465LP5E

HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Features Gain: 15 dB output voltage to 10vpk-pk +24 dBm saturated output power supply voltage: +8v @160 mA 8 Amplifiers - Driver & GAin Block - smT Typical Applications The Hmc465lp5(e) wideband driver is ideal for: • oc192 ln/mZ modulator Driver • microwave radio & vsAT • Test instrumentation • military eW, ecm & c i 3 50 ohm matched input/output 32 lead 5x5 mm Qfn package: 25 mm2 Functional Diagram General Description The Hmc465lp5(e) is a GaAs mmic pHemT Distributed Driver Amplifier packaged in leadless 5x5 mm surface mount package which operate between Dc and 20 GHz. The amplifier provides 15 dB of gain, 3 dB noise figure and +25 dBm of saturated output power while requiring only 160 mA from a +8v supply. Gain flatness is excellent at ±0.5 dB as well as ±4 deg deviation from linear phase from Dc - 10 GHz making the Hmc465lp5(e) ideal for oc192 fiber optic ln/mZ modulator driver amplifiers as well as test equipment applications. The Hmc465lp5(e) amplifiers i/os are internally matched to 50 ohms. Electrical Specifications, TA = +25° C, Vdd= 8V, Vgg2= 1.5V, Idd= 160 mA* parameter frequency range Gain Gain flatness Gain variation over Temperature noise figure input return loss output return loss output power for 1 dB compression (p1dB) saturated output power (psat) output Third order intercept (ip3) saturated output voltage Group Delay variation supply current (idd) (vdd= 8v, vgg1= -0.6v Typ.) 21 13 min. Typ. Dc - 6 16 ±0.75 0.015 3.0 20 22 24 25.5 32 10 ±15 160 20 0.02 12 max. min. Typ. 6.0 - 12.0 15 ±0.25 0.020 3.0 15 17 23 25 28 10 ±15 160 160 16 0.025 9.5 max. min. Typ. 12.0 - 20.0 12.5 ±1.5 0.035 4.0 8 12 20 23 24 8 0.045 max. Units GHz dB dB dB/ °c dB dB dB dBm dBm dBm vpk-pk psec mA * Adjust Vgg1 between -2 to 0V to achieve Idd= 160 mA typical. 8-1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Gain vs. Temperature 20 Gain & Return Loss 20 15 10 RESPONSE (dB) 5 0 -5 -10 -15 -20 -25 -30 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) 16 S21 S11 S22 8 +25C +85C -40C 12 8 4 0 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) Input Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) +25C +85C -40C Output Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) +25C +85C -40C Low Frequency Gain & Return Loss 25 15 RESPONSE (dB) 5 -5 -15 -25 -35 -45 0.00001 Noise Figure vs. Temperature 10 9 8 NOISE FIGURE (dB) +25C +85C -40C S21 S11 S22 7 6 5 4 3 2 1 0 0.0001 0.001 0.01 0.1 1 10 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) FREQUENCY (GHz) F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-2 Amplifiers - Driver & GAin Block - smT GAIN (dB) HMC465LP5 / 465LP5E v03.1106 v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Psat vs. Temperature 30 8 Amplifiers - Driver & GAin Block - smT P1dB vs. Temperature 30 26 P1dB (dBm) Psat (dBm) 26 22 22 +25C +85C -40C 18 +25C +85C -40C 18 14 14 10 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) 10 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) Output IP3 vs. Temperature 40 38 36 34 IP3 (dBm) 32 30 28 26 24 22 20 18 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) +25C +85C -40C Gain, Power & Output IP3 vs. Supply Voltage @ 10 GHz, Idd = 160mA Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm) 32 30 28 26 24 22 20 18 16 14 12 10 7.5 8 SUPPLY VOLTAGE (V) 8.5 Gain P1dB Psat IP3 Group Delay -200 Deviation from Linear Phase DEVIATION FROM LINEAR PHASE (deg) 10 GROUP DELAY (pSec) 6 -250 2 -300 -2 -350 -6 -400 0 1 2 3 4 5 6 7 8 9 10 FREQUENCY (GHz) -10 0 2 4 6 8 10 FREQUENCY (GHz) 8-3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Typical Supply Current vs. Vdd vdd (v) +7.5 +8.0 +8.5 idd (mA) 161 160 159 Absolute Maximum Ratings Drain Bias voltage (vdd) Gate Bias voltage (vgg1) Gate Bias current (igg1) Gate Bias voltage (vgg2) Gate Bias current (igg2) rf input power (rfin)(vdd = +8 vdc) channel Temperature continuous pdiss (T = 85 °c) (derate 24 mW/°c above 85 °c) Thermal resistance (channel to ground paddle) storage Temperature operating Temperature +9 vdc -2 to 0 vdc +3.2mA (vdd -8) vdc to +3 vdc +3.2mA +23 dBm 150 °c 1.56 W 41.5 °c/W -65 to +150 °c -40 to +85 °c 8 Amplifiers - Driver & GAin Block - smT 8-4 elecTrosTATic sensiTive Device oBserve HAnDlinG precAUTions Outline Drawing noTes: 1. leADfrAme mATeriAl: copper AlloY 2. Dimensions Are in incHes [millimeTers] 3. leAD spAcinG TolerAnce is non-cUmUlATive. 