347LP3E

HMC347LP3 / 347LP3E v06.0805 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 14.0 GHz Features High Isolation: >50 dB up to 3 GHz >45 dB up to 10 GHz Low Insertion Loss: 1.6 dB @ 10 GHz Non-Reflective Design 3x3 mm QFN SMT Package Typical Applications The HMC347LP3 / HMC347LP3E is ideal for: • Basestation Infrastructure • Fiber Optics & Broadband Telecom • Microwave Radio & VSAT 8 SWITCHES - SMT • Military Radios, Radar, & ECM • Test Instrumentation Functional Diagram General Description The HMC347LP3 & HMC347LP3E are broadband high isolation non-reflective GaAs MESFET SPDT switches in low cost leadless QFN surface mount plastic packages. Covering DC to 14 GHz, the switch offers high isolation and low insertion loss. The switch features >50 dB isolation up to 3 GHz and >40 dB isolation up to 13 GHz. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply. This SPDT is an excellent alternative to the HMC132C8 SPDT. Electrical Specifications, TA = +25° C, With 0/-5V Control, 50 Ohm System Parameter Frequency DC - 3.0 GHz DC - 6.0 GHz DC - 12.0 GHz DC - 14.0 GHz DC - 3.0 GHz DC - 6.0 GHz DC - 12.0 GHz DC - 14.0 GHz “On State” “Off State” DC - 6.0 GHz DC - 14.0 GHz DC - 6.0 GHz DC - 14.0 GHz 0.5 - 14.0 GHz 0.5 - 14.0 GHz 49 41 39 33 10 8 7 6 19 38 Min. Typ. 1.5 1.6 1.6 1.9 53 46 44 38 13 13 10 9 23 43 Max. 1.9 2.0 2.1 2.4 Units dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm Insertion Loss Isolation Return Loss Return Loss RF1, RF2 Input Power for 1 dB Compression Input Third Order Intercept (Two-Tone Input Power= +7 dBm Each Tone) Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) DC - 14 GHz 3 6 ns ns 8 - 208 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC347LP3 / 347LP3E v06.0805 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 14.0 GHz Insertion Loss 0 Isolation 0 -10 INSERTION LOSS (dB) -1 ISOLATION (dB) -20 -30 -40 -50 -60 -5 0 5 10 FREQUENCY (GHz) 15 20 -70 0 5 10 FREQUENCY (GHz) 15 20 RF1 RF2 -2 +25 C +85 C -40 C -3 8 SWITCHES - SMT 8 - 209 -4 Return Loss 0 RFC RF1,RF2 ON RF1,RF2 OFF 0.1 and 1 dB Input Compression Point 30 1 dB Compression Point 0.1 dB Compression Point -5 RETURN LOSS (dB) -10 INPUT P1dB (dBm) 25 20 -15 15 -20 -25 0 5 10 FREQUENCY (GHz) 15 20 10 0 2 4 6 8 10 12 14 16 FREQUENCY (GHz) Input Third Order Intercept Point 50 45 INPUT IP3 (dBm) 40 35 +25C -40C +85C 30 0 2 4 6 8 10 12 14 16 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC347LP3 / 347LP3E v06.0805 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 14.0 GHz Absolute Maximum Ratings RF Input Power (Vctl = -5V) Control Voltage Range (A & B) Hot Switch Power Level (Vctl = -5 V) Channel Temperature +27 dBm +0.5V to -7.5 Vdc +23 dBm 150 °C 0.12 W 440 °C/W 540 °C/W Control Voltages State Low High Bias Condition 0 to -0.5V @ 10 uA Max. -5V @ 10 uA Typ. to -7V @ 40 uA Typ. (± 0.5 Vdc) 8 SWITCHES - SMT Continuous Pdiss (T=85 °C) (derate 2mW/ °C above 85 °C) Thermal Resistance (Insertion Loss Path) Thermal Resistance (Terminated Path) Storage Temperature Operating Temperature ESD Sensitivity (HBM) Truth Table Control Input A High Low B Low High Signal Path State RFC to RF1 On Off RFC to RF2 Off On -65 to +150 °C -55 to +85 °C Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 8 - 210 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC347LP3 / 347LP3E v06.0805 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 14.0 GHz Outline Drawing 8 SWITCHES - SMT Package Marking [3] 347 XXXX 347 XXXX NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC347LP3 HMC347LP3E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 211 HMC347LP3 / 347LP3E v06.0805 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 14.0 GHz Suggested Driver Circuit 8 SWITCHES - SMT Pin Descriptions Pin Number 1, 5, 9, 12, 16 Function N/C Description This pin should be connected to PCB RF ground to maximize isolation Package bottom has exposed metal paddle that must also be connected to PCB RF ground. This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. See truth table and control voltage table. Interface Schematic 2, 4, 6, 8, 13, 15 GND 3, 7, 14 RFC, RF1, RF2 10 CTLB 11 CTLA See truth table and control voltage table. 8 - 212 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC347LP3 / 347LP3E v06.0805 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 14.0 GHz Evaluation PCB 8 SWITCHES - SMT List of Materials for Evaluation PCB 105711 [1] Item J1 - J3 J4 - J6 R1 - R2 U1 PCB [2] Description PCB Mount SRI SMA Connector DC Pin 100 Ohm Resistor, 0603 Pkg. HMC347LP3 / HMC347LP3E SPDT Switch 107521 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 213