426MS8E

HMC426MS8 / 426MS8E v00.0903 SMT SiGe MMIC DIVIDE-BY-4, DC - 4 GHz 6 FREQUENCY DIVIDERS & DETECTORS - SMT Typical Applications Prescaler for DC to 4.0 GHz PLL Applications: • DBS/CATV Tuners • 802.11x & HiperLAN WLAN • Fixed Wireless & WLL • Microwave & VSAT Radios • Cellular & 3G Features Ultra Low SSB Phase Noise: -146 dBc/Hz Wide Input Power Range: -15 to +10 dBm Output Power: +3.5 dBm Single DC Supply: +3V @ 13 mA MS8 SMT Package Functional Diagram General Description The HMC426MS8 & HMC426MS8E are low noise Divide-by-4 Static Dividers utilizing SiGe technology in 8 lead surface mount plastic packages. This device operates from DC (with a square wave input) to 4.0 GHz input frequency while operating from a single +3V supply at only 13 mA. The low additive SSB phase noise of -146 dBc/Hz at 100 kHz offset helps the user maintain excellent system noise performance. Electrical Specifi cations, TA = +25° C, 50 Ohm System, Vcc= 3V Parameter Maximum Input Frequency Minimum Input Frequency Input Power Range Sine Wave Input. [1] Fin = 0.5 to 2 GHz Fin = 2 to 4 GHz Output Power Fin = 1 GHz Fin = 4 GHz Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) 1. Divider will operate down to DC for square-wave input signal. Pin = 0 dBm, Fin = 3 GHz Pin = 0 dBm, Fout = 500 MHz -15 -15 +0.5 -3 Conditions Min. 4.0 Typ. 4.5 0.2 -20 -20 +3.5 0 25 -146 400 13 0.5 +5 +10 Max. Units GHz GHz dBm dBm dBm dBm dB dBc/Hz ps mA 6 - 60 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC426MS8 / 426MS8E v00.0903 SMT SiGe MMIC DIVIDE-BY-4, DC - 4 GHz Input Sensitivity Window, T= 25 °C 20 Input Sensitivity Window vs. Temperature 20 6 FREQUENCY DIVIDERS & DETECTORS - SMT 6 - 61 10 INPUT POWER (dBm) INPUT POWER (dBm) 10 0 Recommended Operating Window 0 -10 -10 Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C -20 -20 -30 0 1 2 INPUT FREQUENCY (GHz) 3 4 -30 0 1 2 INPUT FREQUENCY (GHz) 3 4 Output Power vs. Temperature 10 8 OUTPUT POWER (dBm) 6 4 2 0 -2 -4 -6 -8 -10 0 1 2 INPUT FREQUENCY (GHz) 3 4 +25C +85C -40C SSB Phase Noise Performance @ Fin= 3 GHz Pin= 0 dBm, T= 25 °C 0 -20 SSB PHASE NOISE (dBc/Hz) -40 -60 -80 -100 -120 -140 -160 2 10 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 °C 0 Reverse Leakage, Pin= 0 dBm, T= 25 °C 0 -10 -10 OUTPUT LEVEL (dBm) OUTPUT LEVEL (dBm) Pfeedthru 2nd Harmonic 3rd Harmonic -20 -30 -40 -50 -60 -70 -80 -20 -30 -40 -50 0 1 2 INPUT FREQUENCY (GHz) 3 4 0 1 2 INPUT FREQUENCY (GHz) 3 4 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC426MS8 / 426MS8E v00.0903 SMT SiGe MMIC DIVIDE-BY-4, DC - 4 GHz 6 FREQUENCY DIVIDERS & DETECTORS - SMT Output Voltage Waveform, Pin= 0 dBm, Fout= 500 MHz, T= 25 °C 500 400 300 Input Return Loss 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 AMPLITUDE (mV) 200 100 0 -100 -200 -300 -400 -500 24.6 25.2 25.7 26.3 TIME (nS) 26.9 27.4 28 0 1 2 INPUT FREQUENCY (GHz) 3 4 6 - 62 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC426MS8 / 426MS8E v00.0903 SMT SiGe MMIC DIVIDE-BY-4, DC - 4 GHz Absolute Maximum Ratings RF Input (Vcc = +3V) Vcc Channel Temperature Continuous Pdiss (T = 85 °C) (derate 7 mW/ °C above 85 °C) Thermal Resistance (RTH)(junction to lead) Storage Temperature Operating Temperature +13 dBm +3.5V 150 °C 460 mW 142 °C/W -65 to +150 °C -40 to +85 °C Typical Supply Current vs. Vcc Vcc (V) 2.7 3.0 3.3 Icc (mA) 10 13 16 6 FREQUENCY DIVIDERS & DETECTORS - SMT 6 - 63 Note: Divider will operate over full voltage range shown above ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC426MS8 HMC426MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H426 XXXX H426 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC426MS8 / 426MS8E v00.0903 SMT SiGe MMIC DIVIDE-BY-4, DC - 4 GHz 6 FREQUENCY DIVIDERS & DETECTORS - SMT Pin Description Pin Number 1 Function VCC Description Supply voltage 3V ± 0.3V. Interface Schematic 2 IN RF Input must be DC blocked. 3 IN RF Input 180° out of phase with pin 2 for differential operation. AC ground for single ended operation. 4, 5 GND RF/DC Ground 6, 8 N/C No connection. 7 OUT Divided output. Application Circuit 6 - 64 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC426MS8 / 426MS8E v00.0903 SMT SiGe MMIC DIVIDE-BY-4, DC - 4 GHz Evaluation PCB 6 FREQUENCY DIVIDERS & DETECTORS - SMT 6 - 65 List of Materials for Evaluation PCB 107622 [1] Item J1 - J2 J3 - J4 C1 C2 C3 - C4 C5 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 1000 pF Capacitor, 0603 Pkg. 4.7 uF Tantalum Capacitor 100 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0402 Pkg. HMC426MS8 / HMC426MS8E Divide-by-4 107620 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. This evaluation board is designed for single ended input and output testing. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com