HMC204_09

HMC204 v04.0907 GaAs MMIC PASSIVE FREQUENCY DOUBLER, 4 - 8 GHz INPUT Typical Applications Features Conversion Loss: 17 dB Fo, 3Fo, 4Fo Isolation: 38 dB Passive: No Bias Required 2 FREQUENCY MULTIPLIERS - PASSIVE - CHIP The HMC204 is suitable for: • Wireless Local Loop • LMDS, VSAT, and Point-to-Point Radios • Test Equipment Functional Diagram General Description The HMC204 is a passive miniature frequency doubler in a MMIC die. Suppression of undesired fundamental and higher order harmonics is 38 dB typical with respect to input signal level. The doubler utilizes the same GaAs Schottky diode/balun technology found in Hittite MMIC mixers. It features small size, no DC bias, and no measurable additive phase noise onto the multiplied signal. Electrical Specifi cations, TA = +25° C, As a Function of Drive Level Input = +10 dBm Parameter Frequency Range, Input Frequency Range, Output Conversion Loss FO Isolation (with respect to input level) 3FO Isolation (with respect to input level) 4FO Isolation (with respect to input level) Min. Typ. 5.5 - 7.5 11.0 - 15.0 17 20 41 42 35 Max. Min. Input = +12 dBm Typ. 5.0 - 8.0 10.0 - 16.0 17 45 46 38 20 Max. Min. Input = +15 dBm Typ. 4.0 - 8.0 8.0 - 16.0 18 21 Max. Units GHz GHz dB dB dB dB 2 - 10 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC204 v04.0907 GaAs MMIC PASSIVE FREQUENCY DOUBLER, 4 - 8 GHz INPUT Conversion Gain vs Temperature @ +15 dBm Drive Level 0 -5 CONVERSION GAIN (dB) -10 ISOLATION (dB) -15 -20 -25 -30 -35 -40 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) +25 C -55 C +85 C Isolation @ +15 dBm Drive Level* 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 0 5 10 15 20 25 30 35 FREQUENCY (GHz) Fo 3Fo 4Fo 2 FREQUENCY MULTIPLIERS - PASSIVE - CHIP 2 - 11 *With respect to input level Input Return Loss vs. Drive Level 0 Output Return Loss for Several Input Frequencies 0 RETURN LOSS (dB) -10 RETURN LOSS (dB) -5 -5 -10 -15 Pin = + 8 dBm Pin = +10 dBm Pin = +12 dBm Pin = +14 dBm -15 4 GHz In 6 GHz In 8 GHz In -20 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) -20 8 10 12 14 16 OUTPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC204 v04.0907 GaAs MMIC PASSIVE FREQUENCY DOUBLER, 4 - 8 GHz INPUT Conversion Gain @ 25°C vs. Drive Level Output Return Loss with 4 GHz Input 0 2 CONVERSION GAIN (dB) 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 -40 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) +10 dBm +12 dBm +15 dBm +8 dBm -5 FREQUENCY MULTIPLIERS - PASSIVE - CHIP -10 -15 +8 dBm +10 dBm +12 dBm -20 8 10 12 14 16 OUTPUT FREQUENCY (GHz) Conversion Gain @ -55°C vs. Drive Level 0 -5 CONVERSION GAIN (dB) Output Return Loss with 6 GHz Input 0 +8 dBm +10 dBm +12 dBm -15 -20 -25 -30 -35 -40 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) +8 dBm +10 dBm +12 dBm +15 dBm RETURN LOSS (dB) -10 -5 -10 -15 -20 8 10 12 14 16 OUTPUT FREQUENCY (GHz) Conversion Gain @ +85°C vs. Drive Level 0 -5 CONVERSION GAIN (dB) Output Return Loss with 8 GHz Input 0 +8 dBm +12 dBm +10 dBm -15 -20 -25 -30 -35 -40 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) +8 dBm +10 dBm +12 dBm +15 dBm RETURN LOSS (dB) -10 -5 -10 -15 -20 8 10 12 14 16 OUTPUT FREQUENCY (GHz) 2 - 12 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC204 v04.0907 GaAs MMIC PASSIVE FREQUENCY DOUBLER, 4 - 8 GHz INPUT Absolute Maximum Ratings Input Drive Storage Temperature Operating Temperature +27 dBm -65 to +150 °C -55 to +85 °C 2 FREQUENCY MULTIPLIERS - PASSIVE - CHIP NOTES: 1. DIE THICKNESS IS 0.100 [0.004], BACKSIDE IS GROUND 2. BOND PADS ARE 0.100 [0.004] SQUARE 3. BOND PAD SPACING, CTR-CTR: 0.150 [0.006] 4. ALL DIMENSION IN INCHES [MILLIMETERS] 5. ALL TOLERANCES ARE ±0.025 [±0.001] 6. BOND PAD METALLIZATION: GOLD 7. BACKSIDE METALLIZATION: GOLD ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Die Packaging Information [1] Standard WP-2 (Waffle Pack) Alternate [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 2 - 13 HMC204 v04.0907 GaAs MMIC PASSIVE FREQUENCY DOUBLER, 4 - 8 GHz INPUT Pad Description 2 FREQUENCY MULTIPLIERS - PASSIVE - CHIP Pad Number Function Description Interface Schematic 1 RFIN Pad is DC coupled and matched to 50 Ohms. 2 RFOUT Pad is AC coupled and matched to 50 Ohms. Die Bottom GND Die bottom must be connected to RF/DC ground. 2 - 14 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC204 v04.0907 GaAs MMIC PASSIVE FREQUENCY DOUBLER, 4 - 8 GHz INPUT Handling Precautions Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: Follow ESD precautions to protect against ESD strikes. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip may have fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. 2 FREQUENCY MULTIPLIERS - PASSIVE - CHIP 2 - 15 Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding Ball or wedge bond with 1.0 diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package. RF bonds should be as short as possible. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com