497LP4E

HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Typical Applications The HMC497LP4(E) is ideal for: • UMTS, GSM or CDMA Basestations • Fixed Wireless or WLL • ISM Transceivers, 900 & 2400 MHz • GMSK, QPSK, QAM, SSB Modulators Features Very Low Noise Floor: -161 dBm/Hz Very High Linearity: +22 dBm OIP3 High Output Power: +9 dBm Output P1dB High Modulation Accuracy DC - 700 MHz Baseband Input 10 MODULATORS - DIRECT QUADRATURE - SMT Functional Diagram General Description The HMC497LP4(E) is a low noise high linearity Direct Quadrature Modulator RFIC which is ideal for digital modulation applications from 100 - 4000 MHz including; Cellular/3G, Broadband Wireless Access & ISM circuits. Housed in a compact 4x4 mm (LP4) SMT QFN package, the RFIC requires minimal external components & provides a low cost alternative to more complicated double upconversion architectures. The RF output port is single-ended and matched to 50 Ohms with no external components. The LO requires -6 to +6 dBm and can be driven in either differential or single-ended mode while the baseband inputs will support modulation inputs from DC - 700 MHz typical. This device is optimized for a supply voltage of +4.5V to +5.5V and consumes 170 mA @ +5V supply. Electrical Specifi cations, See Test Conditions on following page herein. Parameter Frequency Range, RF Output P1dB Output Noise Floor Output IP3 Output Power Carrier Feedthrough (uncalibrated) Sideband Suppression (uncalibrated) LO Port Return Loss RF Port Return Loss +4 Min. Typ. 450 - 960 +8 -161 +22 +6 -38 43 25 11 +3 Max. Min. Typ. 1700 - 2200 +8 -159 +22 +5 -36 42 15 20 +2 Max. Min. Typ. Max. Min. Typ. Max. Units MHz dBm dBm/Hz dBm dBm dBm dBc dB dB 2200 - 2700 +7 -157 +20 +5 -32 33 14 17 0 3400 - 4000 +6 -150 +17 +3 -30 22 13 11 10 - 24 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Electrical Specifi cations, (continued) Parameter RF Output RF Frequency Range RF Return Loss LO Input LO Frequency Range LO Input Power LO Port Return Loss Baseband Input Port Baseband Port Bandwidth Baseband Input DC Voltage (Vbbdc) Baseband Input DC Bias Current (Ibbdc) Single-ended Baseband Input Capacitance DC Power Requirements Supply Voltage (Vcc1, Vcc2) Supply Current (Icc1, Icc2) Single-ended. De-embed to the lead of the device. See Test Conditions Below +4.5 +5.0 168 +5.5 V mA 3 dB Bandwidth with 50 Ω source. DC +1.4 +1.5 90 4.5 700 +1.6 MHz V μA 100 -6 0 15 4000 +6 MHz dBm dB 100 15 4000 MHz dB Conditions Min. Typ. Max. Units 10 MODULATORS - DIRECT QUADRATURE - SMT 10 - 25 pF Test Conditions: Unless Otherwise Specifi ed, the Following Test Conditions Were Used Parameter Temperature Baseband Input Frequency Baseband Input DC Voltage (Vbbdc) Baseband Input AC Voltage Baseband Input AC Voltage for OIP3 Measurement Frequency Offset for Output Noise Measurements Supply (Vcc1, Vcc2) LO Input Power LO Input Mode Mounting Configuration Sideband & Carrier Feedthrough (Peak to Peak Differential, I and Q) (Peak to Peak Differential, I and Q) Condition +25 °C 200 kHz +1.5V 1.6V 800 mV per tone @ 150 & 250 kHz 20 MHz +5.0V 0 dBm Single-Ended through LON Refer to HMC497LP4 Application Schematic Herein Uncalibrated Calibrated vs. Uncalibrated Test Results During the Uncalibrated Sideband and Carrier Suppression tests, care is taken to ensure that the I/Q signal paths from the Vector Signal Generator (VSG) to the Device Under Test (DUT) are equal. The “Uncalibrated, +25 °C” Sideband and Carrier Suppression plots were measured at room temperature, while the “Uncalibrated, over Temperature” Sideband and Carrier Suppression plots represent the worst case uncalibrated suppression levels measured at T= -40 °C, +25 °C, and +85 °C. The “Calibrated, + 25 °C” Sideband Suppression data was plotted after a manual adjustment of the I/Q amplitude balance and I/Q phase offset (skew) at +25 °C, and at each LO input power level. The +25 °C adjustment settings were held constant during tests over temperature. The “Calibrated, over Temperature” plots represent the worst case calibrated Sideband Suppression levels at T= -40 °C, +25 °C, and +85 °C. The “Calibrated, +25 °C” Carrier Suppression data was plotted after a manual adjustment of the Ip/In & Qp/Qn DC offsets at +25 °C, and at each LO input power level. The +25 °C adjustment settings were held constant during tests over temperature. The “Calibrated, over Temperature” plots represent the worst case Carrier Suppression levels measured at T= -40 °C, +25 °C, and +85 °C. