000 mating / un-mating Operating temp. range Storage temp. range -25ç~+85ç -10ç~+60ç Conditions Item 1.Contact resistance 2.Insulation resistance 1000mø min. 3.Withstanding voltage No flashover or insulation breakdown 4.Vibration 5.Temperature cycle 6.Salt spray 7.Durability No electric disconnection of 10µs or more Insulation resistance:100mø min. No corrosions Contact resistance:60mø max. sMaterial Component Metal comp. 2 pos. Insulator Contacts Cover 2 pos. Insulator Contacts Metal comp. 3 pos. Insulator Contacts Cover 3 pos. Insulator Contacts Nylon Brass Vinyl chloride Nylon Phosphor bronze Phosphor bronze PPS Brass Polycarbonate Vinyl chloride PPS Phosphor bronze Solder-plating Black Palladium-plating Black Black Black Palladium-plating Material Phosphor bronze Finish / Color Solder-plating Black Palladium-plating Black Black Remarks --------------UL94HB --------------UL94V-0 UL94HB ----------------------------UL94V-0 --------------UL94V-0 UL94V-0 UL94V-0 --------------- sOrdering information RP34L - 5 PA - 2 SC 1 1 Series name: RP34L 2 Shell: Shell.size, 5 3 Type: Receptacle: R Assembled straight plug: P Assembled right angle plug: LP Cable ass'y, straight plug: PA 2 3 4 5 (✽ ✽ ✽ ✽ ) 6 4 Number of contacts: 2, 3 5 Type of contact: PD: through hole male contact SC: crimp female contact 6 Cable length:(✽✽✽✽) depends on each cable (mm). 2 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. sReceptacles q2 pos. RP34L-5R-2PD(71) Recommended panel cutout PCB mounting pattern Connector front q3 pos. RP34L-5R-3PD(71) Recommended panel cutout PCB mounting pattern Connector front Part Number RP34L-5R-2PD(71) RP34L-5R-3PD(71) CL No. 113-5154-6-71 113-5157-4-71 RoHS YES 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. sPlugs sRP34L-5PA-2SC(1857)(71) Cable assembly sRP34L-5PA-3SC(71) Field assembly-Straight sRP34L-5LP-3SC(71) Field assembly-Right angle Part Number RP34L-5PA-2SC(1857)(71) RP34L-5PA-3SC(71) RP34L-5LP-3SC(71) CL No. 113-5153-3-71 113-5178-4-71 113-5161-1-71 RoHS YES 4 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. sCrimp contact sRP34L-SC1-212(01) Part Number CL No. RoHS RP34L-SC1-212(01) 113-5151-8-01 YES sApplicable Tools Type Manual crimping tool Automatic Crimper Crimper body Cable crimping tool Drawing tool AP105-RP34L-SC1-212 RP34-TC-01 RP6-SC-TP Part Number HT-102/RP34L-SC1-212 CM-105 CL No. -------------- Applicable contact RP34L-SC1-112(01) -------------- Applicable conductor AWG#18~#22 -------------- 901-0005-4 901-2043-4 150-0074-1 150-0039-0 RP34L-SC1-212(01) --------------------------- AWG#18~#22 Ø4 -------------- 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. sAssembly Instructions(3-Position Plug) qStraight Plug 1. Slide the bushing over the cable. 2. Prepare the cable end and the conductors as shown. 3. Crimp the contacts to each conductor. Verify the crimp dimensions. 4. Insert each of the contacts into the insulator body. Verify that the contact is secure by slightly pulling on the conductor. Should the contacts require reinsertion, use the tool RP6-SC-TP to remove them (Inserted from the termination side). 5. Crimp the cable clamp over the cable at designated dimension (Tool number:RP34-TC-01). 6. Place the outer case on a flat surface , with inside facing up. 7. Carefully place the insulator body, clamp and the bushing into corresponding indents and cut-outs in the outer case. Verify correct location. (As shown on drawing) Note A: When placing all components in the case, exercise caution as NOT to damage any of the protruding snap. Note B: All components should fit easily, without use of any force. 8. Carefully align the other outer case over all components case. Do not force alignment. 9. Snap the case in place. Outer case Outer case Outer case Outer case qRight Angle Plug Insulator body 1. The right angle plug can also be assembled by using the same procedure as the straight plug. Outer case Insulator body 6 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. sPrecautions 1. Use the connector section with its panel held down so as not to have excessive load.For 2-contact type, hold the outer shellsection of the receptacle, and for 3 contact type, the outer shell section of the plug. Panel 2. After connector assembly, cable must not be pulled over 30N in the arrow-indicated direction. Be careful not to add excessive tensile load because it will lead the damage of connectors. 7