HMC-C008_10

HMC-C008 v05.1007 1 AMPLIFIERS Features P1dB Output Power: 15 Watts from 1.8 to 2.2 GHz Gain: 40 dB min Noise Figure: 6 dB Thermally Compensated and Protected Reverse Polarity Protected TTL DC Power Enable Unconditionally Stable Heat Sink/Fan Accessories Available w r Ne o ed f d men Typical Applications om Rec Test applications for: Not • Cellular/PCS/3G Infrastructure • Automated Test Equipment (ATE) • Laboratory Use ED U IN NT T O SC DUC DI RO P s sign De Functional Diagram 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz General Description The HMC-C008 is a 15 Watt Power Amplifier Module suitable for Cellular/3G repeaters, laboratory use and ATE applications. The unit includes DC power sequencing, enable and conditioning, as well as an output circulator for load mismatch protection. Thermal protection/fault circuitry automatically turns off DC power at base temperatures exceeding +75 °C and restores power at < +55 °C. Electrical Specifi cations, TA = +25° C, VIN = +12V Parameter Frequency Range Gain Noise Figure Input Return Loss Output Return Loss Output Power for 1 dB Compression (P1dB) Saturated Output Power (Psat) Output Third Order Intercept (IP3) (Two-tone Input Power = -28 dBm each tone) Channel Output Power for -50 dBc ACPR (CDMA 2000, 1960 MHz) Channel Output Power for -50 dBc ACPR (W-CDMA, 2110 MHz) Second Harmonic at Output P1dB Third Harmonic at Output P1dB Spurious at Output P1dB Supply Current 15 43 52 36 33 -55 -55 -65 6.5 7.0 40 Min. Typ. 1.8 - 2.2 42 6 12 12 8 Max. Units GHz dB dB dB dB W dBm dBm dBm dBm dBc dBc dBc A 1-1 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C008 v05.1007 Gain vs. Temperature 45 44 43 42 GAIN (dB) 41 40 39 38 37 36 35 1.7 1.8 ED U IN NT T O SC DUC DI RO P Input & Output Return Loss 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz 1 AMPLIFIERS 2.3 1.9 2 FREQUENCY (GHz) w r Ne o ed f d men om Rec Not 2.1 2.2 2.3 -40 1.7 1.8 1.9 +25C +50C 0C s sign De INPUT OUTPUT 2 2.1 2.2 FREQUENCY (GHz) P1dB vs. Temperature 46 44 42 P1dB (dBm) Psat vs. Temperature 46 44 42 Psat (dBm) 40 38 36 34 32 30 1.7 +25C +50C 0C 40 38 36 34 32 30 1.7 +25C +50C 0C 1.8 1.9 2 2.1 2.2 2.3 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) FREQUENCY (GHz) ACPR @ 2110 MHz, W-CDMA -20 -25 -30 -35 ACPR (dBc) -40 -45 -50 -55 -60 -65 -70 22 24 26 28 30 32 34 36 38 40 CHANNEL OUTPUT POWER (dBm) WCDMA Frequency : 2.11 GHz Integration BW: 3.84 MHz 64 DPCH ACPR @ 1960 MHz, CDMA-2000 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 -85 22 CDMA2000 Rev. 8 Frequency : 1.96 GHz Integration BW: 1.228 MHz Forward Link, SRI, 9 CHANNELS ACPR (dBc) 24 26 28 30 32 34 36 38 40 CHANNEL OUTPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-2 HMC-C008 v05.1007 1 AMPLIFIERS Output IP3 vs. Temperature 60 58 56 IP3 (dB) 54 52 50 48 46 1.7 1.8 ED U IN NT T O SC DUC DI RO P Reverse Isolation vs. Temperature 0 -10 -20 -30 -40 -50 -60 ISOLATION (dB) +25C +50C 0C 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz 1.9 2 FREQUENCY (GHz) w r Ne o ed f d men om Rec Not +25C +50C 0C s sign De 2 2.1 2.1 2.2 2.3 -70 1.7 1.8 1.9 2.2 2.3 FREQUENCY (GHz) Noise Figure vs. Temperature 10 9 8 NOISE FIGURE (dB) 7 6 5 4 3 2 1 0 1.7 1.8 1.9 2 2.1 2.2 2.3 +25C +50C 0C Absolute Maximum Ratings Supply Voltage (VIN) RF Input Power (RFIN) Storage Temperature Operating Temperature RF Output Isolator Max Dissipation Thermal Fault Indicator Max Pdiss (derate 1.8 mW/°C above 50 °C) Enable Vmax +13 Vdc +10 dBm -40 to +70 °C 0 to +50 °C 20 W 180 mW 6V FREQUENCY (GHz) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Thermal Fault Indicator Characteristics Parameter IOUT (VOUT > 2V) RON (I OUT = 50 mA) ROFF (VOUT = 30 V) 1 Min. Typ. 350 7.5 Max. Units mA Ohms MOhm Enable Input Characteristics Parameter VIH VIL IIL @ VIN = 0V IIH @ 5V Min. 3.5 1.6 -0.5 < ± 50 Typ. Max. Units V V mA μA Recommended Biasing Procedure TURN-ON 1. Connect RF input and output 2. Apply Supply Voltage VIN (+12 Vdc) 3. Set Enable low 4. Apply RF input signal TURN-OFF 1. Remove RF input signal 2. Remove Supply Voltage VIN 1-3 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C008 v05.1007 Pin Descriptions Pin Number 1 2 3 ED U IN NT T O SC DUC DI RO P Function Description Interface Schematic RFIN & RF Ground RF input connector, SMA female. This pin is AC coupled and matched to 50 Ohms. VIN GND RFOUT & RF Ground 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz 1 AMPLIFIERS 1-4 4 w r Ne o ed f d men om Rec Not Power supply voltage for the amplifier. Power supply ground. RF output connector, SMA female. This pin is isolator protected and matched to 50 Ohms. Ground for thermal fault indicator and enable circuit. s sign De 5 GND 6 Thermal Fault Indicator Open drain output. High impedance for base plate temperatures less than 55 °C. Low impedance for base plate temperatures exceeding 75 °C. TTL compatible supply voltage (VIN) shutdown. If enable feature is not required, short this pin to DC ground. 7 Enable TTL “High” Disable TTL “Low” Enable For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C008 v05.1007 1 AMPLIFIERS Outline Drawing ED U IN NT T O SC DUC DI RO P w r Ne o ed f d men om Rec Not s sign De 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz Package Information Package Type Package Weight [1] C-7 740 gms [2] N/A Spacer Weight [1] Includes the connectors [2] ±10% Tolerance NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH a. COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 b. BASE, TIN 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X±.1 (2.54mm) .XX±.02 (0.50mm) 6. BASE MUST BE GROUNDED AND MOUNTED TO HEAT SINK CAPABLE OF DISSIPATING 100W (50 °C) 1-5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C008 v05.1007 HMC-C008 Heatsink/Fan Outline Drawing ED U IN NT T O SC DUC DI RO P w r Ne o ed f d men om Rec Not s sign De 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz 1 AMPLIFIERS 1-6 NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH: COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X±.1 (2.54mm) .XX±.02 (0.50mm) HMC-C008 Ordering Information Part Number HMC-C008 HMC-C008HV115 HMC-C008HV230 Description 15 Watt Power Amplifier Module, 1.8 - 2.2 GHz 15 Watt Power Amplifier Module with heat sink, 115 Vac fan and power cord. 15 Watt Power Amplifier Module with heat sink, 230 Vac fan and power cord. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com