HMC232LP4_10

HMC232LP4 / 232LP4E v04.0110 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Features Isolation: 60 dB @ 3 GHz 52 dB @ 6 GHz Input P1dB: +27 dBm Insertion Loss: 1.5 dB Typical @ 6 GHz Non-Reflective Design 24 Lead 4x4mm QFN Package: 16mm2 Included in the HMC-DK005 Designer’s Kit Typical Applications The HMC232LP4(E) is ideal for: • Telecom Infrastructure • Microwave Radio & VSAT • Military Radios, Radar & ECM • Test Instrumentation Functional Diagram General Description The HMC232LP4(E) is a broadband high isolation non-reflective GaAs MESFET SPDT switch in a low cost leadless QFN surface mount plastic package. Covering DC to 12 GHz, the switch features >60 dB isolation up to 3 GHz and >42 dB isolation up to 12 GHz. Input P1dB compression is +27 dBm typical, while input IP3 is +50 dBm. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply. 11 SWITCHES - SPDT - SMT Electrical Specifi cations, TA = +25° C, With 0/-5V Control, 50 Ohm System Parameter Frequency DC - 3.0 GHz DC - 6.0 GHz DC - 9.0 GHz DC - 12.0 GHz DC - 3.0 GHz DC - 6.0 GHz DC - 9.0 GHz DC - 12.0 GHz “On State” DC - 6.0 GHz DC - 9.0 GHz DC - 12.0 GHz DC - 12.0 GHz 0.5 - 12.0 GHz 0.5 - 12.0 GHz DC - 12.0 GHz 3 6 ns ns 24 45 55 47 40 37 Min. Typ. 1.4 1.5 2.0 2.7 60 52 45 42 18 16 11 14 27 50 Max. 1.7 1.8 2.3 3.1 Units dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm Insertion Loss Isolation Return Loss Return Loss RF1, RF2 Input Power for 1 dB Compression “Off State” Input Third Order Intercept (Two-Tone Input Power= +7 dBm Each Tone, 1 MHz Tone Separation) Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 11 - 54 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC232LP4 / 232LP4E v04.0110 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Insertion Loss 0 -1 Isolation -10 -20 -30 -40 -50 -60 -70 -80 RF1 RF2 INSERTION LOSS (dB) -2 -3 +25 C +85 C -40 C -4 -5 -6 0 1 2 3 4 5 6 7 8 9 10 11 12 13 ISOLATION (dB) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 FREQUENCY (GH ) Q C (G ) Return Loss 0 RFC RF1, RF2 ON RF1, RF2 OFF 0.1 and 1 dB Input Compression Point 30 11 SWITCHES - SPDT - SMT 11 - 55 -5 RETURN LOSS (dB) 25 -10 P1dB (dBm) 20 -15 15 0.1 dB Compression Point 1 dB Compression Point -20 10 -25 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13 FREQUENCY (GHz) FREQUENCY (GH ) Input Third Order Intercept Point 60 55 50 IP3 (dBm) 45 +25 C +85 C -40 C 40 35 30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 FREQUENCY (GH ) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC232LP4 / 232LP4E v04.0110 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Absolute Maximum Ratings RF Input Power (Vctl = -5V) (0.5 - 12 GHz) RF1, RF2 Termination Control Voltage Range (A & B) Channel Temperature Thermal Resistance (RTH) (junction to lead) Storage Temperature Operating Temperature ESD Sensitivity (HBM) +30 dBm (@ +50 °C) +23.5 dBm +1V to -7.5V 150 °C 94 °C/W Control Voltages State Low High Bias Condition 0 to -0.2V @ 10 uA Max. -5V @ 10 uA Typ. to -7V @ 45 uA Typ. (0.5 Vdc) Truth Table Control Input Signal Path State B Low High RFC to RF1 ON OFF RFC to RF2 OFF ON A High Low -65 to +150 °C -40 to +85 °C Class 1A Caution: Do not “Hot Switch” power levels greater than +27 dBm (Vctl = 0/-5 Vdc). ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 11 SWITCHES - SPDT - SMT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC232LP4 HMC232LP4E Package Body Material Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H232 XXXX H232 XXXX RoHS-compliant Low Stress Injection Molded Plastic [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 11 - 56 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC232LP4 / 232LP4E v04.0110 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Suggested Driver Circuit 11 Pin Number 1, 2, 6, 7, 11, 12, 13, 14, 17, 18, 19, 20, 24 3, 5, 8, 10, 21, 23 Function N/C Description The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Package bottom must also be connected to PCB RF ground. This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. Interface Schematic GND 4, 9, 22 RFC, RF1, RF2 15 B See truth table and control voltage table. 16 A See truth table and control voltage table. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 - 57 SWITCHES - SPDT - SMT Pin Descriptions HMC232LP4 / 232LP4E v04.0110 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Evaluation PCB 11 SWITCHES - SPDT - SMT List of Materials for Evaluation PCB 107723 [1] Item J1 - J3 J4 - J6 C1, C2 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 pF Capacitor, 0603 Pkg. HMC232LP4 / HMC232LP4E SPDT Switch 107602 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. 11 - 58 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC232LP4 / 232LP4E v04.0110 GaAs MMIC SPDT NON-REFLECTIVE SWITCH, DC - 12 GHz Notes: 11 SWITCHES - SPDT - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 - 59