HMC305ALP4E

HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz Features 0.5 dB LsB steps to 15.5 dB CMos Compatible serial Data Interface sPI Compatible serial output ±0.3 dB typical Bit error 24 Lead 4x4mm QFn Package: 16mm² Included in the HMC-DK004 Designer’s Kit 8 AttenuAtors - DIGItAL - sMt Typical Applications the HMC305ALP4(e) is ideal for: • Cellular/3G Infrastructure • Fixed Wireless, WiMax & WiBro • test Instrumentation Functional Diagram General Description the HMC305ALP4(e) is a broadband 5-bit positive control GaAs IC digital attenuator with CMos compatible serial-to-parallel driver package in a leadless QFn 4x4 mm sMt package. Covering 0.7 to 3.8 GHz, the insertion loss is typically less than 1.5 to 2 dB. the attenuator bit values are 0.5 (LsB), 1, 2, 4, and 8 dB for a total attenuation of 15.5 dB. Attenuation accuracy is excellent at ±0.25 dB typical with an IIP3 of up to +52 dBm. Five bit serial control words are used to select each attenuation state. A single Vcc bias of +3V to +5V applied through an external 5 kohm resistor is required. Electrical Specifications, TA = +25° C, Vcc = +3V to +5V Parameter Frequency 0.7 - 1.4 GHz 1.4 - 2.3 GHz 2.3 - 2.7 GHz 2.7 - 3.8 GHz 0.7 - 3.8 GHz 0.7 - 1.4 GHz 1.4 - 2.3 GHz 2.3 - 2.7 GHz 2.7 - 3.8 GHz 0.7 - 0.9 GHz 0.9 - 2.2 GHz 2.2 - 3.8 GHz Vcc = 5V Vcc = 3V Vcc = 5V Vcc = 3V 0.7 - 3.8 GHz 0.7 - 3.8 GHz Min. typical 1.2 1.5 1.8 2.0 15.5 17 18 19 15 ± (0.5 +5% of Atten. setting) Max ± (0.3 +4% of Atten. setting) Max ± (0.5 +5% of Atten. setting) Max 25 23 52 48 750 830 Max. 1.5 2.0 2.3 2.5 units dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm dBm dBm ns ns Insertion Loss Attenuation range return Loss (rF1 & rF2, All Atten. states) Attenuation Accuracy: (referenced to Insertion Loss) All Attenuation states Input Power for 0.1 dB Compression Input third order Intercept Point (two-tone Input Power = 0 dBm each tone) switching Characteristics trIse, tFALL (10/90% rF) ton, toFF (Latch enable to 10/90% rF) 0.7 - 3.8 GHz 8-1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz Insertion Loss 0 -0.5 INSERTION LOSS (dB) RETURN LOSS (dB) -1 -1.5 -2 -2.5 -3 -3.5 -4 0.5 +25C +85C -40C Return Loss RF1, RF2 (Only Major States are Shown) 0 -5 -10 0.5 dB -15 -20 -25 1 dB 4 dB 1.5 2 2.5 3 3.5 4 -30 0.5 2 dB 8 dB I.L. 15.5 dB 8 AttenuAtors - DIGItAL - sMt 8-2 1 1.5 2 2.5 3 3.5 4 1 FREQUENCY (GHz) FREQUENCY (GHz) Normalized Attenuation (Only Major States are Shown) 0 NORMALIZED ATTENUATION (dB) -2 -4 Bit Error vs. Attenuation State 1 0.75 BIT ERROR (dB) 0.5 0.25 0 3.5 GHz 1.9 GHz 0.9 GHz -6 -8 -10 -12 -14 -16 0.5 -0.25 -0.5 2.4 GHz 0 2 4 6 8 10 12 14 16 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) ATTENUATION STATE (dB) Bit Error vs. Frequency (Only Major States are Shown) 3 Relative Phase vs. Frequency (Only Major States are Shown) 60 40 20 0 -20 -40 0.5, 1, 2, 4, 8 dB 15.5 dB BIT ERROR (dB) 2 8 dB 1 15.5 dB 0 0.5, 1, 2, 4 dB -1 0.5 RELATIVE PHASE (deg.) 4 -60 1 1.5 2 2.5 3 3.5 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) FREQUENCY (GHz) Note: All Data Typical Over Voltage (+3V to +5V) & Temperature (-40°C to +85°C). F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz 8 AttenuAtors - DIGItAL - sMt Worst Case Step Error Between Successive Attenuation States 1.2 0.8 STEP ERROR (dB) 0.4 0 -0.4 -0.8 -1.2 0.5 Digital Control Voltages state Low High Vcc = +5V 0 to 1.3V 3.5 to 5V Vcc = +3V 0 to 0.7V 2.3 to 3V Serial Input Truth Table Latch enable X X 1 1.5 2 2.5 3 3.5 4 shift Clock X á X reset L H H Function shift register cleared shift register clocked Contents of shift register transferred to Digital Attenuator á FREQUENCY (GHz) Timing Parameter serial Input setup time Hold time from serial Input to shift Clock setup time from shift Clock to Latch enable Propagation delay, Latch enable to C0.5 through C8 setup time from reset to shift Clock Clock Frequency (1/tclk) symbol Vcc = +5V Min. ts th 20 0 Max. Vcc = +3V Min. 100 5 Max. ns ns units Truth Table serial Control Input C 0.5 High Low High tlsup 40 100 ns High High High tpd 30 70 ns