HMC345LP3E

HMC345LP3 / 345LP3E v04.0805 GaAs MMIC SP4T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8 GHz Typical Applications This switch is suitable for usage in DC - 8.0 GHz 50Ohm or 75-Ohm systems: • Broadband • Fiber Optics • Switched Filter Banks • Wireless below 8 GHz Features Broadband Performance: DC - 8 GHz High Isolation: 35 dB@ 6 GHz Low Insertion Loss: 2.2 dB@ 6 GHz Integrated Positive Supply 2:4 TTL Decoder 3 x 3 mm SMT Package Functional Diagram General Description The HMC345LP3 & HMC345LP3E are broadband non-reflective GaAs MESFET SP4T switches in low cost leadless surface mount packages. Covering DC to 8 GHz, this switch offers high isolation and low insertion loss. This switch also includes an on board binary decoder circuit which reduces the required logic control lines to two. The switch operates using a positive control voltage of 0/+5V, and requires a fixed bias of +5V. 10 SWITCHES - SMT * Blocking capacitors are required at ports RFC and RF1, 2, 3, & 4. Their value will determine the lowest transmission frequency. Electrical Specifi cations, TA = +25° C, With 0/+5V Control, 50 Ohm System Parameter Insertion Loss Frequency DC - 2.0 GHz DC - 6.0 GHz DC - 8.0 GHz DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz DC - 8.0 GHz DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz DC - 8.0 GHz 2.0 - 8.0 GHz 2.0 - 8.0 GHz 2.0 - 8.0 GHz 37 32 31 27 10 8 7 6 6 17 37 Min. Typ. 2.0 2.2 2.4 42 37 35 32 13 11 10 9 10 21 45 50 120 Max. 2.4 2.6 2.9 Units dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm ns ns Isolation Return Loss “On State” Return Loss (RF1 - RF4) Input Power for 1 dB Compression “Off State” Input Third Order Intercept (Two-Tone Input Power = +7 dBm Each Tone, 1MHz Tone Separation) Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) DC - 8.0 GHz 10 - 208 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC345LP3 / 345LP3E v04.0805 GaAs MMIC SP4T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8 GHz Insertion Loss vs. Temperature 0 Isolation 0 -10 RF1 RF2 RF3 RF4 -1 INSERTION LOSS (dB) ISOLATION (dB) +25 C -40 C +85 C -20 -30 -40 -50 -60 -70 -2 -3 -4 -5 0 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) 0 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) 10 SWITCHES - SMT 10 - 209 Return Loss 0 RFC RF1-RF4 ON RF1-RF4 OFF 0.1 and 1 dB Input Compression Point 25 INPUT COMPRESSION POINT (dBm) -5 RETURN LOSS (dB) 22 -10 19 -15 16 -20 13 0.1dB Compression Point 1.0dB Compression Point -25 0 1 2 3 4 5 6 7 8 9 FREQUENCY (GHz) 10 1 2 3 4 5 6 7 8 FREQUENCY (GHz) Input Third Order Intercept Point INPUT THIRD ORDER INTERCEPT (dBm) 60 55 50 45 40 35 30 1 2 3 4 5 6 7 8 FREQUENCY (GHz) RF1 RF2 RF3 RF4 * Isolation is recorded above insertion loss & measured at output of switch. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC345LP3 / 345LP3E v04.0805 GaAs MMIC SP4T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8 GHz Absolute Maximum Ratings Bias Voltage Range (Vdd) Control Voltage Range (A & B) Channel Temperature Thermal Resistance (Insertion Loss Path) Thermal Resistance (Terminated Path) Storage Temperature Operating Temperature Maximum Input Power ESD Sensitivity (HBM) +7.0 Vdc -0.5V to Vdd +1.0 Vdc 150 °C 143 °C/W Bias Voltage & Current Vdd Range = +5.0 Vdc ± 10% Vdd (Vdc) +5.0 Idd (Typ.) (mA) 3.0 Idd (Max.) (mA) 6.0 Control Voltages 1030 °C/W State -65 to +150 °C -40 to +85 °C +24 dBm Class 1A Low High Bias Condition 0 to +0.8 Vdc @ 5 uA Typical +2.0 to +5.0 Vdc @ 60 uA Typical 10 SWITCHES - SMT ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Truth Table Control Input A Low High Low High B Low Low High High Signal Path State RFCOM to: RF1 RF2 RF3 RF4 Note: DC blocking capacitors are required at ports RFC and RF1, 2, 3, & 4. Their value will determine the lowest transmission frequency. 10 - 210 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC345LP3 / 345LP3E v04.0805 GaAs MMIC SP4T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8 GHz Outline Drawing 10 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC345LP3 HMC345LP3E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] 345 XXXX 345 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 211 SWITCHES - SMT HMC345LP3 / 345LP3E v04.0805 GaAs MMIC SP4T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8 GHz Pin Descriptions Pin Number 1, 4, 9, 12, 15 2, 3, 10, 11, 13 Function RF4, RF3, RF2, RF1, RFC Description This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required. This pin should be connected to PCB RF ground to maximize isolation. Package bottom has exposed metal paddle that must also be connected to PCB RF ground. Interface Schematic N/C 5, 14, 16 GND 6 VDD Supply Voltage +5V ± 10% 10 SWITCHES - SMT 7 CTLB See truth table and control voltage table. 8 CTLA See truth table and control voltage table. 10 - 212 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC345LP3 / 345LP3E v04.0805 GaAs MMIC SP4T NON-REFLECTIVE POSITIVE CONTROL SWITCH, DC* - 8 GHz Evaluation PCB 10 SWITCHES - SMT List of Materials for Evaluation PCB 108333 [1] Item J1 - J7 J8 - J11 C1 - C7 C8 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 pF Capacitor, 0402 Pkg. 10k pF Capacitor, 0603 Pkg. HMC345LP3 / HMC345LP3E SP4T Switch 104708 Evaluation PCB 1.29”x1.55” [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 213