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Output IP3, P1dB & Noise Floor @ 20 MHz Offset vs. Frequency OUTPUT P1dB (dBm), OUTPUT IP3 (dBm) 30 OUTPUT IP3 20 -130 OUTPUT NOISE FLOOR @ 20 MHz (dBm/Hz) -120 Wideband Performance vs. Frequency 10 OUTPUT POWER (dBm) 5 10 OUTPUT P1dB -140 0 +25C +85C -40C 0 +25C +85C -40C -150 -5 -10 NOISE FLOOR -20 0 400 -160 SET-UP NOISE FLOOR -170 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) 10 MODULATORS - DIRECT QUADRATURE - SMT -10 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) Uncalibrated Carrier Feedthrough [1] vs. Frequency 10 CARRIER FEEDTHROUGH (dBm) 0 -10 -20 -30 -40 -50 -60 -70 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) +25C +85C -40C Calibrated Carrier Feedthrough [1] vs. Frequency 10 CARRIER FEEDTHROUGH (dBm) 0 -10 -20 -30 -40 -50 -60 -70 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) +25C +85C -40C Sideband Suppression vs. Frequency 10 SIDEBAND SUPPRESSION (dBc) 0 +25C +85C -40C Return Loss vs. Frequency 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 RF LO -10 -20 -30 -40 -50 -60 -70 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) [1] See note titled “Calibrated vs. Uncalibrated test results” herein. 10 - 26 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Wideband Performance vs. Frequency Over LO Power [3] 10 OUTPUT POWER OUTPUT POWER (dBm) 5 -15 0 SIDEBAND SUPPRESSION (dBc) Output IP3, P1dB & Noise Floor @ 20 MHz Offset vs. Frequency Over LO Power [3] OUTPUT P1dB (dBm), OUTPUT IP3 (dBm) 30 OUTPUT IP3 20 -130 OUTPUT P1dB OUTPUT NOISE FLOOR @ 20 MHz (dBm/Hz) -120 10 -140 0 SIDEBAND SUPPRESSION -5 -30 0 NOISE FLOOR -10 -150 -45 -160 SET-UP NOISE FLOOR -170 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) -10 0 400 -60 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) -20 0 400 10 MODULATORS - DIRECT QUADRATURE - SMT 10 - 27 Uncalibrated Carrier Feedthrough [2] vs. Frequency 10 CARRIER FEEDTHROUGH (dBm) 0 -10 -20 -30 -40 -50 -60 -70 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) -6 dBm 0 dBm +6 dBm Calibrated Carrier Feedthrough [2] vs. Frequency 10 CARRIER FEEDTHROUGH (dBm) 0 -10 -20 -30 -40 -50 -60 -70 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) -6 dBm 0 dBm +6 dBm Wideband Performance vs. Frequency Over Supply Voltage [1] 10 OUTPUT POWER OUTPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 0 SIDEBAND SUPPRESSION -5 -30 -35 -40 -45 -50 -55 -10 0 400 -60 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (MHz) SIDEBAND SUPPRESSION (dBc) Output IP3, P1dB & Noise Floor @ 20 MHz vs. Offset Frequency Over Supply Voltage [1] OUTPUT P1dB (dBm), OUTPUT IP3 (dBm) 30 OUTPUT IP3 -120 OUTPUT NOISE FLOOR (dBm/Hz) 20 -130 10 OUTPUT P1dB -140 0 NOISE FLOOR -150 -10 MEASUREMENT NOISE FLOOR -160 -20 0 400 -170 800 1200 1600 2000 2400 2800 3200 3600 4000 FREQUENCY (GHz) [1] See note titled “Calibrated vs. Uncalibrated test results” herein. [2] Supply voltage from +4.5 to +5.5V. [3] LO Power from -6 dBm to +6 dBm For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz ACPR & Output Noise for W-CDMA @ 2140 MHz -60 OUTPUT NOISE @ 20 MHz Offset (dBm/Hz) -130 2 Carrier ACPR -65 ACPR (dBc) -140 Output Noise @ 20 MHz Offset vs. LO Power Over Temperature -140 OUTPUT NOISE @20 MHz (dBm/Hz) -145 RF Power +5 dBm T=+25C T=+85C T= -40C -150 -70 1 Carrier ACPR 1 Carrier NF -150 -155 -75 2 