HMC215LP4E

www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Features Input IP3: +25 dBm Low Input LO Drive: +2 to +6 dBm High LO to RF Isolation: 32 dB Low Conversion Loss: 8 dB Single Positive Supply: +5V @ 56 mA RoHS Compliant 4x4 mm QFN Package Typical Applications The HMC215LP4 / HMC215LP4E is ideal for Wireless Infrastructure Applications: • PCS / 3G Infrastructure • Base Stations & Repeaters 8 MIXERS - SMT • WiMAX & WiBro • ISM & Fixed Wireless Functional Diagram General Description The HMC215LP4 & HMC215LP4E are high linearity, double-balanced converter ICs that operate from 1.7 to 4.0 GHz and deliver a +25 dBm input third order intercept point. The LO amplifier output and high dynamic range mixer input are positioned so that an external LO filter can be placed in series between them. The converter provides 32 dB of LO to RF isolation and is ideal for upconverter and downconverter applications. The IC operates from a single +5V supply consuming 56 mA of current and accepts a LO drive level of 2 to 6 dBm. The design requires no external baluns and supports IF frequencies between DC and 1 GHz. The HMC215LP4(E) is pin for pin compatible with the HMC552LP4(E), which operates from 1.6 to 3.0 GHz. Electrical Specifications, TA = +25°C, LO = +4 dBm, Vcc = +5V, IF = 100 MHz* Parameter Frequency Range, RF, LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Compression (Input) LO Drive Input Level (Typical) Supply Current (Icc) 23 10 Min. Typ. 1.7 - 4.0 DC - 1.0 8.0 8.5 32 20 25 17 2 to 6 56 70 11 Max. Units GHz GHz dB dB dB dB dBm dBm dBm mA *Unless otherwise noted, all measurements performed as a downconverter, with low side LO and configured as shown in application circuit. 8 - 78 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Conversion Gain vs. Temperature 0 Isolation 0 RF to IF LO to RF LO to IF CONVERSION GAIN (dB) -10 -5 ISOLATION (dB) -20 -10 -30 -15 +25C +85C -40C 8 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -40 -20 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -50 Conversion Gain vs. LO Drive 0 Return Loss 0 CONVERSION GAIN (dB) -10 RETURN LOSS (dB) -5 -5 RF LO -10 -15 LO= 0 dBm LO= +2 dBm LO= +4 dBm LO= +6 dBm LO= +8 dBm -15 -20 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -20 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) Upconverter Performance Conversion Gain vs. LO Drive 0 IF Bandwidth 0 CONVERSION GAIN (dB) -5 -5 RESPONSE (dB) -10 -10 -15 -15 LO= 0 dBm LO= +2 dBm LO= +4 dBm LO= +6 dBm -20 Conversion Gain Return Loss -20 1 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) -25 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 79 MIXERS - SMT www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Input IP3 vs. Temperature 40 35 INPUT IP3 (dBm) Input IP3 vs. LO Drive 35 30 INPUT IP3 (dBm) 25 20 15 10 5 1.5 30 25 20 15 10 8 MIXERS - SMT +25C +85C -40C LO= 0 dBm LO= +2 dBm LO= +4 dBm LO= +6 dBm 5 1.5 2 2.5 3 3.5 4 4.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) FREQUENCY (GHz) Input IP2 vs. Temperature 80 70 INPUT IP2 (dBm) 60 50 40 30 20 1.5 +25C +85C -40C Input IP2 vs. LO Drive 80 70 INPUT IP2 (dBm) 60 50 40 30 20 1.5 LO= 0 dBm LO= +2 dBm LO= +4 dBm LO= +6 dBm 2 2.5 3 3.5 4 4.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) FREQUENCY (GHz) Input P1dB vs. Temperature 20 19 18 INPUT P1dB (dBm) 17 16 15 14 13 12 11 10 1.5 1.8 2 2.2 2.5 2.7 3 3.2 3.5 3.7 4 4.2 +25C +85C -40C FREQUENCY (GHz) 8 - 80 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz MxN Spurious @ IF Port nLO mRF 0 1 2 3 4 0 xx 5 78 83 103 1 -4 0 66 97 101 2 10 22 60 92 106 3 14 37 63 80 105 4 32 49 93 80 101 Harmonics of LO nLO Spur @ RF Port LO Freq. (GHz) 1.0 1.4 1.8 2.2 2.6 3.0 1 32 28 29 33 35 34 2 40 19 16 18 23 20 3 27 25 30 27 34 41 4 40 30 42 44 41 44 8 MIXERS - SMT 8 - 81 RF Freq. = 1.9 GHz @ -10 dBm LO Freq. = 1.8 GHz @ 4 dBm All values in dBc relative to the IF power level. LO = 4 dBm All values in dBc below input LO level measured at RF port. Typical Supply Current Vcc +5.0 Icc (mA) 56 mA For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Absolute Maximum Ratings RF / IF Input (Vcc= +5V) LO Drive (Vcc= +5V) BIAS Junction Temperature Continuous Pdiss (T = 85°C) (derate 5.21 mW/°C above 85°C) Thermal Resistance (junction to ground paddle) Storage Temperature +22 dBm +10 dBm +7 Vdc 150°C 0.339 W 192 °C/W -65 to +150°C -40 to +85°C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 8 MIXERS - SMT Operating Temperature Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC215LP4 HMC215LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H215 XXXX H215 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 8 - 82 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Pin Descriptions Pin Number Function Description Interface Schematic 1 MIX LO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. 2, 6 - 9, 11 - 17, 19 - 24 N/C No connection. These pins may be connected to RF ground. Performance will not be affected. 8 MIXERS - SMT 8 - 83 3 BIAS Power supply for the LO amplifier. Three external bypass capacitors are recommended for optimum performance, as illustrated in the application circuit. 4 GND Backside of package has exposed metal ground paddle that must also be connected to ground. 5 LO This pin is DC coupled and matched to 50 Ohms from 1.7 to 4.0 GHz. An off chip DC blocking capacitor is required. 10 IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 18 mA of current or die non-function and possible die failure will result. 18 RF This pin is DC coupled and matched to 50 Ohms. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Evaluation PCB 8 MIXERS - SMT List of Materials for Evaluation PCB 115820 [1] Item J1 - J3 J4, J5 C1, C2, C5 C3 C4 L1 R1 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 pF Chip Capacitor, 0402 Pkg. 1000 pF Chip Capacitor, 0603 Pkg. 2.2 μF Capacitor, Tantalum 18 nH Chip Inductor, 0603 Pkg. 18 Ohm Resistor, 1210 1/8 watt Pkg. HMC215LP4 / HMC215LP4E 113417 Evaluation Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 8 - 84 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com www.DataSheet4U.com HMC215LP4 / 215LP4E v00.0906 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.7 - 4.0 GHz Application Circuit 8 MIXERS - SMT 8 - 85 Recommended Components Values (IF = DC - 300 MHz) C3 C4 C1, C2, C5 L1 R1 1000 pF 2.2 μF 100 pF 18 nH 18 Ohm For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com