TM21P-88P

NEW Modular Plug Connectors Compliant to Enhanced Category 5 Standards TM21P Series (Shielded Type) TM22P-88P (Non-shielded Type) sFeatures 1. Supports High-Speed LAN Transmission Conforms to requirements of TIA/EIA-568B data wiring standard, meeting transmission performance of Enhanced Category 5. Supports Gigabit Ethernet (1000BASE-T) and Fast Ethernet (100BASE-TX) high-speed LAN transmission. Protected latch tab 2. EMI protection (TM21*P-88P) 360° coverage of the engagement area with a metal shield assures protection against electromagnetic interference. When mated with corresponding connector the shield surfaces are securely connected to provide continuous circuit. 3. Protected latch tab (TM21P-88P) Flexible case extends over the release tab preventing the possibility of breaking-off during handling of the complete cable assembly. 4. Termination of conductors Self located 24 AWG conductors (solid or stranded) are terminated against pre-inserted contacts using simple tooling. ① 5. Simplified termination (TM21*P-88P) Removeable one piece cover allows easy access to the termination areas. ② ① 6. Conforms to the ISO 8877 Standard (ISDN Interface Connector) ① sApplications Telecom Hubs, Routers, Bridges and ATM Transmission Equipment, Ethernet Switches and Networking Equipment, Test and Measurement Equipment and other equipment requiring this type of simple and reliable connection. Cover Installation Procedure 2002.11 1 sProduct Specification Current rating Rating Voltage rating 125 V AC 1A Operating temperature range-25ç to +60ç (Note) Item 1. Insulation resistance 2. Withstanding voltage (between adjacent contacts) 3. Withstanding voltage (between contact and shield) 4. Contact resistance 5. Vibration 6. Shock 7. Durability (mating/un-mating) 8. Temperature cycle 100 M ohms min. Specification 100 V DC Conditions No flashover or insulation breakdown No flashover or insulation breakdown 230 m ohms max. No electrical discontinuity of 5 ms or more Contact resistance: 250m ohms max. No electrical discontinuity of 5 ms. min. Contact resistance: 250m ohms max. Contact resistance: 250m ohms max. Contact resistance: 250 m ohms max. Insulation resistance: 100 M ohms min. 500 V AC / one minute 1500 V AC / one minute 100mA DC Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours / 3 axis Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis 200 Temperature: -55ç/+5ç to +35ç/+85ç/+5ç to +35ç Duration: 30/5/30/5(Minutes) 5 cycles 500 hours at temperature of 40ç and humidity of 90% to 95% Exposed to density 5% salt water for 48 hours 9. Humidity Contact resistance: 250 m ohms max. Insulation resistance: 1 M ohms min. (High humidity) Insulation resistance: 10 M ohms min. (Dry state) Contact resistance: 250 m ohms max. 10. Salt Spray Note :Includes temperature rise caused by current flow. sMaterials Part Insulator Contacts Shield Conductor holding tray Cover Material Polycarbonate Copper alloy Copper alloy Polycarbonate Polyamide Finish Color: Clear Contact area: Gold plating Solder plating Color: Clear Color: Light beige (Note) Remarks UL94V-2 ------------UL94V-2 UL94V-2 Note :Cover available in various colors. Refer to page 3. sOrdering information qPlugs- Shielded qPlugs - Non-shielded TM21 C P - 8 8P 1 1 Series name 2 Cover Type 3 Size 4 Inserted contacts 2 1 3 4 TM21P: Shielded Blank: Protective latch cover C: Short cover 8: For 8 contacts 8P: 8 TM22P - 8 8P 1 1 Series name 2 Size 3 Inserted contacts 2 3 TM22P : Non-shielded 8 : For 8 contacts 8P: 8 2 sPlug Connectors qShielded ) 3.5 (R 6.7 Cover 6.09 11.7 17.5 12.9 (34) 9 30.2 16.6 29.5 Contact No. 1 (0.6) 6.6 Contact No.8 5.4 9.05 Part Number TM21P-88P TM21P-88P(02) TM21P-88P(03) TM21P-88P(04) TM21P-88P(05) TM21P-88P(06) TM21P-88P(07) TM21P-88P(08) TM21P-88P(09) CL No. 222-2862-9-02 222-2862-9-02 222-2862-9-03 222-2862-9-04 222-2862-9-05 222-2862-9-06 222-2862-9-07 222-2862-9-08 222-2862-9-09 Cover Color Light beige Medium gray Black Natural light gray Red Green Blue Yellow Orange BCover installed BMated with corresponding receptacle (shown for reference only) (34) (13.4) (44.65) 3.45 Conductor holding tray 3 sPlug Connectors qShielded-Short Cover 6.7 17.2 Cover 6.09 11.7 10.4 TM21CP-8 30.2 (22.4) 9 6.6 (0.6) 12.9 (R 17.5 3. 