Carrier NF -160 -160 10 MODULATORS - DIRECT QUADRATURE - SMT -80 -30 -27 -24 -21 -18 -15 -12 -9 -6 -3 0 -170 -165 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 CARRIER OUTPUT POWER (dBm) LO POWER (dBm) Compression Characteristic @ 2140 MHz 10 0 Power & Linearity @ 2140 MHz vs. Baseband Voltage 10 9 OUTPUT POWER (dBm) 8 7 6 5 4 3 2 1 5 OUTPUT POWER 10 15 OIP3 (dBm) OUTPUT IP3 20 25 POWER (dBm) -10 -20 -30 -40 -50 0.8 2 TONES OUTPUT POWER (dBm) 3rd ORDER INTERMOD (dBm) 0 0 0.9 1 2 INPUT BASEBAND VOLTAGE (Vp-p diff) 0.9 1 2 0.8 INPUT BASEBAND VOLTAGE PER TONE (Vp-p diff) Single Tone Single Tone EVM vs. LO Harmonic Level & Sideband Rejection for EDGE @ 900 MHz 1200 1100 1000 EVM (m%rms) 900 800 700 -16 dBc LO 2 nd EVM vs. LO Harmonic Level & Sideband Rejection for EDGE @ 1900 MHz 2000 1800 SBR: -40 dBc 2 1600 EVM (m%rms) 1400 1200 1000 800 LO 3 Harmonic Level -70 dBc -30 dBc SBR: -42 dBc 2 rd Harmonic Level -30 dBc 600 500 400 -70 SBR: -48 dBc 2 SBR: -48 dBc 2 600 -65 -60 -55 rd -50 -45 -40 -35 -30 -30 -25 -20 nd -15 -10 -5 LO 3 Harmonic Level (dBc) LO 2 Harmonic Level (dBc) Note 1: W-CDMA (Modulation Set-up for ACPR Mode); The Baseband I and Q input signals were generated using “Test Model 1 with 64 channels” settings in the Agilent E3844C. Note 2: The I/Q baseband amplitude and phase inputs were offset to achieve Sideband Rejection (SBR) levels. LO = +6 dBm, SSB Power = 0 dBm 10 - 28 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Absolute Maximum Ratings Vcc1, Vcc2 LO Input Power Baseband Input Voltage (AC + DC) (Reference to GND) Channel Temperature Continuous Pdiss (T = 85°C) (Derate 30 mW/°C above 85°C) Thermal Resistance (Rth) (junction to lead) Storage Temperature Operating Temperature ESD Sensitivity (HBM) 0V to +6V +18 dBm 0.0V to +2.8V 150 °C 1.8 Watts 34 °C/W -65 to +150 °C -40 to +85 °C Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 10 MODULATORS - DIRECT QUADRATURE - SMT 10 - 29 Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number HMC497LP4 HMC497LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H497 XXXX H497 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Pin Descriptions Pin Number 1,6, 7, 13, 15 2, 5, 8, 11, 12, 14, 17, 19, 20, 23 Function N/C Description Not connected. These pins and the ground paddle should be connected to a high quality RF/DC ground. Interface Schematic GND 10 MODULATORS - DIRECT QUADRATURE - SMT 3, 4 LOP, LON LO inputs. Need DC decoupling capacitors. The ports could be driven single ended or differentially. 9, 10 QN, QP Q channel differential baseband input. These high impedance ports should be biased around 1.5V DC. Nominal recommended baseband input is around 1.6V pp differential. 16 RFOUT RF output. 50 Ohms. Needs DC blocking capacitor. 18 Vcc1 Supply voltage for the mixer and output stages 79mA @ +5.0V. 21, 22 IP, IN I channel differential baseband input. These high impedance ports should be at the same bias voltage (VbbDC) as Qn & Qp. 24 Vcc2 Supply voltage for the LO stage 88mA @ +5V. 10 - 30 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v04.1108 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Evaluation PCB 10 MODULATORS - DIRECT QUADRATURE - SMT 10 - 31 List of Materials for Evaluation PCB 108962 [1] Item J1 - J7 J8, J9 C1 - C3 C4, C5 C6, C7 U1 PCB [2] Description PC Mount SMA Connector DC Molex Connector 100 pF Chip Capacitor, 0402 Pkg. 1000 pF Chip Capacitor, 0402 Pkg. 4.7 uF, Case A, Tantulum HMC497LP4 Modulator 108960 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v03.0307 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Application & Evaluation PCB Schematic 10 MODULATORS - DIRECT QUADRATURE - SMT Characterization Set-up 10 - 32 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC497LP4 / 497LP4E v03.0307 SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz Notes: 10 MODULATORS - DIRECT QUADRATURE - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 33