4. pAD BUrr lenGTH sHAll Be 0.15mm mAXimUm. pAD BUrr HeiGHT sHAll Be 0.05mm mAXimUm. 5. pAckAGe WArp sHAll noT eXceeD 0.05mm. 6. All GroUnD leADs AnD GroUnD pADDle mUsT Be solDereD To pcB rf GroUnD. 7. refer To HiTTiTe ApplicATion noTe for sUGGesTeD lAnD pATTern. Package Information part number Hmc465lp5 Hmc465lp5e package Body material low stress injection molded plastic roHs-compliant low stress injection molded plastic lead finish sn/pb solder 100% matte sn msl rating msl1 msl1 [1] package marking [3] H465 XXXX H465 XXXX [2] [1] max peak reflow temperature of 235 °c [2] max peak reflow temperature of 260 °c [3] 4-Digit lot number XXXX F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz 8 Amplifiers - Driver & GAin Block - smT Pin Descriptions pin number 1, 3, 4, 6 - 12, 14, 17, 18, 19, 20, 22 - 28, 31, 32 function n/c Description The pins are not connected internally; however, all data shown herein was measured with these pins connected to rf/Dc ground externally. Gate control 2 for amplifier. +1.5v should be applied to vgg2 for nominal operation. interface schematic 2 vgg2 5 rfin This pad is Dc coupled and matched to 50 ohms. 13 vgg1 Gate control 1 for amplifier. 15 AcG4 low frequency termination. Attach bypass capacitor per application circuit herein. 16 AcG3 21 rfoUT & vdd rf output for amplifier. connect the Dc bias (vdd) network to provide drain current (idd). see application circuit herein. low frequency termination. Attach bypass capacitor per application circuit herein. 29 30 Ground paddle AcG2 AcG1 GnD Ground paddle must be connected to rf/Dc ground. Application Circuit NOTE 1: Drain Bias (Vdd) must be applied through a broadband bias tee or external bias network. 8-5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Evaluation PCB 8 Amplifiers - Driver & GAin Block - smT 8-6 List of Materials for Evaluation PCB 108347 item J1 - J2 J3 - J4 c1, c2 c3 - c6 c7 - c9 U1 pcB [2] Description sri k connector 2mm molex Header 100 pf capacitor, 0402 pkg. 1000 pf capacitor, 0603 pkg. 4.7 µf capacitor, Tantalum Hmc465lp5 / Hmc465lp5e 109765 evaluation pcB [1] [1] reference this number when ordering complete evaluation pcB [2] circuit Board material: rogers 4350 The circuit board used in the final application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and package bottom should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz 8 Amplifiers - Driver & GAin Block - smT 8-7 Device Operation These devices are susceptible to damage from electrostatic Discharge. proper precautions should be observed during handling, assembly and test. The input to this device should be Ac-coupled. To provide the typical 8vp-p output voltage swing, a 1.2vp-p Accoupled input voltage swing is required. Device Power Up Instructions 1. Ground the device 2. set vgg to -2v (no drain current) 3. set vctl to +1v (no drain current) 4. set vdd to +5v (no drain current) 5. Adjust vgg for idd = 140mA • vgg may be varied between -1v and 0v to provide the desired eye crossing point percentage (i.e. 50% crosspoint) and a limited cross point control capability. • vdd may be increased to +7v if required to achieve greater output voltage swing. • vctl may be adjusted between +2v and +0v to vary the output voltage swing. Device Power Down Instructions 1. reverse the sequence identified above in steps 1 through 4. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC465LP5 / 465LP5E v06.1210 GaAs PHEMT MMIC MODULATOR DRIVER AMPLIFIER, DC - 20 GHz Notes: 8 Amplifiers - Driver & GAin Block - smT F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-8