HMC251MS8_01

v01.0801 HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Features Divide-By-Two Low Phase Noise: -130 dBc/Hz @ 10KHz Single Positive Bias Voltage: +5.0V @ 27 mA Miniature Small Outline Pakcage: MSOP8 Typical Applications The HMC251MS8 is ideal for: • Wireless Local Loop 10 FREQ. DIVIDERS & DETECTORS - SMT • UNII & HiperLAN • ISM • VSAT Functional Diagram General Description The HMC251MS8 is a low noise divide-by-2 GaAs MMIC prescaler in an 8 lead surface mount MSOP plastic package. This device operates from 3.0 to 6.5 GHz (input frequency) with a single +5.0 V DC supply while drawing only 27 mA of current. The low residual phase noise of this prescaler helps the user maintain good system noise performance. Electrical Specifications, TA = +25° C, Vdd = +5.0V, 50 Ohm System Parameter Input Frequency Range Output Frequency Range Operating Input Power Range Fin = 3.0 - 4.0 GHz Fin = 4.0 - 5.0 GHz Fin = 5.0 - 6.0 GHz Fin = 6.0 - 6.5 GHz Fin = 3.0 - 4.0 GHz Fin = 4.0 - 5.0 GHz Fin = 5.0 - 6.0 GHz Fin = 6.0 - 6.5 GHz Fin = 5.0 - 6.0 GHz Offset from carrier = 10KHz Vdd = -5.0 Vdc 6 -2 -8 -3 -12 -14 -16 -17 -8.0 -7.7 -8.2 -8.5 -130 27 33 Condition Min Typical 3.0 - 6.5 1.5 - 3.25 10 10 10 7 -3 -3 -3 -3 Max Units GHz GHz dBm dBm dBm dBm dBm dBm dBm dBm dBc/Hz mA Output Power for Minimum Input Power Level (Note 1) Single-Side-Band Phase Noise Supply Current (Idd) Note 1. Output Power Measured at half the Input Frequency. 10 - 2 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com v01.0801 HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Output Power vs. Frequency @ Minimum Input Power Level 0 -2 Minimum Input Power vs. Input Frequency 20 MINIMUM INPUT POWER (dBm) OUTPUT POWER (dBm) 10 Guaranteed Operating Window -4 -6 -8 -10 -12 +85 C -40 C +25 C 0 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 3 -10 -40 C -20 +25 C +85 C -14 3 3.5 4 4.5 5 5.5 6 6.5 INPUT FREQUENCY (GHz) -30 3 3.5 4 4.5 5 5.5 6 6.5 INPUT FREQUENCY (GHz) Output Power for Input Power= +10 dBm* 0 -2 Single-Side-Band Phase Noise vs. Offset from Carrier, fin= 5 to 6 GHz -80 -90 -100 -110 -120 OUTPUT POWER (dBm) -4 -6 -8 -130 -10 -12 -14 3 3.5 4 4.5 5 5.5 6 6.5 INPUT FREQUENCY (GHz) -140 -150 -160 10 1 10 2 10 3 10 4 10 5 10 6 OFFSET FROM CARRIER (Hz) *Note: Output Power Measured @ fin/2 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com v01.0801 HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Output Power vs. Output Power vs. GaAs Input Frequency= 5.2 GHz PUMPED MIXER 17 - 5.8 GHz Input Power, MMIC SUB-HARMONICALLY Input Power, Input Frequency=25 GHz 0 -2 Output Power @ 2.6 GHz 0 -2 Output Power @ 2.9 GHz OUTPUT POWER (dBm) -6 -8 -10 -12 -14 -16 -18 -20 -10 -5 0 5 Feedthru Signal @ 5.2 GHz OUTPUT POWER (dBm) 10 FREQ. DIVIDERS & DETECTORS - SMT -4 -4 -6 -8 -10 -12 -14 -16 -18 Feedthru Signal @ 5.8 GHz 10 15 20 -20 -10 -5 0 5 10 15 20 INPUT POWER (dBm) INPUT POWER (dBm) RF IN S-Parameters * j1 RF OUT S-Parameters * j1 j0.5 3.0 GHz j2 j0.5 j2 3.25 GHz j0.2 j5 j0.2 j5 6.5 GHz 1.5 GHz 0 0.2 0.5 1 2 5 0 0.2 0.5 1 2 5 -j0.2 -j5 -j0.2 -j5 -j0.5 -j2 -j0.5 -j2 -j1 -j1 *S-Parameter Data is Available @ www.hittite.com For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 4 v01.0801 HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Absolute Maximum Ratings Vdd Maximum Input Power (Vdd = +5.0 Vdc) Storage Temperature Operating Temperature +8 Vdc 20 dBm -65 to +150 °C -40 to +85 °C 10 FREQ. DIVIDERS & DETECTORS - SMT NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 8. CLASSIFIED AS MOISTURE SENSITIVITY LEVEL (MSL) 1. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 5 v01.0801 HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Application Circuit 10 FREQ. DIVIDERS & DETECTORS - SMT Operating Notes: 1. With no input signal, or input signals below the minimum input power level, the prescaler will self-oscillate. 2. DC blocks on the RF ports are not required but are recommended if DC voltages exceeding 8 volts are present. 10 - 6 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com v01.0801 HMC251MS8 GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz Eval Board Layout (Top View) 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 7 List Of Materials Item J1, J2 J3, J4 C1, C2 U1 PCB* * Circuit Board Material: 4350 Description PC Mount SMA Connector DC Pin 330 pF capacitor, 0603 Pkg. HMC251MS8 Prescaler 102285 Eval Board The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at RF IN and RF OUT should have 50 ohm impedance and the package ground leads should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com