HMC316MS8_06

HMC316MS8 / 316MS8E v02.0505 GaAs MMIC HIGH IP3 DOUBLEBALANCED MIXER, 1.5 - 3.8 GHz Designer’s Kit Available Typical Applications The HMC316MS8 / HMC316MS8E is ideal for: • Cellular Basestations Features Conversion Loss: 8 dB LO/RF Isolation: >35 dB Input IP3: +25 dBm Ultra Small Package: 110 >110 1 -8 0 72 >110 >110 2 3.6 22 77 >110 >110 3 1.1 44 60 91 >110 4 29 48 85 91 >110 RF = 2.08 GHz @ -10 dBm LO = 1.9 GHz @ +17 dBm All values in dBc relative to the IF output power. * Two-tone input power = 0 dBm each tone, 1 MHz spacing. 7 - 178 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC316MS8 / 316MS8E v02.0505 GaAs MMIC HIGH IP3 DOUBLEBALANCED MIXER, 1.5 - 3.8 GHz Absolute Maximum Ratings RF / IF Input LO Drive Storage Temperature Operating Temperature IF DC Current ESD Sensitivity (HBM) +22 dBm +27 dBm -65 to +150 °C -40 to +85 °C ±18 mA Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 7 MIXERS - SMT NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Outline Drawing Package Information Part Number HMC316MS8 HMC316MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H316 XXXX H316 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 179 HMC316MS8 / 316MS8E v02.0505 GaAs MMIC HIGH IP3 DOUBLEBALANCED MIXER, 1.5 - 3.8 GHz Evaluation PCB 7 MIXERS - SMT List of Materials for Evaluation PCB 101830 [1] Item J1 - J3 U1 PCB [2] Description PCB Mount SMA RF Connector HMC316MS8 / HMC316MS8E Mixer 101828 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown below. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board as shown is available from Hittite upon request. 7 - 180 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC316MS8 / 316MS8E v02.0505 GaAs MMIC HIGH IP3 DOUBLEBALANCED MIXER, 1.5 - 3.8 GHz Notes: 7 MIXERS - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 181