HMC322LP4_08

HMC322LP4 / 322LP4E v05.1205 GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 8 GHz Typical Applications This switch is suitable for usage in DC - 8.0 GHz 50Ohm or 75-Ohm systems: • Broadband • Fiber Optics • Switched Filter Banks • Wireless below 8 GHz Features Broadband Performance: DC - 8.0 GHz High Isolation: >30 dB@ 6 GHz Low Insertion Loss: 2.4 dB@ 6 GHz Integrated 3:8 TTL Decoder 4x4 mm SMT Package Functional Diagram General Description The HMC322LP4 & HMC322LP4E are broadband non-reflective GaAs MESFET SP8T switches in low cost leadless surface mount packages. Covering DC to 8 GHz, this switch offers high isolation and low insertion loss. This switch also includes an on board binary decoder circuit which reduces the required logic control lines to three. The switch operates using a negative control voltage of 0/-5 volts, and requires a fixed bias of -5V. This switch is suitable for usage in 50-Ohm or 75-Ohm systems. 10 SWITCHES - SMT Electrical Specifi cations, TA = +25° C, With 0/-5V Control, 50 Ohm System Parameter Insertion Loss Frequency DC - 2.0 GHz DC - 4.0 GHz DC - 8.0 GHz DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz DC - 8.0 GHz “On State” “Off State” DC - 2.0 GHz DC - 8.0 GHz DC - 8.0 GHz 0.5 - 8.0 GHz 0.5 - 8.0 GHz 35 30 25 20 9 6 7 19 36 Min. Typ. 2.1 2.3 2.5 40 35 30 25 12 10 10 23 40 50 150 Max. 2.5 2.7 2.9 Units dB dB dB dB dB dB dB dB dB dB dBm dBm ns ns Isolation Return Loss Return Loss Input Power for 1 dB Compression Input Third Order Intercept (Two-Tone Input Power = +7 dBm Each Tone) Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) DC - 8.0 GHz 10 - 178 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC322LP4 / 322LP4E v05.1205 GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 8 GHz Insertion Loss vs. Temperature 0 Isolation 0 -10 RF1 RF2 RF3 RF4 RF5 RF6 RF7 RF8 -1 INSERTION LOSS (dB) ISOLATION (dB) +25 C -40 C +85 C -20 -30 -40 -50 -60 -70 -2 -3 -4 -5 0 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) 0 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) 10 SWITCHES - SMT 10 - 179 Return Loss 0 0.1 and 1 dB Input Compression Point 30 INPUT COMPRESSION POINT (dBm) -5 RETURN LOSS (dB) 25 -10 20 -15 RFC RF1-8 ON RF1-8 OFF 15 -20 0.1dB Compression Point 1dB Compression Point -25 0 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) 10 0 1 2 3 4 5 6 7 8 FREQUENCY (GHz) Input Third Order Intercept Point INPUT THIRD ORDER INTERCEPT (dBm) 50 45 40 35 30 1 2 3 4 5 6 7 8 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC322LP4 / 322LP4E v05.1205 GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 8 GHz Bias Voltage & Current Vee Range = -5.0 Vdc ± 10% Vee (Vdc) -5.0 Iee (Typ.) (mA) 5.0 Iee (Max.) (mA) 9.0 Truth Table Control Input A High Low High B High High Low Low High High Low Low C High High High High Low Low Low Low Signal Path State RFCOM to: RF1 RF2 RF3 RF4 RF5 RF6 RF7 RF8 Control Voltages State Low High Bias Condition -3V to 0 Vdc @ 25 uA Typical -5 to -4.2 Vdc @ 5 uA Typical Low High Low High Low 10 SWITCHES - SMT TTL Interface Circuit Note: Control inputs A, B, and C can be driven directly with TTL logic with -5 Volts applied to the HCT logic gates Vee pin and to Vee (pin 8) of the RF Switch. 10 - 180 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC322LP4 / 322LP4E v05.1205 GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 8 GHz Absolute Maximum Ratings Bias Voltage Range (Vee) Control Voltage Range (A, B, & C) Storage Temperature Operating Temperature Maximum Input Power ESD Sensitivity (HBM) -7.0 Vdc Vee -0.5V to +1.0 Vdc -65 to +150 °C -40 to +85 °C 26 dBm Class 1B ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing 10 SWITCHES - SMT NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC322LP4 HMC322LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H322 XXXX H322 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 181 HMC322LP4 / 322LP4E v05.1205 GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 8 GHz Pin Descriptions Pin Number 1, 3, 5, 7, 12, 14, 16, 18, 21, 23 2, 4, 6, 13, 15, 17, 19, 22, 24 Function Description Package bottom has exposed metal paddle that must also be connected to PCB RF ground. Interface Schematic GND RF1 - RF8 & RFC This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. 8 VEE Supply Voltage = -5V ± 10% 10 SWITCHES - SMT 9 CTLC See truth table and control voltage table. 10 CTLB See truth table and control voltage table. 11 CTLA See truth table and control voltage table. 20 N/C This pin should be connected to PCB RF ground to maximize isolation. 10 - 182 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC322LP4 / 322LP4E v05.1205 GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 8 GHz Evaluation PCB 10 SWITCHES - SMT List of Materials for Evaluation PCB 107780 [1] Item J1 - J9 J10 - J14 C1 - C9 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 pF Capacitor, 0402 Pkg. HMC322LP4 / HMC322LP4E SP8T Switch 104687 Evaluation PCB 1.73”x1.46” [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 183