5) Contact No.1 Contact No.8 5.4 9.05 Part Number TM21CP-88P(03) CL No. 222-2884-1-03 Cover color Black Note: For other colors contact Hirose sales representative. BCover installed BMated with corresponding receptacle (shown for reference only) (21.7) (13.4 ) (32.35) BApplicable Shielded Cable Specifications Specifications Solid copper conductor: 0.5mm dia. Jacket Shield Insulation Conductor TM21CP-8 Conductor Stranded copper conductor: AWG#24 (Dia. 0.2mm x 7 pcs) Individual conductor insulation dia. (0.9mm to 1.0mm) Drain wire Drain wire AWG#26 (tin coated) Overall jacket dia. (dia. 6.6mm) Note: For cable termination procedures refer to: [TM21P-88P Cable Termination Procedure Manual] (ETA-E2349) and [TM21CP-88P Cable termination Procedure Manual] (ETA-E2353). Some cables may not meet the required service ratings. Contact Hirose sales representative for specific cable applications recommendations. 4 3.45 Conductor holding tray TM21CP-8 TM21CP-8 sPlug Connectors qNon-shielded 22.5 6.09 11.7 5.4 14.2 9.05 7.9 Contact No.1 (0.6) 6.6 Contact No.8 Part Number TM22P-88P CL No. 222-2899-9 BMated with corresponding receptacle (shown for reference only) (11.85) BApplicable Non-shielded Cable Specifications Specifications Jacket Solid copper conductor: 0.5mm dia. Conductor Stranded copper conductor: AWG#24 (Dia. 0.2mm x 7 pcs) Individual conductor insulation dia. Conductor Insulation (0.9mm to 1.0mm) Overall jacket dia. (dia. 5.4mm to 5.7mm) Note: For cable termination procedures refer to: [TM22P-88P Cable Termination Procedure Manual] (ETA-E2381). Some cables may not meet the required service ratings. Contact Hirose sales representative for specific cable applications recommendations. 3.45 Conductor holding tray 5 BHand termination tools qFor contact/conductor termination Part Number HT205/TM21P-88P CL No. 250-0234-4 qFor cable and shield crimping (Shielded connectors only) Part Number HT206/TM21P-88P CL No. 250-0235-7 qFor contact/conductor termination (Non-shielded connectors) Part Number HT501/TMP-88 CL No. 902-2111-9* *Scheduled for release soon. Please contact your Hirose Electric account representative for information. 6 BTechnical Documentation qCAT5e Transmission Characteristics Data These are the representative values of the various transmission characteristics data for connector assemblies TM21P-88P and TM21R-5C-88-LP when fully mated. All plugs in the TM21R-5C Series that were manufactured based on the De-embedded method of the TIA/EIA568-B.2 standard meet requirements of CAT5e single transmission performance. • Signal Attenuation 0.5 Attenuation(dB) 0.4 0.3 0.2 0.1 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec (Each two numbers are for the pair of individual contact position.) • Near-End Crosstalk Attenuation (NEXT) 120 100 NEXT(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2-3,6 1,2-4,5 1,2-7,8 3,6-4,5 3,6-7,8 4,5-7,8 CAT5e Spec • Return Loss 80 Return Loss(dB) 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec 7 • Far-End Crosstalk Attenuation (FEXT) 120 100 FEXT(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2-3,6 3,6-4,5 4,5-7,8 CAT-5e Spec 1,2-4,5 3,6-7,8 7,8-1,2 1,2-7,8 4,5-1,2 7,8-3,6 3,6-1,2 4,5-3,6 7,8-4,5 (Each two numbers are for pair of individual contact position.) • Propagation Delay 3 2.5 Delay(ns) 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec • Propagation Delay skew 1.4 1.2 Delay Skew(ns) 1 0.8 0.6 0.4 0.2 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) Measurement Value CAT5e Spec Creativ e ks to World El e Lin HIROSE ELECTRIC CO., LTD. 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE:81-3-3491-9741 FAX:81-3-3493-2933 http://www.hirose.com 8 The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements. onics ctr