Low C1 High High Low High High High Low C2 High High High Low High High Low C4 High High High High Low High Low C8 High High High High High Low Low Attenuation setting rF1 - rF2 reference I.L. 0.5 dB 1 dB 2 dB 4 dB 8 dB 15.5 dB Max. Atten. fclk 20 - 30 50 - 10 ns MHz Any combination of the above states will provide an attenuation approximately equal to the sum of the bits selected. Timing Diagram 8-3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz Logic / Functional Diagram 8 AttenuAtors - DIGItAL - sMt Programming Example to Select 0.5 dB Attenuation State F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-4 HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz 8 AttenuAtors - DIGItAL - sMt Pin Descriptions Pin number 1, 3, 4, 6, 10, 12, 13, 15, 16, 18 Function n/C Description these pins are not connected internally. However, all data shown herein was measured with these pins connected to rF/DC Ground. this pin is DC coupled and matched to 50 ohms Blocking capacitors are required. select value based on lowest frequency of operation. Interface schematic 2, 17 rF1, rF2 5 serial output serial data output. serial input data delayed by 8 clock cycles 7 reset see truth table, control voltage table and timing diagram. 8 shift Clock 9 Latch enable 11 serial Input 14 19 - 24 Vcc GnD supply Voltage. Package bottom has an exposed metal paddle that must also be connected to rF/DC Ground. 8-5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz Application Circuit 8 AttenuAtors - DIGItAL - sMt DC blocking capacitors C1 & C2 are required on rF1 & rF2. Choose C1 = C2 = 100 ~ 300 pF to allow lowest customer specific frequency to pass with minimal loss. r1 = 5 kohm is required to supply voltage to the circuit through either PIn 2 or PIn 17. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-6 HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz 8 AttenuAtors - DIGItAL - sMt Absolute Maximum Ratings Digital Inputs (reset, shift Clock, Latch enable & serial Input) Digital outputs (serial output) DC Current on serial output Bias Voltage (Vcc) storage temperature operating temperature rF Input Power (0.7 - 3.8 GHz) esD sensitivity (HBM) -0.5 to (Vcc + 0.5) V -0.5 to (Vcc + 0.5) V ±35 mA +5.6 V -65 to +150 °C -40 to +85 °C +26 dBm Class 1A eLeCtrostAtIC sensItIVe DeVICe oBserVe HAnDLInG PreCAutIons Outline Drawing notes: 1. LeADFrAMe MAterIAL: CoPPer ALLoY 2. DIMensIons Are In InCHes [MILLIMeters] 3. LeAD sPACInG toLerAnCe Is non-CuMuLAtIVe 4. PAD Burr LenGtH sHALL Be 0.15mm MAXIMuM. PAD Burr HeIGHt sHALL Be 0.05mm MAXIMuM. 5. PACKAGe WArP sHALL not eXCeeD 0.05mm. 6. ALL GrounD LeADs AnD GrounD PADDLe Must Be soLDereD to PCB rF GrounD. 7. reFer to HIttIte APPLICAtIon note For suGGesteD LAnD PAttern. Package Information Part number HMC305ALP4 HMC305ALP4e Package Body Material Low stress Injection Molded Plastic roHs-compliant Low stress Injection Molded Plastic Lead Finish sn/Pb solder 100% matte sn MsL rating MsL1 MsL1 [1] Package Marking [3] H305A XXXX H305A XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 8-7 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC305ALP4 / 305ALP4E v02.0311 0.5 dB LSB GaAs MMIC 5-BIT SERIAL CONTROL DIGITAL ATTENUATOR, 0.7 - 3.8 GHz Evaluation Circuit Board 8 AttenuAtors - DIGItAL - sMt List of Materials for Evaluation PCB 108782 [1] Item J1 - J2 J3 J6, J7 C1, C2 C3 r1 u1 PCB [2] Description PCB Mount sMA Connector 18 Pin DC Connector DC Pin 100 pF Capacitor, 0402 Pkg. 0.01 µF Capacitor, 0402 Pkg. 5 kohm resistor, 0402 Pkg. HMC305ALP4(e) Digital Attenuator 108780 evaluation PCB [1] reference this number when ordering complete evaluation PCB [2] Circuit Board Material: rogers 4350 the circuit board used in the application should use rF circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed ground paddle should be connected directly to the ground plane similar to that shown below. A sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board as shown is available from Hittite Microwave Corporation upon request. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8-8